@dc42 @dc42
Thanks.
Well the SD card speed may not be helping

24/10/2021, 19:42:10	SD read speed for 10.0Mbyte file was 0.62Mbytes/sec
24/10/2021, 19:41:53	SD write speed for 10.0Mbyte file was 0.45Mbytes/sec

This is with the supplied card. I'll replace it with another. I've just read the specs and I can't use one > 32gb so I'll have to order one as all mine are 64.

Uploading a .dummy file I'm getting 180 KiB/sec.

I have wifi debug on I'll leave it for a while see if anything gets logged - will it just log to console?

@mart1ns

@zapta
Actually it's far far worse than I initially thought as I'd only done small models for printer calibration.

I've Just performed a test.

5 uploads of the same sliced gcode in Superslicer. laptop connected via ethernet to router to eliminate laptop -> router wifi.

I've located the Octoprint pi on the frame of the V-Core 3 right next to the duet wifi antenna.

gcode size 30.1mb

Average upload time.
-> Octoprint on pi : 2.1 seconds
-> duet : 1min 11 seconds.

Model failed to transer to duet twice during the test.

Surely there must be an issue with the board. The Pi isn't noted for having the best wifi, but this duet is incredibly unstable.

I've also noticed that as I've been editing config,g setting the new printer up I'm doing a lot of software resets from the Web control. At least 50% of the time the DWC fails to reconnect to the board following a reset. I have to power cycle the printer to regain connection, often it will then drop out again and reconnect immediately.

In addition to that often when I'm editing the config connection will be lost, meaning that the editor closes and all changes are lost. I've also experience loss of connection from DWC during a save of the config. This results in the config file being deleted from the SD and I've had to recreate it using the backup.

The duet3 mini5 wifi experience has been infuriating to say the least.

I'm having an issue with the stability of the wifi.

My home wifi coverge is good. I have a Synology RT2600ac main router and 2 synology MR2200ac mesh repeaters. The house is a 3 floor house. Router on floor 1 directly under the Duet3 mini5 wifi. One mesh point is in the room next to the Duet, the other mesh point on the floor above.

I have other kit in the same room as the duet which has no connectivity issues. There are 2 other printers next to the duet running Octoprint on pi's and they stay connected no problem.

Uploading gcode to the duet is 5 times slower than sending the same models from the slicer to the pi's
console.txt

WiFi signal strength -46dBm

; ~PanelDue
M575 P1 S1 B57600

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"V-Core 3"                        ; set printer name
M669 K1                                 ; CoreXY
G29 S1                                  ; Set Units to Millimeters

; Network
M552 S1                        ; enable network and acquire dynamic address via DHCP
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Drives
M569 P0.0 S0 D3                         ; physical drive 0.0 goes backwards
M569 P0.1 S0 D3                         ; physical drive 0.1 goes backwards
M569 P0.2 S0 D3                         ; physical drive 0.2 goes backwards
M569 P0.3 S1 D3                         ; physical drive 0.3 goes forwards
M569 P0.4 S1 D3                         ; physical drive 0.4 goes forwards
M569 P0.5 S1 D3                         ; physical drive 0.5 goes forwards
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5        ; set drive mapping
M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation

M92 X80.00 Y80.00 Z800.00             ; set steps per mm
M906 X1000 Y1000 Z800 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

M566 X400.00 Y400.00 Z6.00 E120.00 P1          ; set maximum instantaneous speed changes (mm/min)
M203 X10800.00 Y10800.00 Z1000.00 E3600.00     ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E3600.00        ; set accelerations (mm/s^2)

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X310 Y300 Z300 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"io1.in"                           ; configure active high endstops
M574 Y2 S1 P"io0.in"                           ; configure active high endstops
M574 Z1 S2

M671 X-4.5:150:304.5 Y-4.52:305:-4.52 S5       ; define positions of Z leadscrews or bed levelling screws
M557 X20:280 Y20:280 P5                        ; define 5x5 mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed"    ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                     ; create bed heater output on out5 and map it to sensor 0
M307 H0 B0 S1.00                                       ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                ; map heated bed to heater 0
M143 H0 S110                                           ; set temperature limit for heater 0 to 110C

; Bed PID Tune
 M307 H0 B0 R0.634 C663.6 D8.17 S1.00 V24.0

; Fans
M950 F0 C"out3" Q500                   ; create fan 0 on pin out3 and set its frequency
M106 P0 C"Hotend Fan" S0 H1 T30 L255   ; set fan 0 name and value. Thermostatic control turned on for Hotend
M950 F1 C"out4" Q500                   ; create fan 1 on pin out4 and set its frequency
M106 P1 C"Layer Fan" S0 H-1 L255       ; set fan 1 name and value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F1           ; define tool 0
G10 P0 X0 Y0 Z0            ; set tool 0 axis offsets
G10 P0 R0 S0               ; set initial tool 0 active and standby temperatures to 0C

M950 H1 C"out1" T1         ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00           ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280               ; set the maximum temperature in C for heater

; EVA 2 / BMG / E3D V6

M92 E411.06          ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800         ; set extruder motor current (mA) and idle factor in per cent

;M308 S1 P"temp1" Y"pt1000" B4092 A"hotend" ; T100000 B4725 C7.06e-8
M308 S1 P"temp1" Y"pt1000" T100000 B4725 C7.06e-8  ; from config tool - Semitec 104-GT2
M307 H1 B0 R2.452 C223.2 D6.52 S1.00 V23.9

; Z-Probe
; Inductive Probe
M558 P5 C"!io3.in" H5 F400 T5000       ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-30 Y-15 Z0.20               ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
; BLTouch
;M950 S0 C"io2.out"                     ; Create a servo pin on io2
;M558 P5 C"io2.in" H5 F240 T10800 A1    ; set Z probe type to unmodulated and the dive height + speeds
G31 P25 X-23.00 Y-13.00 Z0.859          ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed

M404 N1.75 D0.4                                 ; Filament width and nozzle diameter
T0

; Pressure Advance
; M572 D0 S0.10
M501

@mart1ns
I suspected the extension cabling, so plugged the BLTouch directly into the board using the attached short leads. Same problem

I tried a PINDA from my Mk3s. Wired into IO_3 and it worked fine. Z triggered as expected.

Ratrig coreXY VCore3. New build

BLTouch does self check a startup
Deploys and retracts correctly with M280 P0 Sx
Deploys correctly when Z homing

Triggering probe doesn't stop the bed

Connected to IO_2, just using a temp extension for now until working and I'll crimp a 5pin connector on. Wiring looks right to me (White/Brown/Black/Yellow/Red - top to bottom)

config,g

; Endstops
M574 X1 S1 P"io1.in"
M574 Y2 S1 P"io0.in"
M574 Z1 S2

; BLTouch
M950 S0 C"io2.out"
M558 P9 C"io2.in" H5 F240 T10800 A1
G31 P25 X-28.00 Y-13.00 Z0.90

homez

; BLTouch
M280 P0 S160
M280 P0 S90

G91
G1 H2 Z5 F6000
G90
G1 X150 Y150 F10000
G30

; Uncomment the following lines to lift Z after probing
G91
G1 Z5 F100
G90