Posts made by mpsanders

@Phaedrux said in Duet 2 wifi + FLSUN Q5 problems with probe:

: M558 P8 C"!e0_stop"

M558 P8 C"!e0_stop" did the trick. The probe isn't giving an already triggered error anymore, however, it did expose a mechanical issue I'm having where it probes the first two points, but then when going to probe the third point, it jerks and pulls the effector up and stops triggering the probe. I am fairly sure this is some issue with one of the axis' arms but it looks like once I get that solved, it'll work fine. I really appreciate the assistance! You are awesome!

@Phaedrux It's currently wired to e0_stop. It's a 3 pin connector like a normal endstop so it won't go into zprobein and there is a separate endstop plugged into zstop. I don't remember setting it up the first time but my guess is that this is the issue - when I generated the rrf 3.0 config, I used my old config.json because I couldn't remember all the things I had to change initially. The probe came up as 'null' so I tried to fix it using generic google search which is where the incorrect type line came from. I am sorry that I can't remember how I initially got it working with it plugged into e0_stop - it's just been a while. Is there a way to get it working with the current config or do I need to make physical changes?

@Phaedrux Howdy, thank you for the reply.
It's a switch-type probe but it's weird because it's not always on the effector - you attach it just for probing and then remove it when you're done.

4/8/2024, 3:50:23 PM	M98 P"config.g"
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is enabled on port 23
Error: Pin 'fan1' is not free
Error: Fan number 2 not found

Would the ! go in front of the zstop in the m574 line or in front of the zprobe.in+zprobe.mod part?

I'm not sure what's going on with the fans either - Everything was working in firmware version 2.0.5 but I left it sitting around for a couple of years and I didn't test it before updating the firmware the other day, so I'm not sure if the issues I'm having strictly come from the firmware change or if something happened while it was just sitting around. I'm guessing it's firmware but since I failed to test it before upgrading I can't say that for sure. Once again, thank you for the help, I really appreciate it!

Howdy,

I've had my FLSUN Q5 on a shelf since I moved and had kinda forgotten about it. Today I tried to get it running. It was running a really old version of firmware, 2.0.5. I upgraded from that to 3.0, then to 3.3, then to 3.4.6. I'm guessing something changed since then because I'm now having issues with my probe. It is saying that the probe is already triggered whenever I try to run a probe. I don't know enough to be able to determine what is causing this. Any assistance would be appreciated!

4/7/2024, 5:43:35 PM m115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.4.6 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2023-07-21 14:08:28

Here is my config.g file:

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.4.1 on Sun Apr 07 2024 16:47:41 GMT-0500 (Central Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Q5Delta"                                    ; set printer name
M665 R104.3 L215 B104 H220                         ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                      ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S1                                         ; enable FTP
M586 P2 S1                                         ; enable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.02 Y79.94 Z80.07 E392.00                   ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E6000.00           ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E6000.00        ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E2000.00           ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 Z0 S1                                         ; set minimum Z

; Endstops
M574 X2 S1 P"xstop"                                ; configure switch-type (e.g. microswitch) endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop"                                ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop"                                ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin null

; Z-Probe
M558 P5 C"zprobe.in+zprobe.mod" H5 I1 F600 T9000   ; set Z probe type to switch and the dive height + speeds
G31 P25 X-2 Y-2 Z20                                ; set Z probe trigger value, offset and trigger height
M557 R100 S40                                      ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H2 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H2 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T38                                  ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan1" Q500                               ; create fan 2 on pin fan1 and set its frequency
M106 P2 S1 H1:0 T38                                ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H2 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
; M591 D0 C3 P2 E6.0                               ;This is the command for filament monitoring using an optical on/off switch

M579 X1.012 Y0.9871

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

That got it going, thank you very much!

Howdy Phaedrux,

Thank you for the info! The printer is an FLSUN Q5 delta printer - I imagine that I will need to update it to rrf3 at some point, just got a bit overwhelmed reading all of the commands I'll need to change and whatnot - but I don't have any special attachment to version 2. If I can get it working for now that would be cool, but if it's necessary to update to rrf3 first I'll give that a go. Here is my current config.g:

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Fri Dec 04 2020 07:23:38 GMT-0600 (Central Standard Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Q5Delta"                                    ; set printer name
M665 R104.3 L215 B104 H220                         ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                      ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S1                                         ; enable FTP
M586 P2 S1                                         ; enable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.02 Y79.94 Z80.07 E392.00                   ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E6000.00           ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E6000.00        ; set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E2000.00           ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 Z0 S1                                         ; set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                                   ; set active high endstops

; Z-Probe
M558 P4 H5 F600 T9000 I1                           ; set Z probe type to switch and the dive height + speeds
G31 P25 X-2 Y-2 Z20                                ; set Z probe trigger value, offset and trigger height
M557 R100 S40                                      ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T38                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1:0 T38                        ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
; M591 D0 C3 P2 E6.0                               ;This is the command for filament monitoring using an optical on/off switch

M579 X1.012 Y0.9871

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Howdy Veti,

Thank you very much for the reply. I am on fw version 2.0.5, which is what the online configurator gave me as the latest available. The m950 command does not appear to be supported in this version. Is there an analogous command in 2.0.5? I looked at the process to upgrade to rrf3 and I think it's going to take me a while to figure out. Again, sorry for the noob questions - I will learn.

Howdy y'all,

I have an issue with H1 on my board - a piece of ferrule broke off inside and I can't get it out. Is there a way to configure the printer to use H2 instead of H1? This is my first Duet board so apologies if this is super easy.