Posts made by nicolo17

@phaedrux Today a tried to use another duet 2 wifi and now the printer works... I think the other board is broken... I'll try to use it with a duex so I can connect motors directly to it, I hope it will work. Thank you very much for your help!

@phaedrux

@nicolo17 I have ''Driver 4: over temperature warning, over temperature shutdown, phase A short to ground, phase B short to ground, standstill, SG min n/a'' because I removed this driver from the board because was burned during an old project

@hayseed_byte @Phaedrux Thank you! I tried to change speed and acceleration (now I put very low values) in config.g under "drivers" sectionandand I'm still getting the same error
This is my config.g section:
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E100.00 ; set steps per mm
M566 X100.00 Y100.00 Z5.00 E100.00 ; set maximum instantaneous speed changes (mm/min)
M203 X400.00 Y400.00 Z50.00 E400.00 ; set maximum speeds (mm/min)
M201 X900.00 Y900.00 Z70.00 E2500.00 ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30

I also share my M122 response, if it can help:
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.1 (2022-06-01 21:05:28) running on Duet WiFi 1.02 or later
Board ID: 08DGM-95BNL-MGPSN-6J9F6-3S46N-TJWMW
Used output buffers: 3 of 26 (26 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 75168 of which 12 recycled
Never used RAM 12968, free system stack 130 words
Tasks: NETWORK(ready,6.4%,219) HEAT(notifyWait,0.0%,329) Move(notifyWait,0.0%,312) MAIN(running,92.6%,440) IDLE(ready,1.0%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:06:54 ago, cause: software
Last software reset at 2022-09-18 10:58, reason: User, GCodes spinning, available RAM 12968, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 26.1, current 26.7, max 27.6
Supply voltage: min 12.3, current 12.4, max 12.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 3278 queued, 3278 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: over temperature warning, over temperature shutdown, phase A short to ground, phase B short to ground, standstill, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2022-09-18 11:05:18
Cache data hit count 4294967295
Slowest loop: 9.98ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 3, maxWait 43059ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 10, completed 10, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 202.25ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.26
  WiFi MAC address 2c:3a:e8:0b:09:1f
  WiFi Vcc 3.43, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 23752
  WiFi IP address 192.168.1.116
  WiFi signal strength -59dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 0 0 0 0 0 0 0 0

@phaedrux I tested now the old motors and I got the same error...

@phaedrux I'm using a 12V 33A psu, specifications of the motor: https://www.gotronic.fr/pj-451.pdf

@phaedrux hello, thank you very much for your reply!

This is a new build, but the board was used before in another printer with different motors, it's not new.

To verify the phases I used a multimeter, if I get resistance between 2 wires, that belong to the same phase, no continuity = different phase.

If I disconnect all the motors and I try to home x and y I get the same error

Hello. When I try to home for the first time x and y axis, I get '' motor phase A/B disconnected reported by <all> drivers''. I controlled crimps, connections (phases are connected in the right mode, I used the duet's wiki instructions), resistance of motors with a multimeter and everything seems good. I have a duet 2 wifi with 3.3 firmware version, a cartesian printer and using 42byghm810 stepper motor. What could I do to solve the error?

this is a part pf my config.g:

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E100.00 ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X1440 Y1440 Z1440 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X-33 Y-10 Z0 S1 ; set axis minima
M208 X220 Y220 Z240 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-35 Y5 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X20:200 Y20:200 S40 ; define mesh grid

@jay_s_uk hello! removed it, thank you very much!

Hello, I'm using a duet 2 wifi board with the E1 driver burned. I don't use the E1 for my printer, but i get "short to ground reported by driver 4" error and the driver heats up... I tried to use "M569 P4 R-1", the error stopped appearing but the driver still heats up. How could I solve?