Posts made by Smedley

M115
RepRapFirmware Duet 2 Wifi 3.0, Duet WiFi 1.02
M552
Wifi module is being started
M552 S0
ok
M587 S"DD-5" P"12345678"
Error: Failed to add SSID to remembered list
M552 S1
Turn off the current Wifi mode before selecting a new one

install WDC

@Phaedrux
Thank you I found a wire crossed.

Thanks to all that helped me. Greatly appreciate all the help.

Dave

That is a microswitch.

The M203 I messed it up cannot get it back to the 500 it was set to.

@Smedley
If I run any HOME command I have to do a EMERGENCE STOP. Is that resting M122 and not able to see the results.

The end stop switches never stop the motor. I always have to use the emergency stop.

@Phaedrux M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6J1FA-3SN6R-KSFLR
Used output buffers: 3 of 24 (16 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93184 of which 0 recycled
Exception stack ram used: 272
Never used ram: 11904
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3736) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:08:01 ago, cause: power up
Last software reset at 2020-07-28 19:05, reason: Heat task stuck, spinning module Platform, available RAM 11516 bytes (slot 2)
Software reset code 0x40a0 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f80f BFAR 0xe000ed38 SP 0x2000495c Task 0x4e49414d
Stack: 0044d797 00445546 6100f000 00000000 000004d9 00000000 00000000 43910000 41880000 3e178897 3e1cd04f bddcf905 3e3a3867 3e63939a 3e924c60 3c3ebcf3 397a8e49 c0a00000 00000000 60000010 20003258 20008a10 0044d797
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 36.9, current 37.4, max 37.5
Supply voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-07-28 19:19:06
Cache data hit count 1475307095
Slowest loop: 5.12ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.17ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 1
  WiFi firmware version 1.23
  WiFi MAC address dc:4f:22:6e:6c:38
  WiFi Vcc 3.39, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 23648
  WiFi IP address 10.0.0.88
  WiFi signal strength -62dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

@JoergS5
If I run M112 I lose my connection.

I can run M503 but not M112

@JoergS5
ok

@Phaedrux
can not upload moves to large.

If I start it from the middle it just runs to the switch and keeps going.

If I start at the far end it will run to the end switch and bounce and then come back to switch and keeps going.

@Phaedrux
config.g no M122
homeall.g. no M122

@Phaedrux
Ok I will. It is very flake.

@Phaedrux
I just put the X all the way from the switch. Hit home x it went to the switch move a way from the switch and the move back to the switch and did not stop. Basically it hit the switch and bounced and then went back to the switch and would not stop running the motor at the end stop.

@Phaedrux
The switch for X is on the left side and if you home x it goes to the right a couple of inches and stops. It will not move to the switch.

The Y switch is in the back. if I home Y the bed goes forward.

Before we changed HIGH to LOW they move to the switch and did not stop. Now they go away from the switch a couple of inches. And will not let me move them all the way to the switch with the Machine Movement on the screen.

X+10 will move to the right each time all the way to the end.
X-10 will move to the left only to the middle of the bed.
Y+10 will move the past the back
Y-10 will move half way to the front of the bed.

@Phaedrux

Now X and Y move a couple of inches and stop. They do not go to the end stop switch. Each time I run home all they stop in a different place each time. I do a EMERGENCY STOP so Z does not hit the bed. If I run home all they will move a couple of inches from were they stopped for the last time I ran home all.

The Z comes down all the way to the bed. I under stand the Z is not set yet.

I was referring to the test above I was asked to run from the MODERATOR.
That is why the wires were plugged in for the Z stop.

I am sorry for the confusion. Did not realize I was working with two different people trying to help me.

x and y are not working. The test proved that they are wired correctly and tripping the board.

Before the test you asked for I don't have the Z switch hooked up. Are you saying the BLTouch gets weird to the Z end stop pins.
Why are the X and Y not working.

Thank You, Dave

Yes They change the LED on the board.
As for the TEST
X triggers YES
Y. triggers. YES
Z. triggers NO on the test and all the time. The LED on the board tigers with the switch.

They are wired to the OUTSIDE 2 pins.

2.05 1 (2020-02-09b1
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Mon Jul 27 2020 18:06:23 GMT-0400 (Eastern Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"CR-10" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E95.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z300.00 E1500.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S300 ; Set idle timeout

; Axis Limits
M208 X5.5 Y7.4 Z0 S1 ; set axis minima
M208 X310 Y310 Z260 S0 ; set axis maxima

; Endstops
M574 X1 Y1 S1 ; set active high endstops
M574 Z1 S2 ; set endstops controlled by probe

; Z-Probe
M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
M558 P9 H2.5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-31 Y0 Z0.6 ; set Z probe trigger value, offset and trigger height
M557 X20:215 Y20:215 S64 ; define mesh grid

; Heaters
M305 P0 T98801 B4185 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T98801 B4185 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S270 ; set temperature limit for heater 1 to 270C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H0:1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
;M591 D0 C3 P1 E1 S1 ; Turn on functionality for a filament run-out switch

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Mon Jul 27 2020 18:06:24 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 H2 Z2.5 F6000 ; lift Z relative to current position
G1 H1 X-309.5 Y-307.6 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-309.5 Y-307.6 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X51 Y20 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z2.5 F100 ; lift Z relative to current position
;G90 ; absolute positioning