Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Spawn153
    3. Posts
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 11
    • Best 0
    • Controversial 0
    • Groups 0

    Posts made by Spawn153

    • RE: Duet 2 Wifi Unresposive

      I am in the UK. Ideally I would send it to be repaired directly to Duet3D, but I don't think that is possible as this wouldn't be considered a warranty repair. I also don't see anyone UK based in that forum post.

      Maybe if an Admin sees this post they could help?

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • RE: Duet 2 Wifi Unresposive

      I have read through that post, would you be willing to have a go at it? Or would you suggest I just replace it?

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • RE: Duet 2 Wifi Unresposive

      Ahh, not something I'm equipped to do. Is there somewhere I can send it for the repairs to be done? Or would it be beyond economic repair at this point?

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • RE: Duet 2 Wifi Unresposive

      I'd say normal warm up, nothing is too hot to touch.

      Unfortunately I cannot get anything to show up in device manager, not even a Bossa port 😞

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • RE: Duet 2 Wifi Unresposive

      Hi, thanks for the response. I saw a similar issue on another thread and have removed U2 and tested the board by applying 3.3v via an endstop connector. which causes the wifi module to light up, along with diag (fully bright now but doesn't turn off), the 3.3v. Both the wifi module and microcontroller warm up but I have not got anything showing up on the PC when connected to USB still.

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • Duet 2 Wifi Unresposive

      Hi,
      While plugging in the ir sensor, I failed to turn off the device and I believe there may have been a short as now I cannot access the board through windows and have gone through https://duet3d.dozuki.com/Wiki/What_to_do_if_your_Duet_won't_respond without any success. I did notice that U2 is heating up when powered. The SD card that was in use at the time is also broken and the diag light comes on dimly red when the device is powered by usb along with 2 other red LEDs.

      IMG_20200529_091145.jpg

      Is there a way to resurrect the board?

      posted in Duet Hardware and wiring
      Spawn153undefined
      Spawn153
    • RE: Unable to connect to PanelDue, not showing in Windows

      Is there anything else I can do or am I now waiting for an admin to confirm a warrenty return?
      Thanks all.

      posted in My Duet controlled machine
      Spawn153undefined
      Spawn153
    • RE: Unable to connect to PanelDue, not showing in Windows

      I have tried all you have suggested and nothing has changed. Nothing is getting hot and I cannot find any shorts.
      Thanks.

      posted in My Duet controlled machine
      Spawn153undefined
      Spawn153
    • RE: Unable to connect to PanelDue, not showing in Windows

      @samlogan87 yes I have, unfortunately none of that worked.

      posted in My Duet controlled machine
      Spawn153undefined
      Spawn153
    • RE: Unable to connect to PanelDue, not showing in Windows

      I've been through all of that and I still have nothing showing up ☹

      posted in My Duet controlled machine
      Spawn153undefined
      Spawn153
    • Unable to connect to PanelDue, not showing in Windows

      Hi,
      I bought my Duet 2 Wifi back in March from E3D and have been using it without much issue since. Today I went to print something and couldn't connect with the PanelDue. I decided to connect the board to my PC and even with nothing but USB connected I get nothing in device manager and can't connect to it via YAT or Bossa as the troubleshooting guides say. I have checked the SD card and there are no issues there. When I plug in the USB I get 4 lights, the green 3.3v led, 5v, diag and the led between the USB and reset button. Is there anything else I should try?
      Thanks

      posted in My Duet controlled machine
      Spawn153undefined
      Spawn153