Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. synergy41
    • Profile
    • Following 0
    • Followers 1
    • Topics 27
    • Posts 117
    • Best 0
    • Groups 0

    synergy41

    @synergy41

    0
    Reputation
    10
    Profile views
    117
    Posts
    1
    Followers
    0
    Following
    Joined Last Online

    synergy41 Unfollow Follow

    Latest posts made by synergy41

    • Z offset adjustment impossible

      Hi all
      I hope I would find help among you. I just changed my heating heads and I am unable to adjust the Z offset.
      My printer is a delta equip with the heating head Revo six from e3d I have an original Bl touch.
      Here is the procedure I apply: First I put the Z at 0.00 in the Bed file on line G31. I then launch M561 M208 S1 Z-3 and the M564 S0 command.

      After I lower my nozzle to make it touch on a wedge of 0.15 place on my tray when the nozzle is well placed I enter G92 Z0 to define Z = 0.

      Then I go up the nozzle to 30mm and I launch the G30 S-1 command to probe the bed. There I look at the value and enter it in the Bed file at the line "G31 P500 X0 Y25 Z2.562"

      Then I launch an automatic calibration with the G32 command, following I launch the M665 and M666 command and finally M500.

      But when I run a print my nozzle is about 3mm above the tray.

      I attach my conf and bed file.

      Can you tell me what I am doing wrong.
      Thank you.
      config .g bed.g

      posted in General Discussion
      synergy41
      synergy41
    • RE: Temperature setting gone.

      @dc42
      Thank you, that was right.
      It's passing something weird then during the update to 3.3

      posted in General Discussion
      synergy41
      synergy41
    • RE: Temperature setting gone.

      Hello, no one can help me

      posted in General Discussion
      synergy41
      synergy41
    • RE: Temperature setting gone.

      @phaedrux

      I have an extruder and heater EV6

      here is the M122

      08/02/2022, 19:08:54	M122
      === Diagnostics ===
      RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
      Board ID: 08DDM-9FAM2-LW4SD-6J9FL-3SJ6J-KJZ7Y
      Used output buffers: 3 of 24 (12 max)
      === RTOS ===
      Static ram: 23876
      Dynamic ram: 74368 of which 68 recycled
      Never used RAM 16104, free system stack 134 words
      Tasks: NETWORK(ready,13.0%,237) HEAT(delaying,0.0%,330) Move(notifyWait,0.1%,305) MAIN(running,86.2%,503) IDLE(ready,0.7%,29), total 100.0%
      Owned mutexes: WiFi(NETWORK)
      === Platform ===
      Last reset 00:02:18 ago, cause: power up
      Last software reset at 2022-02-06 20:59, reason: User, GCodes spinning, available RAM 16104, slot 2
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
      Error status: 0x00
      Aux0 errors 0,0,0
      Step timer max interval 0
      MCU temperature: min 14.1, current 22.3, max 22.6
      Supply voltage: min 24.2, current 24.4, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
      Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
      Driver 0: position 70738, standstill, SG min/max 0/118
      Driver 1: position 70738, standstill, SG min/max 0/130
      Driver 2: position 70738, standstill, SG min/max 0/143
      Driver 3: position 0, standstill, SG min/max not available
      Driver 4: position 0, standstill, SG min/max not available
      Driver 5: position 0
      Driver 6: position 0
      Driver 7: position 0
      Driver 8: position 0
      Driver 9: position 0
      Driver 10: position 0
      Driver 11: position 0
      Date/time: 2022-02-08 19:08:53
      Cache data hit count 4294967295
      Slowest loop: 11.14ms; fastest: 0.16ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Storage ===
      Free file entries: 10
      SD card 0 detected, interface speed: 20.0MBytes/sec
      SD card longest read time 3.3ms, write time 0.0ms, max retries 0
      === Move ===
      DMs created 83, maxWait 106475ms, bed compensation in use: mesh, comp offset 0.000
      === MainDDARing ===
      Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === AuxDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP is idle in state(s) 0
      Telnet is idle in state(s) 0
      File is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger is idle in state(s) 0
      Queue is idle in state(s) 0
      LCD is idle in state(s) 0
      Daemon is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 15.66ms; fastest: 0.00ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
      HTTP sessions: 1 of 8
      - WiFi -
      Network state is active
      WiFi module is connected to access point 
      Failed messages: pending 0, notready 0, noresp 0
      WiFi firmware version 1.26
      WiFi MAC address 5c:cf:7f:ee:6a:e7
      WiFi Vcc 3.40, reset reason Turned on by main processor
      WiFi flash size 4194304, free heap 25512
      WiFi IP address 192.168.1.18
      WiFi signal strength -66dBm, mode 802.11n, reconnections 0, sleep mode modem
      Clock register 00002002
      Socket states: 0 0 0 0 0 0 0 0
      

      M98 P"config.g"

      08/02/2022, 19:10:10	M98 P"config.g"
      HTTP is enabled on port 80
      FTP is disabled
      TELNET is disabled
      Error: in file macro line 34 column 19: M350: array too long, max length = 0
      Error: in file macro line 35 column 27: M92: array too long, max length = 0
      Error: in file macro line 36 column 34: M566: array too long, max length = 0
      Error: in file macro line 37 column 37: M203: array too long, max length = 0
      Error: in file macro line 38 column 34: M201: array too long, max length = 0
      Error: in file macro line 39 column 34: M906: array too long, max length = 0
      Error: Sensor number out of range
      Error: bad drive number
      Error: Tool 0 not found
      Error: bad drive number
      Error: Tool 1 not found
      Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
      Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 277C
      

      thank you for your help

      posted in General Discussion
      synergy41
      synergy41
    • RE: Temperature setting gone.

      no one can help me. I just made an update, before it worked very well. I attach my config file.

      config.g

      ; Configuration file for Duet WiFi (firmware version 1.21)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v2 on Sun Mar 17 2019 11:25:52 GMT+0100 (heure normale d’Europe centrale)
      
      
      ; ----------------------------------------------------------------------------------------------------------------------------------------------
      ; General preferences
      ; ----------------------------------------------------------------------------------------------------------------------------------------------
      G90                                                ; Send absolute coordinates...
      M83                                                ; ...but relative extruder moves
      M665 R160.00 L400.00 H520.00 B140.00  ;M665 R160 L400 B150 H520; Set delta radius, diagonal rod length, printable radius and homed height H500
      M666 X0 Y0 Z0                                      ; Put your endstop adjustments here, or let auto calibration find them
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Network
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M550 P"LittleMonsterWifi"                                   ; Set machine name
      M552 S1                                            ; Enable network
      ;M587 S"Livebox-2AF2" P"........................." ; Configure access point. You can delete this line once connected
      M586 P0 S1                                         ; Enable HTTP
      M586 P1 S0                                         ; Disable FTP
      M586 P2 S0                                         ; Disable Telnet
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Drives
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M569 P0 S1                                         ; Drive 0 goes forwards
      M569 P1 S1                                         ; Drive 1 goes forwards
      M569 P2 S1                                         ; Drive 2 goes forwards
      M569 P3 S1                                         ; Drive 3 goes forwards
      M350 X16 Y16 Z16 E16 I1                            ; Configure microstepping with interpolation
      M92 X80.00 Y80.00 Z80.00 E427.190                  ; Set steps per mm
      M566 X1200.00 Y1200.00 Z1200.00 E1200.00           ; Set maximum instantaneous speed changes (mm/min)
      M203 X19980.00 Y19980.00 Z19980.00 E3600.00        ; Set maximum speeds (mm/min)
      M201 X1000.00 Y1000.00 Z1000.00 E1000.00           ; Set accelerations (mm/s^2)
      M906 X1000.00 Y1000.00 Z1000.00 E800.00 I60        ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30                                            ; Set idle timeout
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Axis Limits
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M208 Z0 S1                                         ; Set minimum Z
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Endstops
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M574 X2 S1 P"xstop"                                ; ok Set active high endstops
      M574 Y2 S1 P"ystop"                                ; ok Set active high endstopS
      M574 Z2 S1 P"zstop"                                ; ok Set active high endstops
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Z-Probe
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M558 P9 C"^zprobe.in+zprobe.mod" H5 F300 T3000    ; Set Z probe type to bltouch and the dive height + speeds H10
      M950 S0 C"exp.heater3"                             ; create servo pin 0 for BLTouch
      G31 P500 X0 Y25 Z0.00                             ; Set Z probe trigger value, offset and trigger height 2.45; 2.658
      M557 R140 S25                                      ; Define mesh grid
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Heaters
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
      M140 H0 P0                                         ; resets the temperature limit for the heater to the default for bed heaters
      M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
      M307 H0 B0 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
      M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700  ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
      M143 H1 S280                                       ; set temperature limit for heater 1 to 280C
      ;M307 H1 A437.1 C302.4 D0.6 S1.00 V24.3 B0         ; PID tuning ed3 v6 buse 0,4
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Fans
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M950 F0 C"fan0" Q500                              ; create fan 0 on pin fan0 and set its frequency FAN IMPRESSION
      M106 P0 S0 H-1                                    ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500                              ; create fan 1 on pin fan1 and set its frequency FAN BUSE
      M106 P1 S1 H1 T45                                 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"fan2" Q500                              ; create fan 2 on pin fan2 and set its frequency FAN BOITIER MCU
      ;M106 P2 S0 H-1                                   ; set fan 2 value. Thermostatic control is turned off
      M106 P2 F100 L0.4 B0.5 T33:40 H100:101:102        ; Set fan 2 Duet case fan. Turns on when the MCU temperature (virtual heater 100)
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      ; Tools
      ; -----------------------------------------------------------------------------------------------------------------------------------------------
      M563 P0 D0 H1					                  ; Define tool 0
      G10 P0 S0 R0					                  ; Set tool 0 operating and standby temperatures
      
      ;*** If you have a single-nozzle build, comment the next 2 lines
      M563 P1 D1 H2					                  ; Define tool 1
      G10 P1 S0 R0					                  ; Set tool 1 operating and standby temperatures
      M579 X0.996 Y0.993 Z1.00                          ; scaling factor for Cartesian cords x1.01266 Y1.00908 X0.99453
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      ; Automatic saving after power loss is not enabled
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      ; Custom settings are not configured
      
      M575 P1 B57600 S1; panel due
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      ; Miscellaneous
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      G29 S1
      M501                                             ; Load saved parameters from non-volatile memory
      ; ------------------------------------------------------------------------------------------------------------------------------------------------
      
      
      posted in General Discussion
      synergy41
      synergy41
    • RE: Temperature setting gone.

      @phaedrux Here is a picture. Yes I made an update recently.
      Little monster.png

      posted in General Discussion
      synergy41
      synergy41
    • Temperature setting gone.

      Hello everyone,
      the display of the temperature setting disappeared from the display panel on my computer.
      do you have an idea.
      Thank you.

      posted in General Discussion
      synergy41
      synergy41
    • RE: M550 no longer works since RC11

      it works again now. I just deleted M550 and reinstalled it. Thanks for all you do.

      posted in Beta Firmware
      synergy41
      synergy41
    • M550 no longer works since RC11

      Good morning all
      I just upgraded to RRF 3.01-RC11, DWC 2.1.6. Since then, I have a problem with M550, I no longer have the name of my machine displayed, but my P.I.address do you have an idea.

      config.g

      posted in Beta Firmware
      synergy41
      synergy41
    • RE: Bed is working more since the update

      @dc42 said in Bed is working more since the update:

      Please read the upgrade notes for RC10.

      Thank you my friend, you are great. I had not read this.
      Solved now

      posted in General Discussion
      synergy41
      synergy41