Posts made by Threevee

No problem for me Ill just input the URL on all the devices I usually use. Thanks for the helpful response.

So I have set up a Sannce I21AG IP cam and managed to get it all working in DWC (including fixing the port number so it doesn't change every time you turn the thing off!)
Very happy with the result however when I try to access the DWC on any other computer the URL for the IP cam is missing or is kept at whatever it was the last time i used that device. Is this normal behaviour? Does this mean I have to enter the URL every time i open DWC in a new computer?

Zero. Thanks for that ill give it a go tonight!

@Threevee:

G31 P500 X0 Y0 Z2.5
I bet this is the problem. Z should be 0 i think

Nah that didn't do it.

G31 P500 X0 Y0 Z2.5
I bet this is the problem. Z should be 0 i think

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool on Thu Mar 15 2018 17:14:58 GMT+0000 (GMT)
G91 ; relative positioning
G1 Z5 F6000 ; lift Z relative to current position
G1 S1 Z-185 F1800 ; move Z down until the switch triggers
G92 Z0 ; set Z position to trigger height

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool on Thu Mar 15 2018 17:14:58 GMT+0000 (GMT)
G91 ; relative positioning
G1 Z5 F6000 ; lift Z relative to current position
G1 S1 X-205 Y-205 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y5 F6000 ; go back a few mm
G1 S1 X-205 Y-205 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 S1 Z-185 F1800 S1 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z2.5 ; set new Z position
;G1 Z5 F100 ; uncomment this line to lift the nozzle after homing

The whole gantry comes down too far and subsequently nozzle and everything else pushes the bed down on its springs. Its a regular microswitch end stop no Z probe as yet.

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Mar 15 2018 17:14:58 GMT+0000 (GMT)

; General preferences
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves

; Network
M550 PWendell ; Set machine name
M551 P ; Set password
M552 S1 ; Enable network
M587 S"" P"" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X128 Y128 Z128 E16 I0 ; Configure microstepping without interpolation
M92 X640 Y640 Z3200 E200 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z1200 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z100 E5000 ; Set accelerations (mm/s^2)
M906 X855 Y855 Z855 E855 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X200 Y200 Z180 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 Z1 S0 ; Set active low endstops
M558 P0 H5 F120 T6000 ; Set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X25:175 Y25:175 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
T0 ; Select first tool

Recently finished installing the duet and testing all the things in my wanhao i3 plus. Homing works great heaters work great and everythings reading correctly - however whenever i start my first print the Z axis comes down too far and snaps off the Z endstop. I have confirmed the Z stop is working correctly and it does home correctly but starting a print just snaps the stop off time and time again. Anybody have any ideas what could be causing this?

Excellent responses thanks very much ill keep these in mind when it comes to the build and leave the BL touch out for the time being till the new firmware update comes out and get it set up then.

Hello all new to the forum. Currently eagerly awaiting the postman with my new duet wifi. I am planning to upgrade my wanhao i3 Plus to a duet mainboard. Total overkill for this purpose but I have future plans for this thing. I managed to kill the extruder driver on the melzi board that came with the printer when changing over to the e3d titan aero hotend/extruder and want to make sure that i don't do the same to the duet.
A few questions.
1/ When I'm installing the hardware for the first time should I set the stepper motor pot down to the minimum and then gradually bring it up? I suspect the initial cause of failure was me unplugging and plugging in the stepper with the power on (stupid I know now but didnt at the time.)
2/The power supply I have is also 24V will this need any adjustment before the first power on of the board?
3/ I have a BLtouch I had planned to set up on this printer would you recommend using this or the IR sensor the board seems to be very compatible with? (I plan on using glass bed mostly coated with PEI or buildtak material depending)
4/ Would you recommend initially setting up the printer with the Z endstop still in place or should I go straight for the bed compensation setup and forgo the Z endstop.
Thanks for any advice