it does not. i will contact filastruder then. thanks.

my smart effector is not triggering. on power up it flashes twice as it should, i have checked the wiring and i have continuity on all four wires, and i have also removed my nimble from it.
anything else i should be checking?

M555 P2 ; Set firmware compatibility to look like Marlin

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R106.3 L215.82 B102 H260 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them
M208 Z-0.1 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S0 ; Set active low endstops
M558 P5 R0.4 F1000 ; Set Z probe type to effector, the axes for which it is used and the dive height + speeds
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R85 S20 ; Define mesh grid

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation
M92 X100 Y100 Z100 E2400 ; Set steps per mm
M566 X36000 Y36000 Z36000 E36 ; Set maximum instantaneous speed changes (mm/min)
M203 X1080000 Y1080000 Z1080000 E1200 ; Set maximum speeds (mm/min)
M201 X3000 Y3000 Z3000 E120 ; Set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
;M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
;M301 H1 S1.00 P10 I0.1 D200 T0.4 W180 B30
M305 P0 X201 ; Set thermistor bed
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor hotend
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PMagKossel ; Set machine name
M552 S1 ; Enable network
M587 S"NETGEAR81" P"o8346969" I192.168.1.101 J192.168.1.254 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured

the engine enamel doesn't tell you to cure it because the the heat from your headers or the engine block (what ever you painted) actually cures it. you may get the same effect by painting the pei and after its dry placing it on your heat bed and letting it sit on there at temp for an hour or so.