I cant get my spindle to turn on.
Fusion gives me this command

M3 S3000

It says No P parameter and no active tool with spindle

M3 P0 S3000

This works where do i tell fusion 360 to put that before every M3 command

This is my config file i tried a few things but i dont really understand the system

; Configuration file for RepRapFirmware on Duet 3 Main Board 6XD
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.5 on Fri Nov 08 2024 16:48:28 GMT+0100 (Mitteleuropäische Normalzeit)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Duet 3" ; set hostname

; Network
M552 P192.168.2.1 S1 ; configure Ethernet adapter
M553 P255.255.255.0 ; set netmask
M554 P192.168.2.1 ; set gateway
M586 P1 S1 ; configure FTP
M586 P0 S1 ; configure HTTP

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; External Drivers
M569 P0.0 S0 R0 T5:5:10:0 ; driver 0.0 goes backwards and requires an active-low enable signal (X axis)
M569 P0.1 S1 R0 T5:5:10:0 ; driver 0.1 goes forwards and requires an active-low enable signal (X axis)
M569 P0.2 S1 R0 T5:5:10:0 ; driver 0.2 goes forwards and requires an active-low enable signal (Y axis)
M569 P0.3 S1 R0 T5:5:10:0 ; driver 0.3 goes forwards and requires an active-low enable signal (Y axis)
M569 P0.4 S1 R0 T5:5:10:0 ; driver 0.4 goes forwards and requires an active-low enable signal (Z axis)

; Axes
M584 X0.2:0.3 Y0.0:0.1 Z0.4 ; set axis mapping
M350 X16 Y16 Z16 I0 ; configure microstepping without interpolation
M92 X35.56 Y35.56 Z800 ; configure steps per mm
M208 X0:560 Y0:900 Z0:140 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
M203 X3000 Y3000 Z180 ; set maximum speeds (mm/min)
M201 X250 Y250 Z20 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Endstops
M574 X1 P"!io1.in" S1 ; configure X axis endstop
M574 Y1 P"!io0.in" S1 ; configure Y axis endstop
M574 Z2 P"!io2.in" S1 ; configure Z axis endstop

; Spindles
M950 R0 C"vfd" Q2000 L0:19200 ; configure spindle #0

; Tools
M563 P1 D0 H1 R0 ; create tool #0
M568 P1 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M453 ; select CNC mode
T1 P0 ; select first tool
M3 P0 S0

I want to use Tool1 for everything i dont understand currently how this number thing works. I set in fusion 360 all my tools to number one and just do different gcode files when i need to switch

@droftarts i dont really know why but i cant get the spindle over 10k rpm

I did M3 P0 S3000 and then tried to put 19200rmp in the dashboard but it only go to 10k rpm. Are there other limit factors then the config file?

And thx for all the help

@droftarts

This is how i wired it also didnt worked.

M950 C"vfd" Q2000 L0:19200 ; configure spindle #0

@droftarts if the output is only 3.3v a converter would also not work right? maybee this is the problem?

@droftarts I have the green one as descripted. I checked it again. The jumper is at 5volts. It has 24v input, And i go from io4.out and oi4 ground pin to the pwm inputs.
I meassured 0v at the other side on the converter. I hope this helps

@droftarts

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.5.3 (2024-09-18 11:27:56) running on Duet 3 MB6XD v1.0 (standalone mode)
Board ID: 08DLM-956DA-M24S4-7JKD4-3SJ6N-KBJQU
Used output buffers: 1 of 40 (18 max)
Error in macro line 58 while starting up: exactly one of EFHJPSR must be given
=== RTOS ===
Static ram: 153760
Dynamic ram: 118264 of which 184 recycled
Never used RAM 70928, free system stack 210 words
Tasks: NETWORK(1,ready,33.9%,182) ETHERNET(5,nWait 7,0.1%,322) HEAT(3,nWait 6,0.0%,360) Move(4,nWait 6,0.0%,335) CanReceiv(6,nWait 1,0.0%,939) CanSender(5,nWait 7,0.0%,334) CanClock(7,delaying,0.0%,336) MAIN(1,running,65.9%,128) IDLE(0,ready,0.1%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:03:34 ago, cause: power up
Last software reset at 2024-11-08 16:52, reason: User, Gcodes spinning, available RAM 70856, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 8.7, current 23.6, max 23.6
Supply voltage: min 23.8, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/48/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2024-11-08 17:46:09
Slowest loop: 6.82ms; fastest: 0.06ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 1073, received 0, lost 0, errs 1009044, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 1073/0/0
Tx timeouts 0,0,1072,0,0,0 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 6.24ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 1 0 0
Socket states: 5 2 2 2 2 2 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0

code_text

; Configuration file for RepRapFirmware on Duet 3 Main Board 6XD
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.5 on Fri Nov 08 2024 16:48:28 GMT+0100 (Mitteleuropäische Normalzeit)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Duet 3" ; set hostname

; Network
M552 P192.168.2.1 S1 ; configure Ethernet adapter
M553 P255.255.255.0 ; set netmask
M554 P192.168.2.1 ; set gateway
M586 P1 S1 ; configure FTP
M586 P0 S1 ; configure HTTP

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; External Drivers
M569 P0.0 S1 R0 T5:5:10:0 ; driver 0.0 goes forwards and requires an active-low enable signal (X axis)
M569 P0.1 S0 R0 T5:5:10:0 ; driver 0.1 goes backwards and requires an active-low enable signal (X axis)
M569 P0.2 S1 R0 T5:5:10:0 ; driver 0.2 goes forwards and requires an active-low enable signal (Y axis)
M569 P0.3 S1 R0 T5:5:10:0 ; driver 0.3 goes forwards and requires an active-low enable signal (Y axis)
M569 P0.4 S1 R0 T5:5:10:0 ; driver 0.4 goes forwards and requires an active-low enable signal (Z axis)

; Axes
M584 X0.0:0.1 Y0.2:0.3 Z0.4 ; set axis mapping
M350 X16 Y16 Z16 I0 ; configure microstepping without interpolation
M92 X35.56 Y35.56 Z800 ; configure steps per mm
M208 X0:900 Y0:560 Z0:140 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
M203 X3000 Y3000 Z180 ; set maximum speeds (mm/min)
M201 X250 Y250 Z20 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Endstops
M574 X1 P"!io0.in" S1 ; configure X axis endstop
M574 Y1 P"!io1.in" S1 ; configure Y axis endstop
M574 Z2 P"!io2.in" S1 ; configure Z axis endstop

; Heaters
M950 H0 C"out0" T0 ; create heater #0
M143 H0 P0 T0 C0 S140 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"out1" T1 ; create heater #1
M143 H1 P0 T1 C0 S285 A0 ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Spindles
M950 C"io4.out" Q500 L60:19200 ; configure spindle #0

; Tools
M563 P0 D0 H1 R0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M453 ; select CNC mode
T0 ; select first tool

Hello
I use the duet3d 6XD.
If i want to configure it there is only the option for io4.out io5.out and io7.out.
But these are not the pwm outputs that are descripted in the documentation. I tried to write in the config file "out4" insteat also didnt worked.

And even if i set my max spindle speed to 19200rpm in the config it doesnt want to go over 10k rpm in the interface. I dont have a voltage tester that is capable for pwm so i wanted to go 100percent to meassure it normally