@dc42 Thank you for catching that I corrected M305.
I found the cause of my problem, the heat block was tight against the heatsink. I went back and looked at the Titan Aero assembly instructions and saw a picture of it ( Thank God for pictures).
They should put something in their instructions for dummies like me.
Everything auto tuned perfectly and have it set up in the firmware.
Now on to the rest of the setup, Thanks for being here for us newby's
Sorry I didn't type that correctly.
M303 H1 P1 S240
M303 H1 S240 Firmware version is 1.20
@phaedrux I do have a sock on it and no part cooling fan yet
This is what is in the heater section of my Config.g file ; Thermistors and heaters
;*** You can use S and B parameters to define the parameters of the thermistors you are using
M305 P0 T100000 B4388 R4700 H0 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
M305 P1 T100000 B4725 R4700 H0 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction
M305 P2 T100000 B3974 R4700 H0 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction
M301 H1 P10 I0.10 D100 T0.50 S1.5 ; PID settings for extruder 0
M301 H2 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 1
M570 S12000 ; Increase to allow extra heating time if needed
M307 H0 A199.0 C962.6 D4.5 B0
M307 H1 A406.3 C166.4 D10.3 B0
I am pulling my hair out with this and sure it must be something wrong in the gcode. My hotend does not heat up vast fast therefore i get "Auto tune cancelled because target temperature was not reached". I have checked the heater cartridge it is 4.3 ohms which according to my searches is correct. I have 12.3 volts constantly to the cartridge.
My thermister matches within 2deg of the reading from my Klein meter and thermister.
I have even tried another heat cartridge and thermister with the same results.
Could someone please enlighten me as to what Iam doing wrong. I have Googled and read until my eyes are poping out.
Any help in a direction to fix this would be greatly appreciated.
Thank you in advance
I am sorry, I figured it out today. My lead screws were way out of adjustment and binding the build plate.
All stepper motors work good. Now on to getting the end switches working lol.
Sorry to take up your time.
I am using a Duet wifi, upper right corner of the wiring diagram it says Drive 2 then you have option A - 1- Z motor and Option B- 2-Z motors in series .
Hold on I just noticed the wiring color connections on the board are not the same as on my steppers. Let me change that and will get back to you.
Thanks
They are Model 42HD4027-01 Rated currant 1.5A Step angle 1.8 Voltage 3.3 Holding torque 400mN
set currant to 1a,connected to Drive 2 option B
I have a d-bot machine which I think is a core X-Y. X and Y work great. The Z axes actually jogs from one side to the other. In other words when I move the Z axes one stepper turns then the other turns,they both don"t turn at the same time. I have searched for answers but have found nothing.
Again Thank you for any help.
Thank you that fixed it, I had my SSID wrong.
Thanks again for your time and help. Now to get my machine all setup.
This is what I get,
RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23 <lf><lf>Executing config.g…WiFi module is disabled <lf>Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 275C. <lf><lf>Done! <lf>RepRapFirmware for Duet WiFi is up and running. <lf>WiFi module started <lf>Error: Temperature readi
M552 S0 <lf>ok <lf>M552 S1 <lf>ok <lf>WiFi reported error: no known networks found <lf>Wifi module is idle</lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf>
I went through the out of step instructions and this is what I have now. Still no wifi as far as I can tell.
=== Diagnostics === <lf>Used output buffers: 1 of 32 (32 max) <lf>=== Platform === <lf>RepRapFirmware for Duet WiFi version 1.20 running on Duet WiFi 1.0 <lf>Board ID: 08DDM-9FAM2-LW4SD-6JKF2-3SJ6R-KLZRY <lf>Static ram used: 15448 <lf>Dynamic ram used: 99320 <lf>Recycled dynamic ram: 4016 <lf>Stack ram used: 3576 current, 4648 maximum <lf>Never used ram: 7640 <lf>Last reset 00:09:01 ago, cause: power up <lf>Last software reset details not available <lf>Error status: 4 <lf>Free file entries: 10 <lf>SD card 0 detected, interface speed: 20.0MBytes/sec <lf>SD card longest block write time: 0.0ms <lf>MCU temperature: min 35.7, current 36.0, max 36.3 <lf>Supply voltage: min 1.6, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0 <lf>Driver 0: ok, SG min/max not available <lf>Driver 1: ok, SG min/max not available <lf>Driver 2: ok, SG min/max not available <lf>Driver 3: ok, SG min/max not available <lf>Driver 4: ok, SG min/max not available <lf>Date/time: 1970-01-01 00:00:00 <lf>Cache data hit count 632266159 <lf>Slowest main loop (seconds): 0.151117; fastest: 0.000036 <lf>=== Move === <lf>MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0 <lf>Scheduled moves: 0, completed moves: 0 <lf>Bed compensation in use: none <lf>Bed probe heights: 0.000 0.000 0.000 0.000 0.000 <lf>=== Heat === <lf>Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 <lf>Heater 1 is on, I-accum = 0.0 <lf>=== GCodes === <lf>Segments left: 0 <lf>Stack records: 1 allocated, 0 in use <lf>Movement lock held by null <lf>http is idle in state(s) 0 <lf>telnet is idle in state(s) 0 <lf>file is idle in state(s) 0 <lf>serial is ready with "M122" in state(s) 0 <lf>aux is idle in state(s) 0 <lf>daemon is idle in state(s) 0 <lf>queue is idle in state(s) 0 <lf>autopause is idle in state(s) 0 <lf>Code queue is empty. <lf>Network state is running <lf>WiFi module is idle <lf>Failed messages: pending 0, notready 0, noresp 0 <lf>WiFi firmware version 1.20 <lf>WiFi MAC address 5c:cf:7f:a4:06:97 <lf>WiFi Vcc 3.43, reset reason Turned on by main processor <lf>WiFi flash size 4194304, free heap 19600 <lf>HTTP sessions: 0 of 8 <lf>Socket states: 0 0 0 0 0 0 0 0 <lf>Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) <lf>ok <lf>What should I do from here.
Thank you for your time</lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf>
Please forgive me if I am doing something dumb here, complete newby. I was able to upgrade firmware ok but now when I do a M552 SO I get this.
M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.20 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-12-23<lf>ok <lf>M552 SO
ok<lf>WiFi module started<lf>Error: Failed to initialise WiFi module, code -10 <lf>I have done a search on the forum but came up with nothing.
Thank you for any help</lf></lf></lf></lf></lf>
