Hello,

Thank you, I concur! I will make the changes accordingly..

Hello,

0,0 is left rear.

Hello,

My printer has had a bed leveling issue from day one. I believe it may be due to the height map probing starting at the min position or the front of the bed (y axis) and the homing at the max position or the back of the bed (with the slicer). My Y axis end stop is mounted in the max position (the back). In the slicer if I move my part to print forward toward the front (the min) of the bed the part prints to the back or the max. It seems to be inverted. Could this be causing the bed leveling to be off? How would I correct this issue?

Thank you!

Hello! I wanted to thank everyone that assisted me during two (2) of my latest builds. John you were very helpful, Thank you very much. I have attached photos of the new Xinkebot Orca 2 Cygnus with Duet Ethernet/ Panel Due 7i and the large format printer (1500mm x 1000mm x 1500mm) running a Duet Wifi and Panel Due 7i. They are both operating extremely well and the prints are amazing!!! Vernon Buchanan!!

I was wondering about that myself... I inspected all the fuses, and they all look good. Also, I cannot see any physical damage to the board. In the beginning the board was completely dead. I took a few minutes of sitting to get the lights to come back on... Initially, after the lights returned, the ethernet was working. After several times of off/on while running tests, it stopped lighting up..

I will follow your advice for the PanelDue. Thank you. I am not sure about the Main Processor temperature. I will pull out my IR gun and check it out. I did connect to Pronterface and input M564 H0 S0 with the main power on, and I got no response as far as movement from the axis. Not sure if there are other tests I could try??? Update: After plugging the PanelDue via USB into my laptop it appears to be working fine. I wish I could say the same for the Duet....

Hello, Thank you for your response! M39 brought back:

SENDING:M39
SD card in slot 0: capacity 3.90Gb, free space 3.90Gb, speed 20.00MBytes/sec, cluster size 64kb
ok T0:2000.0 /0.0 B:23.7 /0.0

My Ethernet port on the Duet no longer lights up. I am unable to get any response via ip address. M552 via Pronterface brings back:

SENDING:M552
Network is enabled, configured IP address: 0.0.0.0, actual IP address: 0.0.0.0
ok T0:2000.0 /0.0 B:23.8 /0.0

It looks as if I inadvertently inverted the positive and negative wires on BL Touch (wired to Heater 7/PWM 5). I thought I was switching the polarity for my new parts fan. Do I get a special award for such an ignorant mistake?? Should I order a new board and Panel Due now, or does someone know how I might rectify this problem??? Thank you!

Hello, My new Duet Ethernet just made a loud pop noise and all the lights went out on the board and the Panel Due 7i shut down. For a while I could not even get a light to come on. However, after waiting a bit, I was able to get the green LED 3.3v, the red LED 5v, and the red LED next to the micro usb to come on. I was then able to connect via pronterface. The M552 command showed current ip address. A minute later I was able to connect via web page. The endstop lights were on for the x and y drives. I shut down, and I unplugged them started the board back up and they turned off. I unplugged the usb and plugged it back in again. The Panel Due is lit up dimly but nothing for an interface exists. It is simply blank. Now when I try to connect via ip address I get this response "Your Duet rejected the HTTP request: page not found". I have no idea on how to proceed, can someone please direct me??? Thank you

I will make the changes, and post accordingly. Thank you!!!!!