Posts made by vucheria

undefined

@bearer
I'm not that confident in re-flashing the ESP and don't want to damage the board.
Thanks

undefined

Thank you so much guys for your support;
The board is out of warranty, but since I have no problems regarding the prints I will use it/wait for repair until it fails;
Anyways duet boards are the best, never looked back since 2018

undefined

@Phaedrux

I've tried yesterday this aproach and also tried again today with M552 commented and all M552 variants..no success,
I've also tried as suggested by @dc42 in other posts with and without VIN power, without endstops connected or BL-Touch
When I use the M997 S1 the wifi led blinks as if starting up but after a few seconds it is turning off.

please see below today's log from YAT

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1
M552
WiFi module is disabled
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F23T0-6JKDL-3S86R-KWBDF
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93160 of which 396 recycled
Exception stack ram used: 312
Never used ram: 11492
Tasks: NETWORK(ready,1360) HEAT(blocked,1232) MAIN(running,3728) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:05:06 ago, cause: power up
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 12300 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 36.4, current 41.9, max 42.1
Supply voltage: min 24.3, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 606309682
Slowest loop: 1.67ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1001.18ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

WiFi -
Network state is disabled
WiFi module is disabled
Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
Socket states: 0 0 0 0 0 0 0 0

M997 S1
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error

M997 S0
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1
M552
WiFi module is disabled
M552 S0

WiFi module started
M997 S1
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error

M552 S-1

M552
WiFi module is disabled
M552 S1

WiFi module started
WiFi module is connected to access point v2.4GhzE, IP address 192.168.0.108
M997 S1
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error

my config file

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Dec 11 2018 03:52:52 GMT+0200 (Eastern European Standard Time)

; General preferences
G90                                                ; Send absolute coordinates...
M83                                                ; ...but relative extruder moves
M555 P1 					   ; speak the firmware
M667 S1                                            ; Select CoreXY mode

; Network
M550 P"hypercubeEvo"                                ; Set machine name
;M552 S1                                            ; Enable network
M586 P0 S1                                         ; Enable HTTP
M586 P1 S0                                         ; Disable FTP
M586 P2 S0                                         ; Disable Telnet

; Drives
M569 P0 S1                                         ; Drive 0 goes forwards
M569 P1 S1                                         ; Drive 1 goes forwards
M569 P2 S1                                         ; Drive 2 goes forwards
M569 P3 S0                                         ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1                            ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E521                  ; Set steps per mm
M566 X1000.00 Y1000.00 Z150 E1000                 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z300.00 E700            ; Set maximum speeds (mm/min)
M201 X4000.00 Y4000.00 Z250.00 E4000                ; Set accelerations (mm/s^2)
M906 X960.00 Y960.00 Z960.00 E1000.00 I30           ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; Set axis minima
M208 X285 Y285 Z270 S0                             ; Set axis maxima

; Endstops
M574 X2 Y2 S1                                      ; Set active high endstops

;M574 X1 Y2 S1 ; X home to max. Y home to max. Normally Closed limit switches.
;M574 Z1 S2 ; Define Z to use Probe. Home to Min

; Z-Probe
M574 Z1 S2                                         ; Set endstops controlled by probe
M558 P9 H2 F500 T6000                             ; Set Z probe type to switch and the dive height + speeds
G31 P1000 X0 Y-30 Z0.62                              ; Set Z probe trigger value, offset and trigger height
M557 X5:285 Y5:235 S56:76                            ; Define mesh grid
M376 H15                                           ; Set bed compensation to taper off over 15mm

; Heaters
M305 P0 T100000 B4138 R4700                        ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; Set temperature limit for heater 1 to 280C

; BLTouch - Heaters
M307 H3 A-1 C-1 D-1 ; Disable the 3rd Heater to free up PWM channel

; Fans
M106 P0 S0 I0 F500 H-1                 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"e3D_V6_0.4" D0 H1                         ; Define tool 0
G10 P0 X0 Y0 Z0                                   ; Set tool 0 axis offsets
G10 P0 R60 S220                                       ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Miscellaneous
M572 D0 S0.54                                   ; Pressure advance


;use volumetric
M200 D1.75

; ############################
; 9 - RETRACTION SETTINGS
; ############################

M207 S2.3 R-0.000 F4000 T3000 Z0.0

;M207 ; echo the settings to the console to show they are applied

	; M207: Set retract length
	; Parameters
	; 	Snnn positive length to retract, in mm
	; 	Rnnn positive or negative additional length to un-retract, in mm, default zero
	; 	Fnnn retraction feedrate, in mm/min
	; 	Tnnn feedrate for un-retraction if different from retraction, mm/min (RepRapFirmware 1.16 and later only)
	; 	Znnn additional zlift/hop
	; Example: M207 S4.0 F2400 Z0.075
	; known to work M207 S2.3 R-0.000 F4000 T3000 Z0.0

; FEEDRATE CONVERSIONS
	; 20mm/s = F1200
	; 35mm/s = F2100
	; 50mm/s = F3000
	; 70mm/s = F4200
	; 100mm/s = F6000
	; 120mm/s = F7200
	; 133mm/s = F8000

undefined

@Phaedrux

Yes, followed the instructions as in the link...step by step..same error

I’ve also downgraded the firmware to 1.21 and tried to update to 2.02 with the DuetWiFiServer 1.22 and 1.23...same error; and also tried with all major releases

I will try again in the morning maybe I’ve missed something
Anyway thank you guys for support!

undefined

@bearer

The same..

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1
ok
M21 M111 P14 S1 M997 S1
SDHC card mounted in slot 0, capacity 3.98Gb
ok
Debugging enabled for modules: WiFi(14)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15)
ok
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error
ok
M997 S1
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error
ok

undefined

Help!
I usually find the solutions in the forums without the need to ask for help..but after full day of searching and trial and error I give up.

When I was trying to update the firmware from 2.03 to 2.05.1 I've noticed that my DuetWifiServer version was 1.21 but I've proceeded to install the Duet2CombinedFirmware DuetWifiServer DuetWebControl 2.0.7..everything updated only the DuetWifiServer version remained 1.21
I know that the correct DuetWifiServer version for 2.03 firmware should have been 1.23 in the first place

I've tried fallback procedures 1, 2 Installing_and_Updating_Firmware

The error that I get is when I use YAT with M997 S1 is
Trying to connect at 230400 baud: failed
Trying to connect at 115200 baud: failed
Trying to connect at 74880 baud: failed
Trying to connect at 9600 baud: failed
Error: Installation failed due to comm write error

I've also tried other suggestions offered in other posts with the same error but no success:
https://forum.duet3d.com/topic/13122/duetwifiserver-upgrade-failed-failed-due-to-comm-write-error
https://forum.duet3d.com/topic/3147/think-wifi-dont-work/18
https://forum.duet3d.com/topic/766/new-board-can-t-update-wifi-firmware/9
also tried to downgrade to 1.21 firmware and update from there to newer versions..still nothing

By the way the Duet Board v1.04 works just fine, I can connect to wiFi via web interface, I can connect from USB, I can print, etc.. but I cannot update DuetWifiServer.

Any suggestions / ideas? It is a hardware problem?

Thanks