Hello, am new here but not a newbie as such.
-
Can you post the contents of your config.g as it is currently?
Also what do you see on the PanelDue console at startup?Yes Wifi is a bit persnickety. Trying to do initial setup without a router in the mix will be a bit challenging.
-
It take 3 or 5 entries of
M552 S2 via YAT
For it to say it is doing the adhoc network
The macro is saved as a new document. I double clicked it and everything went wrong. What am I supposed to do with a macro to get it to work/be used?
I just need the FuseDeep network to go live when the machine is in use. obviously
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
everything went wrong.
What exactly does that mean?
Normally, the DuetWifi works like this. The SSID you want to connect to and the username and passwords is saved to the wifi module. Multiple SSIDs can be saved, and when the config.g is executed at startup, the wifi module is set to active with an M552 command and it will connect to whatever SSID has the best signal strength.
In your case, we want the module to stay idle at startup, and then configure ad hoc mode so we can connect to the duets network.
I don't know what you have in config.g or in the adhoc macro, so I can't say what to change.
-
...No idea what it means really...lol.
It seems to be behaving now. Am wiring up some connections then will look at config file. The adhoc macro I created, will that run automatically? Or do I need to put it somewhere special?
As you say just need fusedeep wifi from DUET 2 to come live so I can connect to use it. ideally.
Thanks. R
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
The adhoc macro I created, will that run automatically? Or do I need to put it somewhere special?
It won't run automatically. The documentation for M589 states that it will not run from config.g. So we must call it separately.
The macro you created will live in the macros folder.
To call the macro, you use M98. https://duet3d.dozuki.com/Wiki/Gcode#Section_M98_Call_Macro_Subprogram
At the end of config.g you can add
M98 P"AdHocWIFI"(assuming that's what you named it) to call the adhoc network macro. That should work I think, but I haven't tested it myself.I mentioned using G4 S# commands earlier, these are pause commands to wait a set amount of time. The wifi module needs some time to process the commands it is sent. The module needs to be in the idle mode before it can be configured and it can take a few seconds for it to switch to idle.
-
Awesome thanks.
Lot's more reading up to do.
I have my Z stepper connections labelled A+- and B+- , can I equate this to A- = A1 and A+ = A2 and similar for B?
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
I have my Z stepper connections labelled A+- and B+- , can I equate this to A- = A1 and A+ = A2 and similar for B?
I'm sorry, but I don't follow.
-
My previous Z plug is labelled A+- and B+- for the stepper coil sets.
The DUET 2 board uses 2B2A1A1B
Is 2A1A equal to A+ and A- and similarly for B; 2B1B equal to B+ and B- for the sake of wiring the new plugs?
SORTED IT!
-
End stops seem to be working.
Odd though, can only move x and y by same amount then it stops moving.
WIFI adhoc from duet2 disappears after ten minutes, even though blue led still on. irritating (this might have been me pressing main stop on screen).
Also, it has stopped asking me to restart board after a config update.
Without a full move endstop, what stops the axis moving and crashing, even with the travel length set. it does not seem to be stopping...
Plus constant wifi idle window is making screen unusable...wifi is a massive pain. How on earth do i stop it telling me it is in idle ALL of the time?
Currently tool 0 missing! (my extruder) , need to check if i removed the tool...
Help! please. Back in the morning GMT 0900 ish
(other than that, all moving and end stopping so not a bad first few hours) plus, love the simple crimps and tool. work a treat. Where can I buy multiple packs of the plugs/pins etc to make changes /mistakes etc?
R
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
Awesome thanks.
Lot's more reading up to do.
I have my Z stepper connections labelled A+- and B+- , can I equate this to A- = A1 and A+ = A2 and similar for B?
Yes.
-
Question:
If I am building the congif file via the web interface and then upload it, then edit it on the board direct...next time i do a web interface edit and upload, the other changes will be lost, no?
-
WIFI AdHoc set up:
Every time the adhoc shuts down, I have to go back to YAT and retrigger with a M552 S2 command.
There must be a way of setting this up proper, as a default?
I have added M98 p"AdHocWIFI" to last page web interface custom settings. but it does not seem to work. It should trigger my macro?
Also, am constantly getting a filename too long error now. seems to be a bug?
Help please. R
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
Question:
If I am building the congif file via the web interface and then upload it, then edit it on the board direct...next time i do a web interface edit and upload, the other changes will be lost, no?
No - (as long as you press the button that says "save"). The changes get made to the config file on the SD card.
Edit. You can't edit the configuration file "on the board direct". -
@deckingman Thanks. stumped by my extruder not showing up at all om DWC!
-
@FuseDeep said in Hello, am new here but not a newbie as such.:
@deckingman Thanks. stumped by my extruder not showing up at all om DWC!
Probably time you posted your config.g file, otherwise we can only make guesses.
-
Completely agree:
Using one laptop on the FuseDeep wifi and one connected to tinternet is cramping my style:
Will need to do the following, add another identical (2nd Y axis) stepper from a "spare"stepper driver and have it run in reverse. Would drove 04/E1 do it?
Currently no extruder showing at all, just shaded out extrude/retract in DWC page. Odd, seems to be set up OK. obviously not!
Need to have adhoc FuseDeep wifi come on automaticaly wiohtout needing USB and YAT command!
BTW, having 10 second updates has literally saved me an hour today already. Marlin used to tak 4 to 5 mins each time!
Other thing, iirc I had to up the hysteresis setting in Marlin to stop the extruder lag killing the print (or something like that), how would I do that in DWC - Do I edit a separate config type file?
config.g as below:
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.4 on Mon Dec 30 2019 11:04:01 GMT+0000 (Greenwich Mean Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"FuseDeep" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4266.67 E406.47 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E2700.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z2.00 E250.00 ; set accelerations (mm/s^2)
M906 X1350 Y1600 Z1600 E1350 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X620 Y550 Z1440 S0 ; set axis maxima; Endstops
M574 X1 Y1 Z1 S1 ; set active high endstops; Z-Probe
M558 P0 H5 F120 T3000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M140 H-1 ; disable heated bed
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M106 P0 S0 I0 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
; Custom settings
M98 P"AdHocWIFI"; Miscellaneous
M501 ; load saved parameters from non-volatile memory -
So to add a second drive to the Y axis would this work?
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 4 goes forwards (that's extruder 01 drive/4)
M584 X0 Y1 Y4 Z2 E3 ; set drive mapping (is that correct please?)Am fairly optimistic the might work...I assume I edit the installed config file and hit save. This then gets saved/updated into the DWC?
SUCCESS! Used the colon separator. it works!
-
Problem:
When I update the config file via DWC direct, it asks me to restart the board to implement.
Once the board restarts, the wifi is lost and I have to goto YAT nd find a spare com port to connect and trigger AdHoc wifi command. Also, YAT keeps complaining of no spare com ports.
This is a pain, obviously!
PS> still can't see extruder...lol Saying no tool selected. hmm.
R
-
Problem with saving config changes:
I edited the config file via the actual board wifi. Got the second stepper working on Ygreat. saved it obviously.
However, when I (again) tried to check the extruder as tool 1 (still not working) it updated the board via upload and checking the onboard congif file, my original Y stepper additions are lost.
Bit painful, how do you edit the config file and add uploads, or don't you?
How then do you back up the config file onto a laptop? A copy and paste I suppose?
Frustrating. R
-
EXTRUDER:
Heater works great and so does stat.
However the tool 0 does not extrude during printing, even though it will extrude when not printing. will do a google...says not hot enough. nut is at 220 degrees
FIXED!
