Printer stopt moving

[stienfromarden]

@Veti said in Printer stopt moving:

M204 S5000
G1 F540
G1 X411.326 Y408.547 E0.64352

did you set reprap instead of marlin in prusaslicer?

540 is 9mm/sec

Jes I did. I try to change that!

[stienfromarden]

ok, so when I choose marlin firmware in my PrusaSlic3r it moves very slow when homing before printing an then it stops, same problem as with reprap..

[Veti]

@stienfromarden said in Printer stopt moving:

When I cancel the the print I cannot issue a move with the web ui

what is the error on the console?

[stienfromarden]

This post is deleted!

[stienfromarden]

No errors on the console weirdly, but I'm also not able to cancel the print, only pause it..

[Veti]

can you issue the commands M201 till M205 and post the outputs

[stienfromarden]

I just updated the firmware, and now I have some other issues... trying to fix that first and than I will issue m201 till m205

thanks so far, keep you updated

[stienfromarden]

I get this error now

[droftarts]

From your gcode file:

M107
M104 S200 ; set temperature
G28 X0
G28 Y0
M561 ; Clear any bed transform that might be in place
G30 ; Do a single probe
M375 P"2020begin1.csv" ; Load my custom heightmap.
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
; Filament gcode
G1 E-5.00000 F3600.00000
G1 Z2.000 F18000.000
G1 X409.730 Y410.094
G1 Z0.500
G1 E8.00000 F4800.00000
M204 S5000
G1 F540
G1 X411.326 Y408.547 E0.64352
G1 X414.329 Y405.936 E1.15176

You said it stops after the probe (G30). Does it do the filament retraction? The next move after that is a Z move at F18000 (300mm/s), too fast for you Z axis.

Ian

[Veti]

@stienfromarden
its just a warning. but in the homing files change S1 to H1

[stienfromarden]

ok, got it updated now and I looks like this;

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.05 (2019-12-13b1)
WiFi Server Version: 1.23
Web Interface Version: 1.22.6

[droftarts]

Ignore those warnings for now. You can change them, in your home.g files, later, but the S is still supported in 2.05.

The "tube-marlin.gcode" file is different from the one you posted? Most likely, if the firmware is set to Marlin in PrusaSlicer, the slicer is adding the motor speed/acceleration/jerk codes. The main problem with that is that Marlin specifies these in mm/s, while RRF specifies them in mm/minute, so they are very low values for RRF.

Ian

[stienfromarden]

@droftarts

Thanks, it does the retraction! So it's probably the 300mm/s Z travel, but where do I change that?

I tried the same gcode file and now zy moved for 20cm aprox.

[Veti]

@droftarts said in Printer stopt moving:

The next move after that is a Z move at F18000 (300mm/s), too fast for you Z axis.

his config limits the max speed to Z400

[stienfromarden]

@droftarts said in Printer stopt moving:

Ignore those warnings for now. You can change them, in your home.g files, later, but the S is still supported in 2.05.

The "tube-marlin.gcode" file is different from the one you posted? Most likely, if the firmware is set to Marlin in PrusaSlicer, the slicer is adding the motor speed/acceleration/jerk codes. The main problem with that is that Marlin specifies these in mm/s, while RRF specifies them in mm/minute, so they are very low values for RRF.

Ian

Jes, I degraded back to 2.05 now, the warnings are gone, but first it didn't home when the warning turned on. That is fixed now!

[stienfromarden]

Ignore the marlin file that one was very slow, I only use reprap flavor now, I thought it would be a solution to switch to marlin..

To be sure, this is the file I am trying now:

tubev03.gcode

[stienfromarden]

ok, I just tried to print from Simplify3D and that worked... so i'm going to compare the gcode files now

[droftarts]

@Veti Sorry, meant to add "but the Duet firmware should be limiting this", though it's where the problem seems to be.

@stienfromarden Are you resetting after each attempt to run gcode? Or at least re-run config.g (send M98 P"config.g"). This resets any motor settings before attempting to run again. Can you post your homing gcode files, too? While the probing command works okay, which is after, I'm wondering if something in there is causing problems.

Two things from config.g and gcode file:

M563 P0 S"SuperVolcano"'' D0 H1 ; Define tool
There's two apostraphes '' after the end quote of SuperVolcano. These are probably ignored, but remove them anyway.

I don't see any tool command to select the tool, eg T0, either in config.g or the gcode. You do this manually? Probably not an issue, as you said that it did the retraction.

Ian

[stienfromarden]

Yes I need to do a reset because canceling the print is not working, because the xy axis don't move back to 0.

If I compare the two gcode files from PrusaSlic3r and Simplify3D there are differences in speed of the Z axis:

Prusa: F18000
S3D: F1002

But I just don't know where to change this in PrusaSlic3r. Travel speed should be 300mm/s (f18000) because of the large volume..

[stienfromarden]

ok, with travel speed set to 10mm/s in prusaslic3r it works.. but slow, very slow... and then it stops after 20cm

I also did the M201 / M205 command, resulting in this: