• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Duet 2 Wifi on a Wanhao Duplicator 6?

Scheduled Pinned Locked Moved
Duet Hardware and wiring
8
34
2.3k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    droftarts administrators @PXP11
    last edited by 9 Jan 2020, 15:05

    @PXP11 If having an LCD display is important, get a Maestro (only 12864 LCDs are supported) and use an ethernet wifi router/dongle as a bridge between the Maestro and Wifi. If you can live without the LCD, get a Duet Wifi and any old/cheap wifi-capable phone/tablet, mount the phone/tablet on the printer, and run the Duet Web Control on that.

    There is also PrintEye, that should run on any Duet, but requires some extra hardware. https://forum.duet3d.com/topic/12197/printeye-simple-information-panel-for-duet-boards

    Ian

    Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

    1 Reply Last reply Reply Quote 0
    • undefined
      PXP11
      last edited by 9 Jan 2020, 16:00

      I think, after reading all your helpful advice, I have made a decision. Duet 2 wifi it is and I'll take the old phone as a new screen. This way I know it will work 🙂 .
      Is there a non sketchy way to use the 5V from the board to permanently power the phone or is this a bad idea?

      1 Reply Last reply Reply Quote 0
      • undefined
        jay_s_uk
        last edited by 9 Jan 2020, 16:04

        You'd be better of with a separate power supply.

        Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

        1 Reply Last reply Reply Quote 0
        • undefined
          DIY-O-Sphere
          last edited by DIY-O-Sphere 1 Sept 2020, 16:05 9 Jan 2020, 16:04

          You should separate that.

          (UTC+1)

          1 Reply Last reply Reply Quote 0
          • undefined
            PXP11
            last edited by 9 Jan 2020, 16:33

            Thought so...
            Anyway thanks a lot for the helpful advice and I'll be back, most likely when I start the wiring 😉

            1 Reply Last reply Reply Quote 0
            • undefined
              PXP11
              last edited by 9 Jan 2020, 19:01

              Well there is one last question I guess: I'd realy like to keep the ribbon cable (just looks so clean 😄 ). It's a 2x8 pin DIN 41651 connector. Can I just use it to go up to the board and then split the cable off into the corresponding connection points for extruder stepper, thermistor, heater and fans?
              There will of course be a seperating connector in between.!

              Ugly sketch to show my intent:
              The 2x and 4x are representing the number of wires.

              IMG_20200109_195534.jpg

              The connector if someone wonders what DIN DIN 41651 2x8 looks like:
              IMG_20200109_185650.jpg

              ? 1 Reply Last reply 9 Jan 2020, 19:31 Reply Quote 0
              • ?
                A Former User @PXP11
                last edited by A Former User 1 Sept 2020, 19:32 9 Jan 2020, 19:31

                @PXP11 said in Duet 2 Wifi on a Wanhao Duplicator 6?:

                Can I just use it to go up to the board and then split the cable off into the corresponding connection points for extruder stepper, thermistor, heater and fans?

                https://www.thingiverse.com/thing:3465278

                maybe can inspire? could add a 16p one if it helps..

                undefined 1 Reply Last reply 9 Jan 2020, 19:47 Reply Quote 0
                • undefined
                  PXP11 @A Former User
                  last edited by 9 Jan 2020, 19:47

                  @bearer
                  Well yes that's more or less the idea I had in mind. Just there will be 3x 2-pin, 1x 4-pin and the two heater leads on the ends instead of the male connection pins.

                  1 Reply Last reply Reply Quote 0
                  • ?
                    A Former User
                    last edited by 9 Jan 2020, 19:51

                    Sure, can turn it into whatever you need, i just used it to collect a couple of 1x2 and 1x4 dupont wires into a shrouded 2x8, the other ends were fitted with molex that fit the duet

                    undefined 1 Reply Last reply 9 Jan 2020, 19:55 Reply Quote 0
                    • undefined
                      PXP11 @A Former User
                      last edited by 9 Jan 2020, 19:55

                      @bearer
                      So basically you did the same thing as I have in mind and it works?

                      1 Reply Last reply Reply Quote 0
                      • ?
                        A Former User
                        last edited by 9 Jan 2020, 20:00

                        I fitted a Maestro in an Tiertime Up Mini 2, making adapters for all the originals cables and plugs. But yeah works, although I did change the heater screw terminal on the Duet to a pluggable one.
                        c643612f-78e4-4aa9-a80f-849e87fd5778-image.png

                        undefined 1 Reply Last reply 9 Jan 2020, 20:09 Reply Quote 0
                        • undefined
                          PXP11 @A Former User
                          last edited by 9 Jan 2020, 20:09

                          @bearer
                          Perfect! Thank you very much!👍

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            jith
                            last edited by jith 14 Sept 2022, 04:41

                            @PXP11 Did you lose z height when you installed the mosquito on your D6?

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              PXP11
                              last edited by 14 Sept 2022, 06:11

                              @jith No I did not. But mounting the mosquito to the D6 involved milling off part of the original printhead and drilling some accurate holes. So you would need access to a machine shop or milling machine of sorts. And you will cross a point of no return because there are not a lot of spare D6 printheads flying around (tapping M2.5 threads gets really interesting) 😋. If you are interested I can send you all the CAD files so you can have a look.

                              undefined 1 Reply Last reply 18 Sept 2022, 17:41 Reply Quote 0
                              • undefined
                                jith @PXP11
                                last edited by jith 18 Sept 2022, 17:41

                                @pxp11 That would be great, thanks. I don't have access to a milling machine so I think I'll be printing a replacement carriage out of petg or resin.

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA