Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    duet 3 endstop wiring

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    33
    3.1k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Dad003undefined
      Dad003 @Danal
      last edited by

      @Danal

      when i try this G code it tell me the pin is not free and nothing happen

      1 Reply Last reply Reply Quote 0
      • Danalundefined
        Danal
        last edited by

        Then you have something else in your config.g that defines that pin, before what you are trying. There are no default assignments.

        Did you remove the M950?

        Delta / Kossel printer fanatic

        1 Reply Last reply Reply Quote 0
        • Dad003undefined
          Dad003
          last edited by

          this is what i have for config file

          ; Drives
          M569 P0.0 S1 ; physical drive 0.0 goes forwards
          M569 P0.1 S1 ; physical drive 0.1 goes forwards
          M569 P0.2 S1 ; physical drive 0.2 goes forwards
          M569 P0.5 S1 ; physical drive 0.5 goes forwards
          M569 P0.4 S0 ; physical drive 0.4 goes forwards
          M584 X0.0 Y0.1 Z0.2 E0.5:0.4 ; set drive mapping
          M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
          M92 X160.00 Y160.00 Z6400.00 E172.64:172.64 ; set steps per mm
          M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
          M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
          M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
          M906 X800 Y800 Z800 E800:800 I50 ; set motor currents (mA) and motor idle factor in per cent
          M84 S30 ; Set idle timeout

          ; Axis Limits
          M208 X0 Y0 Z0 S1 ; set axis minima
          M208 X360 Y260 Z700 S0 ; set axis maxima

          ; Endstops
          M574 X1 S1 P"io0.in" ; configure active-low endstop for low end on X via pin io0.in
          M574 Y2 S1 P"io2.in" ; configure active-low endstop for high end on Y via pin io2.in
          M574 Z2 S1 P"io1.in" ; configure active-low endstop for low end on Z via pin io1.in

          ; Z-Probe
          M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
          M557 X15:215 Y15:195 S20 ; define mesh grid

          ; Heaters
          M308 S0 P"temp3" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp3
          M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
          M143 H0 S120 ; set temperature limit for heater 0 to 120C
          M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
          M140 H0 ; map heated bed to heater 0
          M308 S1 P"spi.cs0" Y"thermocouple-max31856" ; configure sensor 1 as thermocouple via CS pin spi.cs0
          M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
          M143 H1 S260 ; set temperature limit for heater 1 to 260C
          M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
          M308 S2 P"spi.cs1" Y"thermocouple-max31856" ; configure sensor 2 as thermocouple via CS pin spi.cs1
          M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
          M143 H2 S290 ; set temperature limit for heater 2 to 290C
          M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

          ; Fans
          M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
          M106 P0 C"extruder 1" S1 H1 T45 ; set fan 0 name and value. Thermostatic control is turned on
          M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
          M106 P1 C"extruder 2" S1 H2 T45 ; set fan 1 name and value. Thermostatic control is turned on
          M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
          M106 P2 C"blower" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off
          M950 F3 C"out6" Q500 ; create fan 3 on pin out6 and set its frequency
          M106 P3 C"electrical" S1 H1:2 T30 ; set fan 3 name and value. Thermostatic control is turned on

          ; Tools
          M563 P1 D0 H1 F0 ; define tool 1
          G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
          G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
          M563 P2 D1 H2 F0 ; define tool 2
          G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
          G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

          ; Custom settings are not defined

          ; Miscellaneous
          M501 ; load saved parameters from non-volatile memory
          M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
          T1 ; select first tool

          A Former User? 1 Reply Last reply Reply Quote 0
          • A Former User?
            A Former User @Dad003
            last edited by

            @Dad003 said in duet 3 endstop wiring:

            M574 X1 S1 P"io0.in" ; configure active-low endstop for low end on X via pin io0.in
            M574 Y2 S1 P"io2.in" ; configure active-low endstop for high end on Y via pin io2.in
            M574 Z2 S1 P"io1.in" ; configure active-low endstop for low end on Z via pin io1.in

            try
            M574 X1 S1 P"!io0.in"

            and so on

            Dad003undefined 1 Reply Last reply Reply Quote 0
            • Dad003undefined
              Dad003
              last edited by

              my endstop are assigne to io_0 , io_1 and io_2

              1 Reply Last reply Reply Quote 0
              • A Former User?
                A Former User
                last edited by

                note the exclamation point before the pin name, should invert the pin so its active when pressed instead of the other way around.

                1 Reply Last reply Reply Quote 0
                • Dad003undefined
                  Dad003 @A Former User
                  last edited by

                  @bearer said in duet 3 endstop wiring:

                  M574 X1 S1 P"!io0.in"

                  thank you , that solved my problem !

                  and another problem gone , now i need to figure out why the bed heat so slow

                  1 Reply Last reply Reply Quote 0
                  • Dad003undefined
                    Dad003
                    last edited by

                    so here another development after finally having the limit switch in the right state , trying to home the axis , X will move and do what need to be done , Y will move but not hit the switch or ram into the switch without stopping and say it home and the Z axis will move like 10mm and nothing else without even ever getting close of the switch

                    him using the basic g code from the RRF Config tool, i even copy pasted the X home code that was working and switching the coordinate and axis and it still doesnt work

                    ; homeall.g
                    ; called to home all axes
                    ;
                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                    G91 ; relative positioning
                    G1 H2 Z-5 F3000 ; lift Z relative to current position
                    G1 H1 X-365 Y255 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
                    G1 H2 X5 Y-5 F3000 ; go back a few mm
                    G1 H1 X-365 Y255 F360 ; move slowly to X and Y axis endstops once more (second pass)
                    G1 H1 Z-805 F360 ; move Z down stopping at the endstop
                    G90 ; absolute positioning
                    G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                    ; Uncomment the following lines to lift Z after probing
                    ;G91 ; relative positioning
                    ;G1 Z-5 F50 ; lift Z relative to current position
                    ;G90 ; absolute positioning

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by

                      Please reset the homing files to the ones the the configurator generated, and post them here along with your current config.g file.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      Dad003undefined 1 Reply Last reply Reply Quote 0
                      • Dad003undefined
                        Dad003
                        last edited by Dad003

                        @dc42 ok,

                        here the Z home

                        **; homez.g
                        ; called to home the Z axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                        G91 ; relative positioning
                        G1 H2 Z-5 F3000 ; lift Z relative to current position
                        G1 H1 Z-805 F1800 ; move Z down until the endstop is triggered
                        G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                        ; Uncomment the following lines to lift Z after probing
                        ;G91 ; relative positioning
                        ;G1 Z-5 F50 ; lift Z relative to current position
                        ;G90 ; absolute positioning**

                        here the Y home

                        ; homey.g
                        ; called to home the Y axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                        G91 ; relative positioning
                        G1 H2 Z-5 F3000 ; lift Z relative to current position
                        G1 H1 Y255 F1800 ; move quickly to Y axis endstop and stop there (first pass)
                        G1 H2 Y-5 F3000 ; go back a few mm
                        G1 H1 Y255 F360 ; move slowly to Y axis endstop once more (second pass)
                        G1 H2 Z5 F3000 ; lower Z again
                        G90 ; absolute positioning

                        the X files

                        ; homex.g
                        ; called to home the X axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                        G91 ; relative positioning
                        G1 H2 Z-5 F3000 ; lift Z relative to current position
                        G1 H1 X-365 F1800 ; move quickly to X axis endstop and stop there (first pass)
                        G1 H2 X5 F3000 ; go back a few mm
                        G1 H1 X-365 F360 ; move slowly to X axis endstop once more (second pass)
                        G1 H2 Z5 F3000 ; lower Z again
                        G90 ; absolute positioning

                        ANd my config file

                        **; Configuration file for Duet 3 (firmware version 3)
                        ; executed by the firmware on start-up
                        ;
                        ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)

                        ; General preferences
                        G90 ; send absolute coordinates...
                        M83 ; ...but relative extruder moves
                        M550 P"The mean printer" ; set printer name

                        ; Network
                        M551 P"9410648" ; set password
                        M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
                        M586 P0 S1 ; enable HTTP
                        M586 P1 S1 ; enable FTP
                        M586 P2 S0 ; disable Telnet

                        ; Drives
                        M569 P0.0 S1 ; physical drive 0.0 goes forwards
                        M569 P0.1 S1 ; physical drive 0.1 goes forwards
                        M569 P0.2 S1 ; physical drive 0.2 goes forwards
                        M569 P0.5 S0 ; physical drive 0.5 goes backwards
                        M569 P0.4 S1 ; physical drive 0.4 goes forwards
                        M584 X0.0 Y0.1 Z0.2 E0.5:0.4 ; set drive mapping
                        M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
                        M92 X160.00 Y160.00 Z3200.00 E172.64:172.60 ; set steps per mm
                        M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                        M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
                        M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
                        M906 X1500 Y1500 Z1200 E1500:1500 I30 ; set motor currents (mA) and motor idle factor in per cent
                        M84 S30 ; Set idle timeout

                        ; Axis Limits
                        M208 X0 Y0 Z0 S1 ; set axis minima
                        M208 X360 Y250 Z800 S0 ; set axis maxima

                        ; Endstops
                        M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin io0.in
                        M574 Y2 S1 P"!io2.in" ; configure active-high endstop for high end on Y via pin io2.in
                        M574 Z2 S1 P"!io1.in" ; configure active-high endstop for low end on Z via pin io1.in

                        ; Z-Probe
                        M558 P0 H-5 F120 T3000 ; disable Z probe but set dive height, probe speed and travel speed
                        M557 X15:215 Y15:195 S20 ; define mesh grid

                        ; Heaters
                        M308 S0 P"temp3" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin temp3
                        M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                        M143 H0 S120 ; set temperature limit for heater 0 to 120C
                        M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                        M140 H0 ; map heated bed to heater 0
                        M308 S1 P"spi.cs0" Y"thermocouple-max31856" ; configure sensor 1 as thermocouple via CS pin spi.cs0
                        M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                        M143 H1 S260 ; set temperature limit for heater 1 to 260C
                        M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                        M308 S2 P"spi.cs1" Y"thermocouple-max31856" ; configure sensor 2 as thermocouple via CS pin spi.cs1
                        M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
                        M143 H2 S290 ; set temperature limit for heater 2 to 290C
                        M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                        ; Fans
                        M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
                        M106 P0 C"extruder 1" S1 H1 T45 ; set fan 0 name and value. Thermostatic control is turned on
                        M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
                        M106 P1 C"extruder 2" S1 H2 T45 ; set fan 1 name and value. Thermostatic control is turned on
                        M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
                        M106 P2 C"blower" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off
                        M950 F3 C"out6" Q500 ; create fan 3 on pin out6 and set its frequency
                        M106 P3 C"electrical" S1 H1:2 T30 ; set fan 3 name and value. Thermostatic control is turned on

                        ; Tools
                        M563 P1 D0 H1 F0 ; define tool 1
                        G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                        G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
                        M563 P2 D1 H2 F0 ; define tool 2
                        G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
                        G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

                        ; Custom settings are not defined

                        ; Miscellaneous
                        M501 ; load saved parameters from non-volatile memory
                        T1 ; select first tool**

                        MY bed should go down hit the limit switch and back up but nothing happen when i try to home that one but it will move when using control

                        Phaedruxundefined 1 Reply Last reply Reply Quote 0
                        • Dad003undefined
                          Dad003
                          last edited by Dad003

                          Here something weird , i was trying to tune the heat bed and started homing Y actually worked like intended i didn't change anything in the config when it wasnt working 15 min earlier

                          1 Reply Last reply Reply Quote 0
                          • Dad003undefined
                            Dad003 @dc42
                            last edited by

                            @dc42

                            So i tested something here , tried ot home the Z with heat bed OFF it move 10mm and stop , started heated bed and boom Z axis keep moving , ANy idea what G CODE i should had or remove or modify ?

                            1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator
                              last edited by

                              You're set up to home to Z max. Where is the endstop located? Is it at the bottom when the be is closest to the nozzle or is it at the opposite end?

                              Z-Bot CoreXY Build | Thingiverse Profile

                              Dad003undefined 1 Reply Last reply Reply Quote 0
                              • Dad003undefined
                                Dad003 @Phaedrux
                                last edited by

                                @Phaedrux ends stop is at the bottom the opposite side of the hot end ,

                                1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator @Dad003
                                  last edited by

                                  @Dad003 said in duet 3 endstop wiring:

                                  ; homez.g
                                  ; called to home the Z axis
                                  ;
                                  ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                                  G91 ; relative positioning
                                  G1 H2 Z-5 F3000 ; lift Z relative to current position
                                  G1 H1 Z-805 F1800 ; move Z down until the endstop is triggered
                                  G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
                                  ; Uncomment the following lines to lift Z after probing
                                  ;G91 ; relative positioning
                                  ;G1 Z-5 F50 ; lift Z relative to current position
                                  ;G90 ; absolute positioning

                                  Ok, in that case your homez should have a positive Z movement to the endstop rather than negative.

                                  G1 H1 Z805 F1800

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  1 Reply Last reply Reply Quote 0
                                  • Dad003undefined
                                    Dad003
                                    last edited by Dad003

                                    So after a few frustrating days i still have problem , my Y axis and Z axis will not home , they move a little and the duet web control show as home when they didnt even touch the limit switch

                                    here a video of the Y axis showing my problem , if i run a macro to move the axis after they home everything move fine but homing Y and Z unless they are already next to the limit switch doesnt work they start moving than stop sometime they move more like the video show . Either it a parameter that i dont see somewhere in the config but it not the gcode in the home files since the X work fine , if it neither in the file than is a firmware issue and it a big one , him running the last available firmware 3.01 RC11.

                                    https://www.youtube.com/watch?v=VYiLlLr1R1s

                                    ; homey.g
                                    ; called to home the Y axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z5 F3000 ; lower Z relative to current position
                                    G1 H2 Y-5 F3000
                                    G1 H1 Y300 F3000 ; move quickly to Y axis endstop and stop there (first pass)
                                    G1 H2 Y-5 F3000 ; go back a few mm
                                    G1 H1 Y300 F360 ; move slowly to Y axis endstop once more (second pass)
                                    G90 ; absolute positioning

                                    ; homez.g
                                    ; called to home the Z axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z10 F3000 ; lift Z relative to current position
                                    G1 H1 Z805 F3000 ; move Z down until the endstop is triggered
                                    G92 Z572 ; set Z position to axis minimum (you may want to adjust this)

                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91 ; relative positioning
                                    ;G1 Z-5 F50 ; lift Z relative to current position
                                    ;G90 ; absolute positioning

                                    ; Configuration file for Duet 3 (firmware version 3)
                                    ; executed by the firmware on start-up
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 03 2020 01:01:37 GMT-0600 (Mountain Daylight Time)

                                    ; General preferences
                                    G90 ; send absolute coordinates...
                                    M83 ; ...but relative extruder moves
                                    M550 P"The mean printer" ; set printer name

                                    ; Network
                                    M551 P"9410648" ; set password
                                    M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
                                    M586 P0 S1 ; enable HTTP
                                    M586 P1 S1 ; enable FTP
                                    M586 P2 S0 ; disable Telnet

                                    ; Drives
                                    M569 P0.0 S1 ; physical drive 0.0 goes forwards
                                    M569 P0.1 S1 ; physical drive 0.1 goes forwards
                                    M569 P0.2 S1 ; physical drive 0.2 goes forwards
                                    M569 P0.5 S0 ; physical drive 0.5 goes backwards
                                    M569 P0.4 S1 ; physical drive 0.4 goes forwards
                                    M584 X0.0 Y0.1 Z0.2 E0.5:0.4 ; set drive mapping
                                    M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
                                    M92 X160.00 Y160.00 Z3200.00 E172.64:172.60 ; set steps per mm
                                    M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                                    M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
                                    M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
                                    M906 X1600 Y1600 Z1200 E1600:1600 I30 ; set motor currents (mA) and motor idle factor in per cent
                                    M84 S30 ; Set idle timeout

                                    ; Axis Limits
                                    M208 X0 Y0 Z0 S1 ; set axis minima
                                    M208 X360 Y250 Z572 S0 ; set axis maxima

                                    ; Endstops
                                    M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin io0.in
                                    M574 Y2 S1 P"!io2.in" ; configure active-high endstop for high end on Y via pin io2.in
                                    M574 Z2 S1 P"!io1.in" ; configure active-high endstop for low end on Z via pin io1.in

                                    ; Z-Probe
                                    M558 P0 H-5 F120 T3000 ; disable Z probe but set dive height, probe speed and travel speed
                                    M557 X15:215 Y15:195 S20 ; define mesh grid

                                    ; Heaters
                                    M308 S0 P"temp3" Y"thermistor" T100000 B4725 ; configure sensor 0 as thermistor on pin temp3
                                    M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                                    M143 H0 S120 ; set temperature limit for heater 0 to 120C
                                    M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                                    M140 H0 ; map heated bed to heater 0
                                    M308 S1 P"spi.cs0" Y"thermocouple-max31856" ; configure sensor 1 as thermocouple via CS pin spi.cs0
                                    M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                                    M143 H1 S260 ; set temperature limit for heater 1 to 260C
                                    M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                                    M308 S2 P"spi.cs1" Y"thermocouple-max31856" ; configure sensor 2 as thermocouple via CS pin spi.cs1
                                    M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
                                    M143 H2 S290 ; set temperature limit for heater 2 to 290C
                                    M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                                    ; Fans
                                    M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
                                    M106 P0 C"extruder 1" S1 H1 T45 ; set fan 0 name and value. Thermostatic control is turned on
                                    M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
                                    M106 P1 C"extruder 2" S1 H2 T45 ; set fan 1 name and value. Thermostatic control is turned on
                                    M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
                                    M106 P2 C"blower" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off
                                    M950 F3 C"out6" Q500 ; create fan 3 on pin out6 and set its frequency
                                    M106 P3 C"electrical" S1 H1:2 T30 ; set fan 3 name and value. Thermostatic control is turned on

                                    ; Tools
                                    M563 P1 D0 H1 F0 ; define tool 1
                                    G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                                    G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
                                    M563 P2 D1 H2 F0 ; define tool 2
                                    G10 P2 X0 Y34.05 Z0 ; set tool 2 axis offsets
                                    G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

                                    ; Custom settings are not defined

                                    ; Miscellaneous
                                    M501 ; load saved parameters from non-volatile memory
                                    T1 ; select first tool

                                    1 Reply Last reply Reply Quote 0
                                    • Danalundefined
                                      Danal
                                      last edited by

                                      @Dad003 said in duet 3 endstop wiring:

                                      M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin io0.in

                                      If you have physical normally closed switches, you do not need the !

                                      Go to the "machine specific" tab and look lower right. There is a sub-screen that shows endstop status. Verify the say "No" under triggered. Then press them with your finger and be sure each says "yes" .

                                      Delta / Kossel printer fanatic

                                      1 Reply Last reply Reply Quote 0
                                      • Dad003undefined
                                        Dad003
                                        last edited by

                                        they are all on no and they all work , when i press them

                                        1 Reply Last reply Reply Quote 0
                                        • Danalundefined
                                          Danal
                                          last edited by

                                          @Dad003 said in duet 3 endstop wiring:

                                          they are all on no and they all work , when i press them

                                          Then the switches themselves are working and configured correctly.

                                          Therefore, look at the homing files, or axis configuration, or other similar things.

                                          Delta / Kossel printer fanatic

                                          1 Reply Last reply Reply Quote 0
                                          • Dad003undefined
                                            Dad003
                                            last edited by

                                            everything move like it should be excepted the homing of Y and Z axis and g code is directly from the tools and check it and check so many time tryed to change value trying to find the problem and nothing , nothing work the homing of the Y or Z never seem to move the same distance every time i call them

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA