extruder doesnt have any torque ( Cant move anything)

[joehsmash]

@Phaedrux i will run through these in a couple hours, tbh i used the reprap config tool and that's what she spit out.

The only things i added/changed were directly related to the problems ive been having.

Ie z motors individually controlled etc.

Thanks for your input

[joehsmash]

@jay_s_uk also thanks for your input as well

[joehsmash]

@Phaedrux just out of curiosity i ran the m98 pconfig.g and it came back with this

5/15/2020, 1:30:30 AM: Connected to 192.168.1.44
5/15/2020, 1:35:20 AM: M98 PCONFIG.G: HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: GCodes: Attempt to read a GCode unsigned array that is too long: M350 X16 Y16 Z16 E16:16 I1
Error: GCodes: Attempt to read a GCode float array that is too long: M92 X80.00 Y80.00 Z800.00 E723.38:800.00
Error: GCodes: Attempt to read a GCode float array that is too long: M566 X1020.00 Y1020.00 Z24.00 E300.00:24.00
Error: GCodes: Attempt to read a GCode float array that is too long: M203 X6000.00 Y6000.00 Z180.00 E1200.00:180.00
Error: GCodes: Attempt to read a GCode float array that is too long: M201 X9000.00 Y9000.00 Z100.00 E10000.00:100.00
Error: GCodes: Attempt to read a GCode float array that is too long: M906 X935 Y935 Z935 E1100:935 I30

[deckingman]

@joehsmash I think it should be M98 P"config.g" (in inverted commas). I don't think it matters with earlier firmware but in later versions it's mandatory (not sure when in changed).

[joehsmash]

after changes, m98 provides me with this

5/15/2020, 1:40:21 AM:
M98 PCONFIG.G: HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

[joehsmash]

@deckingman tried to run as you suggested

5/15/2020, 1:42:30 AM: M98 P CONFIG.G: Warning: Macro file CONFIG.G not found.
5/15/2020, 1:42:52 AM: M98 P "config.g": Warning: Macro file "config.g" not found.

[joehsmash]

@Phaedrux that was it!

swapped it all out like you suggested and BAM.

stepper is so strong it wants to rip my finger off!

[deckingman]

@joehsmash said in extruder doesnt have any torque ( Cant move anything):

@deckingman tried to run as you suggested

5/15/2020, 1:42:30 AM: M98 P CONFIG.G: Warning: Macro file CONFIG.G not found.
5/15/2020, 1:42:52 AM: M98 P "config.g": Warning: Macro file "config.g" not found.

I guess your problem is now sorted so it doesn't really matter, but that's odd. Maybe I read something wrong here https://duet3d.dozuki.com/Wiki/Gcode#Section_M98_Call_Macro_Subprogram

[Dougal1957]

@deckingman spaces after the P would maybe cause that error!

[Phaedrux]

@deckingman said in extruder doesnt have any torque ( Cant move anything):

Maybe I read something wrong here

I think the difference is that he's still on RRF2.

@Dougal1957 said in extruder doesnt have any torque ( Cant move anything):

spaces after the P would maybe cause that error!

That could be.

@joehsmash said in extruder doesnt have any torque ( Cant move anything):

tepper is so strong it wants to rip my finger off!

Glad that worked.