Homing advice

Phaedrux

Change the Gcode flavor to RepRap.

Can you share an actual sliced gcode file?

agent0810

yea let me see what i can get. should i just place G90 in before the G92? googled it and didnt see an actual setting for it in cura but someone said they just put it in the start code.

Phaedrux

Well I'd like to see the full sliced gcode first to see what it's actually got inserted where.

agent0810

I think this is what you are looking for.

base_x.gcode

Phaedrux

Ok, try changing your start gcode to be

M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

G28 ;Home
G90 ; absolute positioning.

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

G92 E0
G92 E0
G1 F5100 E-7

The other question I have is about your Z probe. Currently you are homing to the Z max position with an endstop. Do you also have a probe installed? Is your Z axis moving correctly?

agent0810

alright ill drop that in there, thank you.

i have this probe that came yesterday i need to install, but i need to print a bracket to put it on before i can lol.

https://www.filastruder.com/products/mini-differential-ir-height-sensor

agent0810

So i think we have progress, no crashing before hand, but the bed goes half way down and then it starts to print but doesnt extrude any fillament.

Phaedrux

That sounds like the Z steps per mm is incorrect.

Try to measure how much it actually moves when you command it to move 10mm.

I'm not sure off hand what the Ender 5 pro Z steps should be, but if you have lead screw and motor details it can be worked out.

Z_steps_per_mm = (motor_steps_per_rev * driver_microstep) / screw_lead

agent0810

i raised it all the way, marked the back, lowered it 10mm then marked the back, lowered the bed out of the way and measured, looks like it only went about 4.5mm.

Will the motor steps and driver info be online or on the device?

thanks again for all your help on this.

Phaedrux

Doing a Google it looks like it might be 800. Which kinda matches with what you've measured.

agent0810

so update that in the config.g?

current:
M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm

change to:
M92 X80.00 Y80.00 Z800.00 E93.00 ; set steps per mm

agent0810

tried that and took a step back.

it crashed a bit when the job started, then the bed lowered probably 3/4 of the way down and its printing now while the bed is still almost all the way down and no fillament coming out of the extruder.

Phaedrux

Does the Z axis move the right amount with 800 steps per mm?

Can you post a video of it running?

Is the extruder motor trying to move at all? Is the hotend at temp?

And just to confirm, after homing you're able to jog the head around the bed fine?

agent0810

This post is deleted!

agent0810

This post is deleted!

agent0810

@Phaedrux

Z axis moves about 11mm when i push 10 now.

working on a video as we speak.

hotend is at temp, i can push fillament through.

i am able to jog the head around the bed fine.

agent0810

@Phaedrux

here is the beggining of it, i could only get that cuz i couldnt get a full size video to upload anywhere. in the video he hear the begining and then the bed start to lower, goes almost all the way down then the extruder starts to move around list its printing with the bed all the way down almost.

https://imgur.com/a/qp8zDKc

Phaedrux

Your Z endstop is at Zmin, not zmax.

Change this M574 Z2 S1 P"zstop" To this M574 Z1 S1 P"zstop"

Then change your homeall and homez from this

G1 H1 Z305 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z300 ; set Z position to axis maximum (you may want to adjust this)

To this

G1 H1 Z-320 F360 ; move Z  stopping at the endstop
G90 ; absolute positioning

Direction change and removing the G92

Phaedrux

It also doesn't look like your hotend fan is spinning. Was it at temp?

agent0810

@Phaedrux

I made all 3 changes, but then when i tried to home it sent the bed to the bottom (homeing was working) so i put it back and put the homing configs back.

left the z endstop the same and the same thing happened when i sent a print job, the bed went to the bottom and then the extruder started trying to print while the bed was at the bottom.

the hotend said it was at temp according to the web page for the board. i was able to mannually turn the fan on with a setting at the bottom of the page.

i feel like we are getting close, sorry for being a pain.