RRF Config Mapping

JoergS5

@printthatthing the
G1 H1 Z-355 F360
should be a replacement for what I proposed (the G30 proposal), but 355 is less than the 500 height of M208, so 0 may not be reached, I would set it higher to Z-600.
And the G92 Z0 is not needed, because the G1 H1 Z... already sets Z to the M208 minimum for Z, ie 0.
The sensitivity setting G31 P is probably wrong, please set P25 instead.

Phaedrux

; Z-Probe
M950 S0 C"duex.pwm5"                          ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X66 Y33 Z2.5                          ; set Z probe trigger value, offset and trigger height

Remove the ! from duex.pwm5
Change G31 P500 to P25

in homeall change

G1 H1 Z-355 F360        ; move Z down stopping at the endstop
G90                     ; absolute positioning
G92 Z0                  ; set Z position to axis minimum (you may want to adjust this)

To

G90                     ; absolute positioning
G1 X150 Y150 F6000        ; move Z down stopping at the endstop
G30 ; probe the bed

printthatthing

Thank you all again. I think I have it running now.
I had to keep ! for duex.pwm5 else it does not probe.
config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Wed Jul 08 2020 21:18:31 GMT+0200 (centraleuropeisk sommartid)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Formbot Raptor 2"                       ; set printer name

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z640.00 E415.00              ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X400 Y400 Z350 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"!xstop"                           ; configure active-high endstop for low end on X via pin !xstop
M574 Y1 S1 P"!ystop"                           ; configure active-high endstop for low end on Y via pin !ystop
M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z


; Z-Probe
M950 S0 C"!duex.pwm5"                           ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-25 Y-5 Z0.489                          ; set Z probe trigger value, offset and trigger height
M557 X5:380 Y5:380 S20                       ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

homeall.g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Wed Jul 08 2020 20:58:26 GMT+0200 (centraleuropeisk sommartid)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-405 Y-405 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-405 Y-405 F360  ; move slowly to X and Y axis endstops once more (second pass)


G90                     ; absolute positioning
G1 X150 Y150 F6000        ; move Z down stopping at the endstop
G30                     ; home Z by probing the bed


; Uncomment the following lines to lift Z after probing
G91                    ; relative positioning
G1 Z5 F100             ; lift Z relative to current position
G90                    ; absolute positioning

Is the heatmap very bad or ok to use without adjustments?

dc42

As you have no DueX, you are not connecting the servo pin of the BLTouch duex.pwm5, so you should not use that selection in configtool or config.g. Use the name of the actual pin that you have connected it to, which is exp.heater7, and don't invert it. Although as it happens, using duex.pwm5 and inverting it will work.

printthatthing

@dc42 Aha, okay that make sense.

Phaedrux

@dc42 said in RRF Config Mapping:

so you should not use that selection in configtool

Unfortunately the config tool currently doesn't show the expansion pins right now, just duex pins.

Phaedrux

@printthatthing said in RRF Config Mapping:

Is the heatmap very bad or ok to use without adjustments?

That's a bit of a saddle shape for sure. You may or may not be able to fix that physically. You can test the effect of the compensation by printing a bed test like this: bedlevel_nozzle_0.4_200x200-0.3-0.8.stl

printthatthing

@Phaedrux Ok thanks.

printthatthing

Now I'm stuck with error at bed heating.
Error: Heater 0 fault: temperature rising much more slowly than the expected 1.7°C/sec
Duet 2 Wifi power a solid state relay for a 220v heater.

I executed M307 H0 S90
M307 H0 results in below.
Heater 0 model: gain 340.0, time constant 140.0, dead time 5.5, max PWM 1.00, calibration voltage 0.0, mode bang-bang

Then I tried to save the value
M307 H0 A340 C140 D5.5 V0 B0
But it result in
Warning: M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

Phaedrux

That's expected. The warning is letting you know what the max uncontrolled temp could be.

printthatthing

@Phaedrux Ok, but I still not able to heat the bed. It start heating but halt after few seconds. Error: Heater 0 fault: temperature rising much more slowly than the expected 1.7°C/sec

Phaedrux

Are you sure you saved the PID tuning results with M500? Do you also have an M501 at the end of config.g to load the saved results?

printthatthing

@Phaedrux i was missing M501 in config.g
Restarted boad but getting same error when trying to heat bed.
Tried to run M307 H0 S90 again but it fails with Error: M307: bad model parameters

; config-override.g file generated in response to M500 at 2020-07-10 23:02
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 A340.0 C140.0 D5.5 S1.00 V0.0 B1
M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

Phaedrux

In config.g change M307 H0 B1 S1.00 to B0

Then delete your config-override.g and run M307 H0 S90 again after a reboot. Then save with M500.

Phaedrux

Also make sure you're starting from a cold bed state.

printthatthing

@Phaedrux said in RRF Config Mapping:

Executed M307 H0 S90 after the suggested changes.
Error: M307: bad model parameters

Update:
My bad, it might be M303 H0 S90

Phaedrux

@printthatthing said in RRF Config Mapping:

Update:
My bad, it might be M303 H0 S90

Yes of course.

printthatthing

@Phaedrux said in RRF Config Mapping:

@printthatthing said in RRF Config Mapping:

Update:
My bad, it might be M303 H0 S90

Yes of course.

Now it works fine:) Thank you so much for all support.