How to use a LED Strip with Duet 2 WiFI?

Chriss

I have a question here too.

I use that code to configure my LED strip:

M950 F3 C"0.out6" Q500
M106 P3 S0

(And I have two macros to turn in on and off via the web or display than.)

So the "controller" is called "Fan 3" on the Display. Is there a way to rename the object? Like I can rename a tool? (563 S"BlaBla")

Cheers, Chriss

Phaedrux

@Chriss Yes, M106 C"LEDs" would give it the name LEDs.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M106_Fan_On

Chriss

@Phaedrux

Thanks! Workes as expected. I expected that in the "M950" because that is the configuration of the object to me and "M106" the "on/off" only. So I did not looked into the docu of M106.
Anyway: Thank you very much for the fast answer.

Cheers, Chriss

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

In config. g
;LED Strip
M950 P2 C"e1heat"
M307 P2 A-1 C-1 D-1

Then add the following to change power output
M42 P2 Sxxx

Done! When I boot the board the pin is setted "high" and the LED stripe is immediately turned on with the maximum pulse width. How can I set to let the pin low when the board starts?

ericlmccormick

Make sure the M42 code is in the slicer startup code and NOT in config.g

I put M32 in my slicer start code which calls beg.g and M0 in my slicer end code which runs stop.g

Then I have M42 P2 S255 in my bed.g and M42 P2 S0 in stop.g and cancel.g

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

Make sure the M42 code is in the slicer startup code and NOT in config.g

I put M32 in my slicer start code which calls beg.g and M0 in my slicer end code which runs stop.g

Then I have M42 P2 S255 in my bed.g and M42 P2 S0 in stop.g and cancel.g

already done but the stripe turns on when I boot the board even without m42

ericlmccormick

@the_dragonlord can you share your config.g file?

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

@the_dragonlord can you share your config.g file?

here it is:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Mon Oct 26 2020 18:43:35 GMT+0100 (Ora standard dell’Europa centrale)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"DragonCore" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; enable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z1200.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X330 Y330 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z0.474 ; set Z probe trigger value, offset and trigger height
M557 X15:315 Y15:315 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T50 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

; Tools
M563 P0 S"E3DVolcano" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue

M501

uh, I forgot to say that I'm using a PWM fan not an heater.....sorry....

Phaedrux

@the_dragonlord said in How to use a LED Strip with Duet 2 WiFI?:

uh, I forgot to say that I'm using a PWM fan not an heater.....sorry....

Which fan header and where is the gcode defining the pin?

ericlmccormick

@the_dragonlord your problem is you have m106 P2 S1 H-1 and you should have m106 P2 S0 H-1

ericlmccormick

@the_dragonlord but I recommend you use a heater and not a fan

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

@the_dragonlord but I recommend you use a heater and not a fan

i can't use a heater because I have to trigger a mosfet to drive the stripe and overriding a heater pin it gives a level of tension not enough for the mosfet to switch. Ay niw I'm using the Fan 2

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

@the_dragonlord your problem is you have m106 P2 S1 H-1 and you should have m106 P2 S0 H-1

excellent, thanks!

ericlmccormick

@the_dragonlord I'm driving the LEDs directly from the board so that I can control the brightness. But if you are driving a MOSFET, then the fan is a better option I guess.

A Former User

@ericlmccormick said in How to use a LED Strip with Duet 2 WiFI?:

@the_dragonlord I'm driving the LEDs directly from the board so that I can control the brightness. But if you are driving a MOSFET, then the fan is a better option I guess.

yes it is, thanks