Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    DWC Z - Axis Movement off by Factor 10

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    3
    35
    1.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Frederikundefined
      Frederik @BoA
      last edited by

      @BoA my extruder Setup:

      Original Bondtech BMG with a E3d Volcano with 0.4 mm micro swiss nozzle and titan heatbreak. 40W Heater and Thermistor 100K
      0.9° Pancake Stepper

      bedheater: 220V AC1.2 kW Keenovo Silicone Pad 400x400

      BoAundefined 1 Reply Last reply Reply Quote 0
      • Frederikundefined
        Frederik
        last edited by

        @BoA said in DWC Z - Axis Movement off by Factor 10:

        M591 D0

        Response: Extruder 0 has no Filament Sensor

        BoAundefined 1 Reply Last reply Reply Quote 0
        • BoAundefined
          BoA @Frederik
          last edited by

          @Frederik BMG with 0.9 stepper + 16 microsteps should have 830steps/mm

          1 Reply Last reply Reply Quote 0
          • Frederikundefined
            Frederik
            last edited by

            i will try it. on moment

            1 Reply Last reply Reply Quote 0
            • BoAundefined
              BoA @Frederik
              last edited by BoA

              @Frederik Paste Your config.g only and result of

              M98 P"config.g"
              
              1 Reply Last reply Reply Quote 0
              • Frederikundefined
                Frederik
                last edited by

                ; Configuration file for Duet 3 (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v3.1.7 on Wed Nov 18 2020 18:04:17 GMT+0100 (Mitteleuropäische Normalzeit)

                ; General preferences

                G90 ; send absolute coordinates...
                M83 ; ...but relative extruder moves
                M550 P"Duet 3" ; set printer name
                M669 K1 ; switch to CoreXZ mode and multiply motor movements by 3 for the Z axis

                ; Drives
                M569 P0.0 S0 ; physical drive 0.0 goes backwards
                M569 P0.1 S0 ; physical drive 0.1 goes backwards
                M569 P0.2 S0 ; physical drive 0.2 goes backwards
                M569 P0.3 S0
                M569 P0.4 S0
                M569 P0.5 S1 ; physical drive 0.5 goes forwards
                M584 X0.1 Y0.0 Z0.2:0.3:0.4 E0.5 ; set drive mapping
                M671 X425:200:-25 Y240:-25:240 S1 P1.25 ; leadscrews at front left, rear middle and front right with 1mm per screw compensation

                ; Movement Parameters

                M350 X16 Y16 Z16 E16 I1 ; configure microstepping without interpolation
                M92 X160.00 Y160.00 Z400.00 E830.00 ; set steps per mm
                M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X12000.00 Y12000.00 Z1800.00 E1200.00 ; set maximum speeds (mm/min)
                M201 X500.00 Y500.00 Z30.00 E250.00 ; set accelerations (mm/s^2)
                M906 X1800 Y1800 Z800 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X400 Y400 Z385 S0 ; set axis maxima

                ; Endstops
                M574 X2 S1 P"!io1.in" ; configure active-high endstop for high end on X via pin !io1.in
                M574 Y1 S1 P"!io0.in" ; configure active-high endstop for low end on Y via pin !io0.in
                M574 Z2 S2 ; configure Z-probe endstop for low end on Z

                ; Duet Laser Filament Sensor

                M591 D0 P5 P"io3.in" R40:120 E3.0 S1 ; Duet3D laser sensor for extruder drive 0, connected to IO 3,
                tolerance 40 to 120%, 3mm comparison length, enabled

                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                M92 X160.00 Y160.00 Z400.00 E837.02 ; set steps per mm
                M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X12000.00 Y12000.00 Z1800.00 E1200.00 ; set maximum speeds (mm/min)
                M201 X500.00 Y500.00 Z30.00 E250.00 ; set accelerations (mm/s^2)
                M906 X1800 Y1800 Z1000 E1200 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X400 Y400 Z400 S0 ; set axis maxima

                ; Endstops
                M574 X2 S1 P"!io1.in" ; configure active-high endstop for high end on X via pin !io1.in
                M574 Y1 S1 P"!io0.in" ; configure active-high endstop for low end on Y via pin !io0.in
                M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                ; Z-Probe
                M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
                M558 P9 C"^io7.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
                G31 P500 X-26 Y2 Z2.5 ; set Z probe trigger value, offset and trigger height
                M557 X0:400 Y0:400 S20 ; define mesh grid

                ; Heaters
                M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
                M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                M140 H0 ; map heated bed to heater 0
                M143 H0 S200 ; set temperature limit for heater 0 to 200C
                M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
                M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                ; Fans
                M950 F0 C"out8" Q500 ; create fan 0 on pin out8 and set its frequency
                M106 P0 C"Hotend" S1 H1 T45 ; set fan 0 name and value. Thermostatic control is turned on
                M950 F1 C"!out4" Q500 ; create fan 1 on pin !out4 and set its frequency
                M106 P1 C"Bauteildüse" S1 H-1 ; set fan 1 name and value. Thermostatic control is turned off

                ; Tools
                M563 P0 S"E3D V6 0.4 Steel" D0 H1 F0:1 ; define tool 0
                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                ; Custom settings are not defined

                ; Miscellaneous

                M501 ; load saved parameters from non-volatile memory
                M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                T0 ; select first tool

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti
                  last edited by

                  @Frederik said in DWC Z - Axis Movement off by Factor 10:

                  M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                  M92 X160.00 Y160.00 Z400.00 E837.02 ; set steps per mm
                  M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                  M203 X12000.00 Y12000.00 Z1800.00 E1200.00 ; set maximum speeds (mm/min)
                  M201 X500.00 Y500.00 Z30.00 E250.00 ; set accelerations (mm/s^2)
                  M906 X1800 Y1800 Z1000 E1200 I30 ; set motor currents (mA) and motor idle factor in per cent
                  M84 S30 ; Set idle timeout
                  ; Axis Limits
                  M208 X0 Y0 Z0 S1 ; set axis minima
                  M208 X400 Y400 Z400 S0 ; set axis maxima
                  ; Endstops
                  M574 X2 S1 P"!io1.in" ; configure active-high endstop for high end on X via pin !io1.in
                  M574 Y1 S1 P"!io0.in" ; configure active-high endstop for low end on Y via pin !io0.in
                  M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                  this section is still in your config twice

                  1 Reply Last reply Reply Quote 0
                  • Frederikundefined
                    Frederik
                    last edited by

                    config (1).g

                    wow, i dont know why its doubling these lines 😮 ?!?

                    1 Reply Last reply Reply Quote 0
                    • Frederikundefined
                      Frederik
                      last edited by

                      in my normal config. in DWC there is this section only once

                      BoAundefined 1 Reply Last reply Reply Quote 0
                      • BoAundefined
                        BoA @Frederik
                        last edited by

                        @Frederik drag and drop file instead of copy paste content

                        1 Reply Last reply Reply Quote 0
                        • Frederikundefined
                          Frederik
                          last edited by

                          ok.
                          i restartet my DWC and now it looks good i think 🙂

                          1 Reply Last reply Reply Quote 0
                          • Frederikundefined
                            Frederik
                            last edited by

                            config (1).g

                            1 Reply Last reply Reply Quote 0
                            • Frederikundefined
                              Frederik
                              last edited by

                              @Frederik said in DWC Z - Axis Movement off by Factor 10:

                              M591

                              i get always the error M591 no pin name given.

                              do i have to use the m950 command befor to create a pin ?

                              BoAundefined 1 Reply Last reply Reply Quote 0
                              • BoAundefined
                                BoA @Frederik
                                last edited by

                                @Frederik M591 D0 P5 P"io3.in" R40:120 E3.0 S1 should be
                                M591 D0 P5 C"io3.in" R40:120 E3.0 S1

                                Frederikundefined 1 Reply Last reply Reply Quote 1
                                • Frederikundefined
                                  Frederik
                                  last edited by

                                  WOW, Thank You soooo much.

                                  Now my Z Axis working almost spot on...only minor adjustments needed.

                                  Your Tip with the Extruder E steps was perfekt.

                                  now there is only the error message from the filament Sensor ,

                                  and i have to try if the auto bed leveling with the 3 independet z motors will work as expected with my BLTouch.

                                  What Slicer do you use or recommend ?

                                  I tried
                                  Cura 4.8.0 and Prusaslicer .

                                  Simplyfy 3d looks also realy nice, but i cant find a demmo version or similar. Its a hefty Price Tag for a Slicer and when i am reading the reviews on the internet ,i dont know if it is good at the moment with 4.1 or should i wait till the new update is released ?

                                  1 Reply Last reply Reply Quote 1
                                  • Frederikundefined
                                    Frederik @BoA
                                    last edited by

                                    @BoA Thank YOU 😉

                                    M591 D0

                                    Duet3D laser filament monitor v1 on pin io3.in, enabled, allow 40% to 120%, check every 3.0mm, version 1, no calibration data

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA