Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Newbie: New Install on Ender 5 Plus---Willing to PAY$$$

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    6
    141
    7.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • shattyundefined
      shatty @Veti
      last edited by

      This post is deleted!
      1 Reply Last reply Reply Quote 0
      • shattyundefined
        shatty @Veti
        last edited by

        @Veti IMG_2609.HEIC IMG_2610.HEIC IMG_2611.HEIC IMG_2612.HEIC IMG_2613.HEIC IMG_2616.HEIC IMG_2617.HEIC IMG_2618.HEIC

        Vetiundefined 1 Reply Last reply Reply Quote 0
        • Vetiundefined
          Veti @shatty
          last edited by

          @shatty
          i cant view those images. can you post normal jpgs?

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            It looks like it was printed too hot. So dial it back to 200 and see how it goes.

            Z-Bot CoreXY Build | Thingiverse Profile

            shattyundefined 1 Reply Last reply Reply Quote 0
            • shattyundefined
              shatty @Phaedrux
              last edited by shatty

              This post is deleted!
              1 Reply Last reply Reply Quote 0
              • shattyundefined
                shatty
                last edited by

                Not bad for a first print! LOL I was at 220. Where can I set my bed temps and extruder temps during printing? In the filament config.g?

                Phaedruxundefined 1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator @shatty
                  last edited by

                  @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                  Where can I set my bed temps and extruder temps during printing?

                  You set them in the slicer. Then during a print if you want to change them, you can use the web interface to entire a new temperature.

                  Z-Bot CoreXY Build | Thingiverse Profile

                  shattyundefined 1 Reply Last reply Reply Quote 0
                  • shattyundefined
                    shatty @Phaedrux
                    last edited by

                    @Phaedrux TY. During heat up if i were to set in the UI, it would always revert. I had to wait until pre-heat was done

                    1 Reply Last reply Reply Quote 0
                    • shattyundefined
                      shatty
                      last edited by

                      Also, Im using Creality Slicer. What is a good nonbranded software? Like top-notch. And how do I earn 1 reputation? This 60 sec post thing is annoying

                      1 Reply Last reply Reply Quote 1
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        Give PrusaSlicer a try. Probably your best bet. You will have to do a bit of setup. I think it has a profile for the Ender 3 which should get you 99% of the way there.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        shattyundefined 1 Reply Last reply Reply Quote 0
                        • shattyundefined
                          shatty @Phaedrux
                          last edited by

                          @Phaedrux I tried Ultimaker last night but it seemed too complicated

                          1 Reply Last reply Reply Quote 0
                          • Vetiundefined
                            Veti
                            last edited by

                            prusaslicer is easier, it has far less options

                            1 Reply Last reply Reply Quote 1
                            • shattyundefined
                              shatty
                              last edited by

                              IMG_2610.jpg IMG_2609.jpg IMG_2611.jpg IMG_2613.jpg IMG_2612.jpg IMG_2616.jpg IMG_2617.jpg IMG_2618.jpg

                              1 Reply Last reply Reply Quote 0
                              • shattyundefined
                                shatty
                                last edited by

                                What speed to print at? Fast (0.2mm), Normal (0.15mm), or HQ (0.1mm)?

                                Vetiundefined 1 Reply Last reply Reply Quote 0
                                • Vetiundefined
                                  Veti
                                  last edited by

                                  yes print cooler.

                                  also post your config.g

                                  1 Reply Last reply Reply Quote 0
                                  • Vetiundefined
                                    Veti @shatty
                                    last edited by

                                    @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                                    Fast (0.2mm)

                                    i use this for most prints. and about 60mm/s on my ender 3.

                                    1 Reply Last reply Reply Quote 0
                                    • shattyundefined
                                      shatty
                                      last edited by

                                      ; Configuration file for Duet WiFi (firmware version 3)
                                      ; executed by the firmware on start-up
                                      ;
                                      ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)

                                      ; General preferences
                                      G90 ; send absolute coordinates...
                                      M83 ; ...but relative extruder moves
                                      M550 P"E5Plus" ; set printer name

                                      ; Network
                                      M551 P"xxxxx" ; set password
                                      M552 S1 ; enable network
                                      M586 P0 S1 ; enable HTTP
                                      M586 P1 S0 ; disable FTP
                                      M586 P2 S0 ; disable Telnet

                                      ; Drives
                                      M569 P0 S0 ; physical drive 0 goes forwards
                                      M569 P1 S0 ; physical drive 1 goes forwards
                                      M569 P2 S1 ; physical drive 2 goes backwards
                                      M569 P3 S1 ; physical drive 3 goes forwards
                                      M584 X0 Y1 Z2 E3 ; set drive mapping
                                      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                                      M92 X80.00 Y80.00 Z800.00 E130 ; set steps per mm
                                      M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
                                      M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
                                      M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
                                      M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
                                      M84 S30 ; Set idle timeout

                                      ; Axis Limits
                                      M208 X0 Y0 Z0 S1 ; set axis minima
                                      M208 X350 Y350 Z400 S0 ; set axis maxima

                                      ; Endstops
                                      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                                      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                                      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                                      ; Z-Probe
                                      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
                                      M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
                                      G31 P500 X16.3 Y14 Z2.43 ; set Z probe trigger value, offset and trigger height
                                      M557 X15:190 Y15:190 S20 ; define mesh grid

                                      ; Heaters
                                      M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
                                      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                                      M307 H0 A101.7 C607.1 D2.6 S1.00 V24.3 B0 ; enable bang-bang mode for the bed heater and set PWM limit
                                      M140 H0 ; map heated bed to heater 0
                                      M143 H0 S110 ; set temperature limit for heater 0 to 110C
                                      M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
                                      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                                      M307 H1 A268.5 C102.1 D3.1 S1.00 V24.2 B0 ; disable bang-bang mode for heater and set PWM limit
                                      M143 H1 S280 ; 280 deg max on hot end

                                      ; Fans
                                      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                                      M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
                                      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                                      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

                                      ; Tools
                                      M563 P0 D0 H1 F0 ; define tool 0
                                      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                                      ; Custom settings are not defined

                                      ; Miscellaneous
                                      M575 P1 S1 B57600 ; enable support for PanelDue

                                      Vetiundefined 1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti @shatty
                                        last edited by Veti

                                        @shatty

                                        is the thermistor the original thermistor of the ender 5?

                                        if yes change both M308 to T98801 B4185

                                        shattyundefined 1 Reply Last reply Reply Quote 0
                                        • shattyundefined
                                          shatty @Veti
                                          last edited by

                                          @Veti yes.

                                          1 Reply Last reply Reply Quote 0
                                          • shattyundefined
                                            shatty
                                            last edited by

                                            @Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                                            T98801 B4185

                                            Do i have to auto tune again?

                                            Vetiundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA