Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    ToolBoard: 2 wires fan, heater fault and how to extrude ?

    Scheduled Pinned Locked Moved Unsolved
    Duet Hardware and wiring
    6
    112
    5.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Vetiundefined
      Veti @Pseud3mys
      last edited by

      @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

      I power the board with 12v. But if I power with 24v did the output will go up 24v as well ?

      no
      see the wiring diagram.

      https://duet3d.dozuki.com/Wiki/Duet_3_Tool_Board

      the out is 12v

      Pseud3mysundefined 1 Reply Last reply Reply Quote 0
      • Pseud3mysundefined
        Pseud3mys
        last edited by

        ah yes, thank you

        1 Reply Last reply Reply Quote 0
        • Pseud3mysundefined
          Pseud3mys @Veti
          last edited by Pseud3mys

          @Veti have you an idea for the heater fault or the cold extrusion ?

          I send M302 P1 to allow cold extrusion, and I test if the command went good:
          "Cold extrusion is allowed (use M302 P0 to forbid it)"

          but I still can't use it:Capture.PNG

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti
            last edited by

            what is the error message in the console?

            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
            • Pseud3mysundefined
              Pseud3mys @Veti
              last edited by Pseud3mys

              @Veti there are no error message. When I click on the "extrude" button nothing happen

              Vetiundefined 1 Reply Last reply Reply Quote 0
              • Vetiundefined
                Veti @Pseud3mys
                last edited by

                @Pseud3mys
                for the heating. how did you get the error?

                you still have not posted your config.g

                Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                • Pseud3mysundefined
                  Pseud3mys @Veti
                  last edited by

                  @Veti for the heating a fault accure 2 or 3 sec after the start. But the temperature problem is good now.
                  here is my config..g:
                  config.g

                  ; Configuration file for Duet 3 (firmware version 3)
                  ; executed by the firmware on start-up
                  ;
                  ; generated by RepRapFirmware Configuration Tool v3.1.9 on Wed Dec 02 2020 17:31:45 GMT+0100 (heure normale d’Europe centrale)
                  
                  ; General preferences
                  G90                                                          ; send absolute coordinates...
                  M83                                                          ; ...but relative extruder moves
                  M550 P"MultiTool Cartesian"                                  ; set printer name
                  
                  ; Network
                  M552 P0.0.0.0 S1                                             ; enable network and acquire dynamic address via DHCP
                  M586 P0 S1                                                   ; enable HTTP
                  M586 P1 S0                                                   ; disable FTP
                  M586 P2 S0                                                   ; disable Telnet
                  
                  ; Drives
                  M569 P0.0 S1                                                 ; physical drive 0.0 goes forwards
                  M569 P0.1 S1                                                 ; physical drive 0.1 goes forwards
                  M569 P0.2 S1                                                 ; physical drive 0.2 goes forwards
                  M569 P1.0 S1                                                 ; physical drive 1.0 goes forwards
                  M569 P2.0 S1                                                 ; physical drive 2.0 goes forwards
                  M584 X0.0 Y0.1 Z0.2 E1.0:2.0                                 ; set drive mapping
                  M350 X256 Y256 Z256 E256:256 I0                              ; configure microstepping without interpolation
                  M92 X80.00 Y80.00 Z400.00 E420.00:420.00                     ; set steps per mm
                  M566 X900.00 Y900.00 Z60.00 E120.00:120.00                   ; set maximum instantaneous speed changes (mm/min)
                  M203 X31800.00 Y31800.00 Z31800.00 E1200.00:1200.00          ; set maximum speeds (mm/min)
                  M201 X500.00 Y500.00 Z20.00 E250.00:250.00                   ; set accelerations (mm/s^2)
                  M906 X800 Y800 Z800 E800:800                                 ; set motor currents (mA)
                  M84 S0                                                       ; Disable motor idle current reduction
                  
                  ; Axis Limits
                  M208 X0 Y0 Z0 S1                                             ; set axis minima
                  M208 X1000 Y1000 Z800 S0                                     ; set axis maxima
                  
                  ; Endstops
                  ; WARNING: No endstops configured
                  
                  ; Z-Probe
                  M558 P0 H5 F120 T6000                                        ; disable Z probe but set dive height, probe speed and travel speed
                  M557 X20:980 Y20:980 S80                                     ; define mesh grid
                  
                  ; Heaters
                  M308 S0 P"temp0" Y"thermistor" T100000 B4138                 ; configure sensor 0 as thermistor on pin temp0
                  M950 H0 C"out0" T0                                           ; create bed heater output on out0 and map it to sensor 0
                  M307 H0 B0 S1.00                                             ; disable bang-bang mode for the bed heater and set PWM limit
                  M140 H0                                                      ; map heated bed to heater 0
                  M143 H0 S120                                                 ; set temperature limit for heater 0 to 120C
                  M308 S1 P"121.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin 121.temp0
                  M950 H1 C"121.out0" T1                                       ; create nozzle heater output on 121.out0 and map it to sensor 1
                  M307 H1 B0 S1.00                                             ; disable bang-bang mode for heater  and set PWM limit
                  M143 H1 S280                                                 ; set temperature limit for heater 1 to 280C
                  M308 S2 P"122.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 2 as thermistor on pin 122.temp0
                  M950 H2 C"122.out0" T2                                       ; create nozzle heater output on 122.out0 and map it to sensor 2
                  M307 H2 B0 S1.00                                             ; disable bang-bang mode for heater  and set PWM limit
                  M143 H2 S280                                                 ; set temperature limit for heater 2 to 280C
                  
                  ; Fans
                  M950 F0 C"121.out2" Q500                                     ; create fan 0 on pin 121.out2 and set its frequency
                  M106 P0 S0 H1 T100                                           ; set fan 0 value. Thermostatic control is turned on
                  M950 F1 C"122.out2" Q500                                     ; create fan 1 on pin 122.out2 and set its frequency
                  M106 P1 S0 H2 T100                                           ; set fan 1 value. Thermostatic control is turned on
                  
                  ; Tools
                  M563 P0 S"Extrudeur 0" D0 H1 F0                              ; define tool 0
                  G10 P0 X0 Y0 Z0                                              ; set tool 0 axis offsets
                  G10 P0 R0 S0                                                 ; set initial tool 0 active and standby temperatures to 0C
                  M563 P1 S"Extrudeur 1" D1 H2 F1                              ; define tool 1
                  G10 P1 X0 Y0 Z0                                              ; set tool 1 axis offsets
                  G10 P1 R0 S0                                                 ; set initial tool 1 active and standby temperatures to 0C
                  M563 P2 S"Spindle" F-1                                       ; define tool 2
                  G10 P2 X0 Y0 Z0                                              ; set tool 2 axis offsets
                  G10 P2 R0 S0                                                 ; set initial tool 2 active and standby temperatures to 0C
                  
                  ; Custom settings are not defined
                  
                  ; Miscellaneous
                  M501                                                         ; load saved parameters from non-volatile memory
                  
                  
                  Vetiundefined 1 Reply Last reply Reply Quote 0
                  • Vetiundefined
                    Veti @Pseud3mys
                    last edited by

                    @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                    for the heating a fault accure 2 or 3 sec after the start.

                    what is the error message for that.

                    M350 X256 Y256 Z256 E256:256 I0

                    this will overload your cpu. switch back to x16 and interpolation.

                    M203 X31800.00 Y31800.00 Z31800.00 E1200.00:1200.00

                    are you sure thats the maximum speed you printer can achieve?

                    M906 X800 Y800 Z800 E800:800 ; set motor currents (mA)

                    these values are most likely wrong. you need to enter 75% of the rated current for each motor.

                    ; Endstops

                    ; WARNING: No endstops configured

                    you need to fix this

                    Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                    • Pseud3mysundefined
                      Pseud3mys
                      last edited by

                      I allowed the cold extrusion. I can now extrude but when I do it nothing happen.
                      For the heating, the thermistor return the right temperature. But I still have "fault" few second after I turn ON the heater.

                      Vetiundefined 1 Reply Last reply Reply Quote 0
                      • Vetiundefined
                        Veti @Pseud3mys
                        last edited by

                        @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                        But I still have "fault" few second after I turn ON the heater.

                        we need to know what the error message is.

                        Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti
                          last edited by

                          btw are you on firmware 3.1.1 ?

                          Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                          • Pseud3mysundefined
                            Pseud3mys @Veti
                            last edited by

                            @Veti

                            are you sure thats the maximum speed you printer can achieve?

                            No, I didn't begin setting up this part. Now, I just try to set up the dual extrudeur and hotends.

                            1 Reply Last reply Reply Quote 0
                            • Pseud3mysundefined
                              Pseud3mys @Veti
                              last edited by

                              @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                              btw are you on firmware 3.1.1 ?

                              yes

                              1 Reply Last reply Reply Quote 0
                              • Pseud3mysundefined
                                Pseud3mys @Veti
                                last edited by

                                @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                we need to know what the error message is.

                                I understood, but I have no error message or I don't now where i can see it.
                                Capture.PNG
                                I click on "Heater 2". It turn active, and after fews seconds It turn "fault" as you can see on the picture. But I have no error (even in the consol)

                                1 Reply Last reply Reply Quote 0
                                • Vetiundefined
                                  Veti
                                  last edited by

                                  you can find the error messages in the console or in the popup at the bottom right when they occur.

                                  Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                  • Pseud3mysundefined
                                    Pseud3mys @Veti
                                    last edited by

                                    @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                    you can find the error messages in the console or in the popup at the bottom right when they occur.

                                    I just tested but I don't have any error message (I checked the console and there is no pupop when it stop working)

                                    1 Reply Last reply Reply Quote 0
                                    • Vetiundefined
                                      Veti
                                      last edited by

                                      are you on duet web control 3.1.1 as well?

                                      Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                      • Pseud3mysundefined
                                        Pseud3mys @Veti
                                        last edited by

                                        @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                        are you on duet web control 3.1.1 as well?

                                        I think yes, what is the command to check ?

                                        1 Reply Last reply Reply Quote 0
                                        • Vetiundefined
                                          Veti
                                          last edited by

                                          on the general tab

                                          d8fa64d4-ada3-4d30-a846-ed9bee35d291-image.png

                                          Pseud3mysundefined 2 Replies Last reply Reply Quote 0
                                          • Pseud3mysundefined
                                            Pseud3mys @Veti
                                            last edited by

                                            @Veti ok, yes it both version 3.1.1

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA