Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    ToolBoard: 2 wires fan, heater fault and how to extrude ?

    Scheduled Pinned Locked Moved Unsolved
    Duet Hardware and wiring
    6
    112
    5.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Vetiundefined
      Veti @Pseud3mys
      last edited by

      @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

      for the heating a fault accure 2 or 3 sec after the start.

      what is the error message for that.

      M350 X256 Y256 Z256 E256:256 I0

      this will overload your cpu. switch back to x16 and interpolation.

      M203 X31800.00 Y31800.00 Z31800.00 E1200.00:1200.00

      are you sure thats the maximum speed you printer can achieve?

      M906 X800 Y800 Z800 E800:800 ; set motor currents (mA)

      these values are most likely wrong. you need to enter 75% of the rated current for each motor.

      ; Endstops

      ; WARNING: No endstops configured

      you need to fix this

      Pseud3mysundefined 1 Reply Last reply Reply Quote 0
      • Pseud3mysundefined
        Pseud3mys
        last edited by

        I allowed the cold extrusion. I can now extrude but when I do it nothing happen.
        For the heating, the thermistor return the right temperature. But I still have "fault" few second after I turn ON the heater.

        Vetiundefined 1 Reply Last reply Reply Quote 0
        • Vetiundefined
          Veti @Pseud3mys
          last edited by

          @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

          But I still have "fault" few second after I turn ON the heater.

          we need to know what the error message is.

          Pseud3mysundefined 1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti
            last edited by

            btw are you on firmware 3.1.1 ?

            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
            • Pseud3mysundefined
              Pseud3mys @Veti
              last edited by

              @Veti

              are you sure thats the maximum speed you printer can achieve?

              No, I didn't begin setting up this part. Now, I just try to set up the dual extrudeur and hotends.

              1 Reply Last reply Reply Quote 0
              • Pseud3mysundefined
                Pseud3mys @Veti
                last edited by

                @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                btw are you on firmware 3.1.1 ?

                yes

                1 Reply Last reply Reply Quote 0
                • Pseud3mysundefined
                  Pseud3mys @Veti
                  last edited by

                  @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                  we need to know what the error message is.

                  I understood, but I have no error message or I don't now where i can see it.
                  Capture.PNG
                  I click on "Heater 2". It turn active, and after fews seconds It turn "fault" as you can see on the picture. But I have no error (even in the consol)

                  1 Reply Last reply Reply Quote 0
                  • Vetiundefined
                    Veti
                    last edited by

                    you can find the error messages in the console or in the popup at the bottom right when they occur.

                    Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                    • Pseud3mysundefined
                      Pseud3mys @Veti
                      last edited by

                      @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                      you can find the error messages in the console or in the popup at the bottom right when they occur.

                      I just tested but I don't have any error message (I checked the console and there is no pupop when it stop working)

                      1 Reply Last reply Reply Quote 0
                      • Vetiundefined
                        Veti
                        last edited by

                        are you on duet web control 3.1.1 as well?

                        Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                        • Pseud3mysundefined
                          Pseud3mys @Veti
                          last edited by

                          @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                          are you on duet web control 3.1.1 as well?

                          I think yes, what is the command to check ?

                          1 Reply Last reply Reply Quote 0
                          • Vetiundefined
                            Veti
                            last edited by

                            on the general tab

                            d8fa64d4-ada3-4d30-a846-ed9bee35d291-image.png

                            Pseud3mysundefined 2 Replies Last reply Reply Quote 0
                            • Pseud3mysundefined
                              Pseud3mys @Veti
                              last edited by

                              @Veti ok, yes it both version 3.1.1

                              1 Reply Last reply Reply Quote 0
                              • Pseud3mysundefined
                                Pseud3mys @Veti
                                last edited by

                                @Veti I tried to update the toolBoard but I go this error:

                                02/12/2020 à 18:23:25	Upload of Duet3Firmware_TOOL1LC.bin successful after 1s
                                02/12/2020 à 18:23:27	M997 B122
                                Board 122 starting firmware update
                                02/12/2020 à 18:23:37	M997 S
                                Error: Failed to switch off remote heater 2: Board 122 does not have heater 2
                                02/12/2020 à 18:23:39	Error: Failed to switch off remote heater 2: Board 122 does not have heater 2
                                02/12/2020 à 18:24:06	Connection established
                                
                                Vetiundefined 1 Reply Last reply Reply Quote 0
                                • Pseud3mysundefined
                                  Pseud3mys
                                  last edited by

                                  I seem to have update it.. no error. But the version it's still 3.1.0 (on the toolboard 1LC). but I download the 3.1.1 (git hub)

                                  1 Reply Last reply Reply Quote 0
                                  • Vetiundefined
                                    Veti @Pseud3mys
                                    last edited by

                                    3.1.0 is correct there is no 3.1.1 for the toolboard.

                                    Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                    • Pseud3mysundefined
                                      Pseud3mys @Veti
                                      last edited by

                                      @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                      3.1.0 is correct there is no 3.1.1 for the toolboard.

                                      ah ok. Have you an idea then for the fault state ?

                                      1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti
                                        last edited by Veti

                                        @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                        Error: Failed to switch off remote heater 2: Board 122 does not have heater 2

                                        do you still get this error message?

                                        Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                        • Pseud3mysundefined
                                          Pseud3mys @Veti
                                          last edited by

                                          @Veti no, when I update it now it just put "2000°C" and offline on the web site but he is still connected with the CAN bus

                                          1 Reply Last reply Reply Quote 0
                                          • Vetiundefined
                                            Veti
                                            last edited by

                                            post the output of
                                            M122 B121
                                            and
                                            M122 B122

                                            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA