Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Distribution & Toolboard connection Problems

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    39
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • dc42undefined
      dc42 administrators
      last edited by

      Is the fuse on the tool board for that output intact?

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      Frederikundefined 1 Reply Last reply Reply Quote 0
      • Frederikundefined
        Frederik @dc42
        last edited by

        @dc42 Do you mean the Fuse on the Tool Distribution Board ?
        It is ok. I also tried another Port, but the same. No LEDs or other signs of life 😞

        Regards Frederik

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          I suggest you use a multimeter to check that you have +24V on the +VIN pin of the VIN connector on the tool board with respect to the ground pin.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          Frederikundefined 2 Replies Last reply Reply Quote 0
          • Frederikundefined
            Frederik @dc42
            last edited by

            @dc42 I checked it, 24V is ok on the tool and distribution board. Polarity is correct

            1 Reply Last reply Reply Quote 0
            • Frederikundefined
              Frederik @dc42
              last edited by

              @dc42 i used a stright trough 4 pin can cable

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators
                last edited by dc42

                Even without the CAN cable, with VIN power applied to the tool board you should get 2 LEDs lit and another one flashing. Please post photos showing how 24V power is supplied to VIN on the tool board.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                Frederikundefined 2 Replies Last reply Reply Quote 0
                • Frederikundefined
                  Frederik @dc42
                  last edited by

                  @dc42 as soon as i am back from Work, i will post pictures.

                  1 Reply Last reply Reply Quote 0
                  • Frederikundefined
                    Frederik @dc42
                    last edited by

                    @dc42 I supplied the Vin direct from my 24v power supply to the Vin of the tool distribution board. And from there with the first port to the toolboard lc1. I need 2 more hours at my office. I will send you the pictures as soon as I am at home. Could I test some other parts with my multimeter to check the correct function?

                    Regards
                    Frederik

                    1 Reply Last reply Reply Quote 0
                    • Frederikundefined
                      Frederik
                      last edited by

                      I checked the connections and fuses with the multimeter. Everything ok. 24.1v on the toolboard. But no led are on.!IMG_20201209_191716.jpg

                      1 Reply Last reply Reply Quote 0
                      • Frederikundefined
                        Frederik
                        last edited by

                        IMG_20201209_191938.jpg

                        1 Reply Last reply Reply Quote 0
                        • Frederikundefined
                          Frederik
                          last edited by Frederik

                          @dc42 Thank you, Problem Solved.
                          I rewired the distro and toolboard + making new crimps for my vin cables.

                          i was measuring the 24v on the bottom of the connector and checked the polarity.
                          But somehow the connection made no contact to the toolboard.when plugged in
                          I also updated my duet3 to RRF 3.2beta4.1

                          now the blue led is on and the red led is constantly on like the diag led on the duet 3, but not flashing. Is the firmware wrong?
                          What is the next thing to check?
                          Pressing the 2 buttons while starting the board doesn't change the led signals.

                          Is there another way to reset the toolboard and check the CAN connection?
                          Regards
                          FrederikIMG_20201210_024455.jpg

                          1 Reply Last reply Reply Quote 0
                          • A Former User?
                            A Former User
                            last edited by

                            it might not matter, but the tool distribution board you showed is missing a bypass jumper on the 4th unused output and doesn't show the jumper for the 1st you're actually using.

                            Frederikundefined 1 Reply Last reply Reply Quote 1
                            • Frederikundefined
                              Frederik @A Former User
                              last edited by Frederik

                              @bearer thanks for pointing that out. I uploaded the wrong photo. The jumpers are both removed from the first port with the cable and are set in every else slot.IMG_20201210_061343.jpg

                              I test both ways. With only one of the two jumpers removed and both jumpers removed. The same result in the console and no change in led behavior.

                              1 Reply Last reply Reply Quote 0
                              • Frederikundefined
                                Frederik
                                last edited by

                                M122
                                === Diagnostics ===
                                RepRapFirmware for Duet 3 MB6HC version 3.2-beta4 running on Duet 3 MB6HC v1.01 or later (SBC mode)
                                Board ID: 08DJM-956BA-NA3TN-6J9DL-3S46S-99AUT
                                Used output buffers: 1 of 40 (11 max)
                                === RTOS ===
                                Static ram: 123212
                                Dynamic ram: 138092 of which 24 recycled
                                Never used RAM 130864, free system stack 200 words
                                Tasks: Linux(ready,101) HEAT(blocked,298) CanReceiv(blocked,947) CanSender(blocked,371) CanClock(blocked,356) TMC(blocked,54) MAIN(running,1189) IDLE(ready,19)
                                Owned mutexes: HTTP(MAIN)
                                === Platform ===
                                Last reset 00:01:10 ago, cause: power up
                                Last software reset at 2020-12-10 01:00, reason: User, GCodes spinning, available RAM 130864, slot 2
                                Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0xffffffff Task Linu
                                Error status: 0x00
                                MCU temperature: min 26.1, current 35.2, max 35.3
                                Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
                                12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
                                Driver 0: position 0, standstill, reads 21528, writes 14 timeouts 0, SG min/max 0/0
                                Driver 1: position 0, standstill, reads 21529, writes 14 timeouts 0, SG min/max 0/0
                                Driver 2: position 0, standstill, reads 21530, writes 14 timeouts 0, SG min/max 0/0
                                Driver 3: position 0, standstill, reads 21533, writes 11 timeouts 0, SG min/max 0/0
                                Driver 4: position 0, standstill, reads 21534, writes 11 timeouts 0, SG min/max 0/0
                                Driver 5: position 0, standstill, reads 21532, writes 14 timeouts 0, SG min/max 0/0
                                Date/time: 2020-12-10 06:17:24
                                Slowest loop: 0.90ms; fastest: 0.12ms
                                === Storage ===
                                Free file entries: 10
                                SD card 0 not detected, interface speed: 37.5MBytes/sec
                                SD card longest read time 0.0ms, write time 0.0ms, max retries 0
                                === Move ===
                                Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
                                Bed compensation in use: none, comp offset 0.000
                                === MainDDARing ===
                                Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                                === AuxDDARing ===
                                Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                                === Heat ===
                                Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
                                === GCodes ===
                                Segments left: 0
                                Movement lock held by null
                                HTTP* is doing "M122" in state(s) 0
                                Telnet is idle in state(s) 0
                                File is idle in state(s) 0
                                USB is idle in state(s) 0
                                Aux is idle in state(s) 0
                                Trigger* is idle in state(s) 0
                                Queue is idle in state(s) 0
                                LCD is idle in state(s) 0
                                SBC is idle in state(s) 0
                                Daemon is idle in state(s) 0
                                Aux2 is idle in state(s) 0
                                Autopause is idle in state(s) 0
                                Code queue is empty.
                                === CAN ===
                                Messages queued 158, send timeouts 510, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 47
                                === SBC interface ===
                                State: 0, failed transfers: 0
                                Last transfer: 19ms ago
                                RX/TX seq numbers: 1334/1335
                                SPI underruns 0, overruns 0
                                Number of disconnects: 0, IAP RAM available 0x20a28
                                Buffer RX/TX: 0/0-0
                                === Duet Control Server ===
                                Duet Control Server v3.2.0-beta4
                                Code buffer space: 4096
                                Configured SPI speed: 8000000 Hz
                                Full transfers per second: 0.11
                                
                                Vetiundefined 1 Reply Last reply Reply Quote 0
                                • Frederikundefined
                                  Frederik
                                  last edited by Frederik

                                  M997 B121 S3
                                  Error: M997: Response timeout: CAN addr 121, req type 6024, RID=14
                                  

                                  everything I try only generates this timeouts. M115, M122, M997... Are there other parts to test with the multimeter to ensure that I got a working unit?

                                  1 Reply Last reply Reply Quote 0
                                  • Vetiundefined
                                    Veti @Frederik
                                    last edited by

                                    @Frederik said in Distribution & Toolboard connection Problems:

                                    Messages queued 158, send timeouts 510,

                                    this would indicate that there is something wrong with your can wiring.

                                    Frederikundefined 1 Reply Last reply Reply Quote 0
                                    • Frederikundefined
                                      Frederik @Veti
                                      last edited by

                                      @Veti I use a straight through 4 pin can cable that I made with the lc1 connector pack

                                      1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti
                                        last edited by Veti

                                        have you done the simple setup and tested that?

                                        https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/IgXsNbOKcEAWjeNO.huge

                                        also check the continuity of your can wiring. a bad crimp here will also be a headache.

                                        Frederikundefined 1 Reply Last reply Reply Quote 0
                                        • Frederikundefined
                                          Frederik @Veti
                                          last edited by

                                          @Veti I would try if I'd had a 120ohm resistor and a spare rj11 cable at Hand. I can source a bunch of those resistors later at my local electro shop.

                                          1 Reply Last reply Reply Quote 0
                                          • Frederikundefined
                                            Frederik
                                            last edited by

                                            @Veti i checked for continuity with the multimeter. Seems to be OK

                                            Vetiundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA