Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Z axis wont home

    Scheduled Pinned Locked Moved
    General Discussion
    5
    25
    3.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • brianundefined
      brian
      last edited by

      @dc42:

      Does the red LED on the sensor light up when the sensor is triggered i.e. close to the bed, and stay off otherwise? If yes and you are getting those readings around 900 then that suggests a faulty connection between the sensor output pin and the Duet.

      No it doesnt. It flashes twice on start up only.

      1 Reply Last reply Reply Quote 0
      • dc42undefined
        dc42 administrators
        last edited by

        That's not right. If you have connected it correctly then it should flash 4 times at startup. Perhaps you have connected the sensor output wire to the MOD pin of the Z probe connector instead of to the IN pin?

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        1 Reply Last reply Reply Quote 0
        • brianundefined
          brian
          last edited by

          Z-endstop engaged = @ not stopped * this changed
          Z-endstop released = @ min stop
          Z-probe activated (bed close enough to trigger it) = @ min stop
          Z-probe released (bed far enough away to not trigger it) = @ min stop

          1 Reply Last reply Reply Quote 0
          • brianundefined
            brian
            last edited by

            @dc42:

            That's not right. If you have connected it correctly then it should flash 4 times at startup. Perhaps you have connected the sensor output wire to the MOD pin of the Z probe connector instead of to the IN pin?

            I've connected sensor duetwifi
            power to 3.3v
            grnd to mod
            –-- grnd
            analogue probe in

            Looks like i've got Grnd on sensor going to Mod on duet.

            1 Reply Last reply Reply Quote 0
            • elmoretundefined
              elmoret
              last edited by

              @brian:

              Z-endstop engaged = @ not stopped * this changed
              Z-endstop released = @ min stop
              Z-probe activated (bed close enough to trigger it) = @ min stop
              Z-probe released (bed far enough away to not trigger it) = @ min stop

              This is a step in the right direction, but it seems as though that switch is active low, not active high. I assumed all three endstop switches were the same but is seems that is not the case. Try changing this:

              M574 X1 Y1 Z1 S1 ; Define active high microswitches

              to:

              M574 Z1 S0 ; Define active low microswitches
              M574 X1 Y1 S1 ; Define active high microswitches

              That should set the firmware up to expect an active low microswitch on Z. The above code also assumes your endstop is at the Z-minimum, if it is at the Z-maximum then change to Z2 instead of Z1.

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators
                last edited by

                Tim, thanks for that. Brian, you had better talk to aus3d if you are using their sensor. It's my sensor (also so!d by Duet3D and Filastruder) that should flash 4 times at startup when connected to a Duet.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • brianundefined
                  brian
                  last edited by

                  @dc42:

                  Tim, thanks for that. Brian, you had better talk to aus3d if you are using their sensor. It's my sensor (also so!d by Duet3D and Filastruder) that should flash 4 times at startup when connected to a Duet.

                  I think i have found the error, as i've mount the duet upside down, and with small print its hard to see clearly. I'll check until i'm convinced i see it right.

                  1 Reply Last reply Reply Quote 0
                  • brianundefined
                    brian
                    last edited by

                    I changed the ground on the sensor to the next position on the duet .

                    It still only flashes twice on start up, but when bed approches the sensor a red led lights up until bed is moved away.

                    1 Reply Last reply Reply Quote 0
                    • brianundefined
                      brian
                      last edited by

                      Now the home z only moves the bed down a bit, but the home all works!!!

                      1 Reply Last reply Reply Quote 0
                      • brianundefined
                        brian
                        last edited by

                        Finally got the z probe offset to work, it resisted a lot, but is good now.

                        Just want to thank dc42, elmoret, and CaLviNx for getting me thru this.

                        1 Reply Last reply Reply Quote 0
                        • fcwiltundefined
                          fcwilt
                          last edited by

                          Just love a happy ending.

                          Frederick

                          Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA