RRF3.2Beta4.1 Heightmap vs. Spindle/Driver Mapping

Frederik

@3dML its probing with 1mm/s. is that slow enough ?

The Last G32 after changing the settings

Leadscrew adjustments made: 0.380 0.168 0.089, points used 3, (mean, deviation) before (0.244, 0.085) after (0.000, 0.000)
Leadscrew adjustments made: 0.064 -0.009 -0.213, points used 3, (mean, deviation) before (-0.044, 0.083) after (0.000, 0.000)

Leadscrew adjustments made: 0.215 0.207 -0.272, points used 3, (mean, deviation) before (0.044, 0.169) after (0.000, 0.000)
Leadscrew adjustments made: 0.011 0.098 -0.100, points used 3, (mean, deviation) before (-0.013, 0.066) after (0.000, 0.000)

Leadscrew adjustments made: -0.087 0.158 0.672, points used 3, (mean, deviation) before (0.216, 0.222) after (-0.000, 0.000)
Leadscrew adjustments made: -0.018 -0.124 0.255, points used 3, (mean, deviation) before (0.060, 0.126) after (-0.000, 0.000)

Leadscrew adjustments made: 0.305 0.199 0.353, points used 3, (mean, deviation) before (0.304, 0.054) after (-0.000, 0.000)
Leadscrew adjustments made: 0.017 -0.064 0.012, points used 3, (mean, deviation) before (0.002, 0.031) after (0.000, 0.000)

Leadscrew adjustments made: 0.278 0.250 0.293, points used 3, (mean, deviation) before (0.279, 0.015) after (0.000, 0.000)
Leadscrew adjustments made: 0.012 -0.013 -0.004, points used 3, (mean, deviation) before (0.003, 0.008) after (0.000, 0.000)

Leadscrew adjustments made: 0.264 0.270 0.289, points used 3, (mean, deviation) before (0.274, 0.008) after (0.000, 0.000)
Leadscrew adjustments made: 0.011 -0.011 -0.009, points used 3, (mean, deviation) before (0.000, 0.007) after (0.000, 0.000)

G29
81 points probed, min error -0.806, max error 0.757, mean -0.124, deviation 0.338
Height map saved to file heightmap.csv

xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
50.00,400.00,50.00,390.00,-1.00,38.90,37.80,9,9
 -0.028, -0.333, -0.536, -0.719, -0.794, -0.806, -0.694, -0.498, -0.213
  0.086, -0.210, -0.423, -0.591, -0.686, -0.655, -0.535, -0.386, -0.109
  0.123, -0.133, -0.348, -0.498, -0.593, -0.561, -0.411, -0.277, -0.096
  0.277, -0.020, -0.213, -0.400, -0.465, -0.453, -0.370, -0.169,  0.052
  0.300,  0.019, -0.156, -0.299, -0.374, -0.309, -0.263, -0.114,  0.103
  0.395,  0.137, -0.045, -0.197, -0.278, -0.281, -0.146, -0.010,  0.215
  0.523,  0.232,  0.018, -0.110, -0.236, -0.192, -0.128,  0.062,  0.233
  0.651,  0.365,  0.130, -0.022, -0.146, -0.135, -0.048,  0.122,  0.346
  0.757,  0.547,  0.280,  0.062, -0.042, -0.017,  0.075,  0.206,  0.420

RepRapFirmware height map file v2 generated at 2020-12-23 01:13
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
45.00,410.00,40.00,390.00,-1.00,365.00,350.00,2,2
  0.423,  0.344
  1.333,  1.363

th last is a heightmap on the 4 corners as far out as possible

3dML

@Frederik
Yes if multiple G30 S-1 in the same spot return a very small variation these results mean the config is not correct.

If this is your only G31 this may be your problem. I just notice you have no X or Y offset for your BLTouch.

G31 P1000 X0 Y0 Z0.81

Frederik

@3dML is the offset measured from the nozzle or always from x0 y0 ?

3dML

@Frederik
G31 is the probe offset from the nozzle. If you position the nozzle at x0 y0 the G31 offset would be the position of the BLTouch.

Frederik

@3dML when my printhead is homed at x0 y0 (left front corner) the bltouch is around x-3 y-2
the nozzle x35 y8

this is are the values for another test with 4:4 Probing Points

xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
45.00,410.00,40.00,390.00,-1.00,121.67,116.67,4,4
  0.020, -0.735, -0.706, -0.097
  0.252, -0.427, -0.378,  0.354
  0.536, -0.148, -0.128,  0.676
  0.903,  0.127,  0.082,  0.945

3dML

@Frederik said in RRF3.2Beta4.1 Heightmap vs. Spindle/Driver Mapping:

@3dML when my printhead is homed at x0 y0 (left front corner) the bltouch is around x-3 y-2
the nozzle x35 y8

Post the files you use for homing. The DWC tool position should report the exact position of the nozzle.

3dML

@Phaedrux said in RRF3.2Beta4.1 Heightmap vs. Spindle/Driver Mapping:

M671 defines the position of the lead screws
The order must match the order of the motors defined in M584
In bed.g you probe as close to the lead screws as you can in the same order as the lead screws are defined.

Have you verified these settings are correct and the motors are positioned in the same order in the M671 as in the M584?

Frederik

@3dML

I added your if loop to a makro. Works almost perfekt.
Would it be possible that the measured values are displayed as message or in the console after each move? I stopped the makro after around 10min without knowing if the values are decreasing or what's happening

I checked the limits bevor and it's running.

I also tested several mesh sizes, the resulting height maps are above.

I think, these values are reasonable to some point, I sliced a X from center of the bed 350mm to the 4 corners with a 50x50 rectangular pattern 150mm from the center.

I increased the z trigger height to 1.81mm for safety and started a really slow test pattern. Today after Work I will verify it with a good old magnetic base + digital indicator on different spots along the gantry + x and y along he bed corners. Perhaps I can shim it, modifie the mounts or something else

Frederik

@Phaedrux
@3dML
left spindle is connected to 0.2
back center to 0.3
front right to 0.4

the wiring from the specified drivers to the spindles is correct
i map the Z steppers: Z02:03:04 - that should be ok

my homeall.g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 19 2020 21:32:05 GMT+0100 (Mitteleuropäische Normalzeit)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-425 Y-405 F6000 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-405             ; home X axis
G1 H1 Y-405             ; home Y axis
G1 X5 Y5 F6000          ; go back a few mm
G1 H1 X-425 F360        ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-405             ; then move slowly to Y axis endstop
G90                     ; absolute positioning
G1 X215 Y210 F6000      ; go to first bed probe point and home Z
G30                     ; home Z by probing the bed

homex.g

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 19 2020 21:32:05 GMT+0100 (Mitteleuropäische Normalzeit)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X-425 F6000 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 H1 X-425 F360  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

homey.g

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 19 2020 21:32:05 GMT+0100 (Mitteleuropäische Normalzeit)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position

G1 H1 Y-425 F6000 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000       ; go back a few mm
G1 H1 Y-425 F360  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F1000   ; lower Z again
G90               ; absolute positioning

homez.g:

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 19 2020 21:32:05 GMT+0100 (Mitteleuropäische Normalzeit)
G91                ; relative positioning
G1 H2 Z5 F1000     ; lift Z relative to current position
G90                ; absolute positioning
G1 X215 Y210 F6000 ; go to first probe point
G30                ; home Z by probing the bed

Phaedrux

Can you show an image marked up with where the motors driven by the 02,03,04 drivers are positioned?

3dML

@Frederik
Add an M291 between the M409 and the if statement. I have updated the macro below with this

M291 P{move.calibration.initial.deviation} S3

Based upon these values

M208 X0 Y0 Z0 S1                 ; set axis minima
M208 X415 Y395 Z400 S0           ; set axis maxima
G10 P0 X0 Y0 Z0                  ; set tool 0 axis offsets

the nozzle should be considered at x0 y0 and the BLTouch at x-38 y-10 in the comment below.

when my printhead is homed at x0 y0 (left front corner) the bltouch is around x-3 y-2

the nozzle x35 y8

This

G31 P1000 X0 Y0 Z0.81                                              ; BLTouch offset

should be updated to this

G31 P1000 X-38 Y-10 Z0.81                                              ; BLTouch offset

For M671 move the tool head to the position indicated by the (1) of x0 y(align the nozzle to the spindle). Measure from the center of the nozzle to the center of the spindle and subtract that number from x0. The Y value will be the Y position as indicated by the DWC tool position.

Next move tool head to position 2 of x(align the nozzle to the spindle) y395. Measure from the center of the nozzle to the center of the spindle and add that number to y395. The X value will be the X position as indicated by the DWC tool position.

Next move tool head to position 3 of x415 y(align the nozzle to the spindle). Measure from the center of the nozzle to the center of the spindle and add that number to x415. The Y value will be the Y position as indicated by the DWC tool position.

Update the M671 with the values collected from the above steps.

M671 X0:215:450 Y80:450:80 S5 				     ; Position of Leadscrews

Next copy your first G30 command from the 3point calibration

G30 P0 X40 Y80 Z-99999

to the console and send it the printer. Once the command has finished record the tool position as indicated by the DWC. Use this x and y value in a G1 x## y## command at the beginning of the 3point calibration followed by G30 to set the z height.

Update the 3point calibration macro to something like

M203 Z100 ; set a low z max speed to increase accuracy. Run multiple G30 S-1 to determine the speed needed to achieve the accuracy you need.  
G28
while true
        G1 X## Y## ; enter the tool position as indicated by the DWC after running the first G30 command in the 3point calibration
        G30 ; sets the first point of the 3point calibration as Z0
	G30 P0 X40 Y80 Z-99999          ; Probe near the front left lead-screw
        G30 P1 X215 Y395 Z-99999        ; Probe near the rear lead screw 
        G30 P2 X415 Y80 Z-99999 S3      ; Probe near the front right lead-screw
	M409 K"move.calibration.initial.deviation" ;displays deviation in console
        M400 ; wait for move to complete
        M291 P{move.calibration.initial.deviation} S3 ;displays deviation value
	if move.calibration.initial.deviation <= 0.001  ; change the 0.001 to your needed value
		echo "Passed"
                M203 Z1000 ; set this z max speed to match your config file. Note if you cancel this macro by selecting the cancel button on the M291 message box this command will not run. You will need to run this command from the console to restore the max z speed
		break
	continue

Follows these steps above to double check all your setting are correct. Lets the 3point calibration macro run until the deviation no longer decreases and post the results.

@Phaedrux
This is my understanding of the calibration process for 3 motor Z axis calibration.
If something is not correct please update it. This is the process I used to set mine up and it works perfectly.

Edit: {
Added M203 to start and end of macro to increase probe accuracy.

@3dML said in RRF3.2Beta4.1 Heightmap vs. Spindle/Driver Mapping:

@Frederik
I have found that slowing down the maximum Z speed can help with tolerance.

}

Frederik

@3dML @Phaedrux

this is the online fusion 360 CAD Model of my build. perhaps it helps to show the position oh everything and offsets ....

https://myhub.autodesk360.com/ue2c6242f/g/shares/SH56a43QTfd62c1cd9689aec54c27a170106

3dML

@Frederik
The drawing looks correct. My above post still applies.

Based on these values

M208 X0 Y0 Z0 S1                 ; set axis minima
M208 X415 Y395 Z400 S0           ; set axis maxima
G10 P0 X0 Y0 Z0                  ; set tool 0 axis offsets

all offsets are relative to nozzle position with the tool at x0 y0.

Base on that drawing and your height map I'd say the bed has a large sag along the Y axis.

alt text
In this image your 3point calibration deviation is close to 0 but the sag in the bed is causing the skew in the Heightmap.

Frederik

@3dML ok, i will post the values as soon as im finished. i will send the manufacturer a photo, perhaps its was damaged during shipping

Frederik

@3dML I will save 4 workspace positions on the outer corners so that i am always probing at the same spots, and check the mounting of the bed + possible options for what to improve...

right now it sits on 4 silicone pads.
i could change to springs or to 4 solid openbuild Blocks

@Phaedrux
position of spindles+mapping.png

V-Core Pro V1_snapshot.png

3dML

@Frederik
Post a picture of the current mount you are using to mount the bed to the z sub-frame. If you are using the mounts I think you are they may be be the cause of sum of the sag.

Frederik

@3dML Good Morning,

Merry Christmas

The last if loop after modifying the accel values of Z to 20 and max speed to 100

M98 P"0:/macros/1 test if loop - Z deviation new"
Leadscrew adjustments made: 0.351 -1.187 0.554, points used 3, (mean, deviation) before (0.049, 0.626) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.626}
Leadscrew adjustments made: 0.346 -0.771 0.107, points used 3, (mean, deviation) before (-0.010, 0.392) after (-0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.392}
Leadscrew adjustments made: 0.093 -0.459 0.023, points used 3, (mean, deviation) before (-0.066, 0.200) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.200}
Leadscrew adjustments made: 0.077 -0.390 -0.087, points used 3, (mean, deviation) before (-0.095, 0.158) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.158}
Leadscrew adjustments made: -0.032 -0.217 -0.052, points used 3, (mean, deviation) before (-0.084, 0.067) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.067}
Leadscrew adjustments made: -0.170 -0.222 -0.008, points used 3, (mean, deviation) before (-0.125, 0.068) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.068}
Leadscrew adjustments made: -0.142 -0.175 -0.105, points used 3, (mean, deviation) before (-0.137, 0.022) after (-0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.022}
Leadscrew adjustments made: -0.15 actual 2 -0.165 -0.158, points used 3, (mean, deviation) before (-0.157, 0.004) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.004}
Leadscrew adjustments made: -0.164 -0.177 -0.151, points used 3, (mean, deviation) before (-0.163, 0.008) after (-0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.008}
Leadscrew adjustments made: -0.182 -0.158 -0.160, points used 3, (mean, deviation) before (-0.168, 0.008) after (-0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.008}
Leadscrew adjustments made: -0.165 -0.169 -0.172, points used 3, (mean, deviation) before (-0.168, 0.002) after (0.000, 0.000)
{"key":"move.calibration.initial.deviation","flags":"","result":0.002}
Passed

My NOZZLE !!! is now x0 Y0, like you mentioned, and bltouch x-35 y-15 d, i would thay after looking at the different values, the measurements are getting overall closer and more consistent

@3dML

Yesterday i changed the mounting from silicone spacers back to the standard springs from the Kit. now its mounted 1:1 like the CAD above wiht 4 springs at the corners

Frederik

@3dML
the old mounting:
img_20201224_101915.jpg)

at the moment mounted with this original springs:

![IMG_20201224_101939.jpg]

The openbuild blocks:

the subframe assembly from the side:

on top is a Prima Creator Magnetic Flex Steel Plate
and the Keenovo Silicone Heatpad below + isolating padding

3dML

@Frederik
My guess is excessive force got applied to the center of the bed at some point and the nature of the L brackets with a single bolt allowed them to swivel inward creating the bend in the bed along the Y axis. I don't have any experience with that style of bed mount so not sure what would be the best recommendation for mounting.

Frederik

@3dML The Bed was shipped with DHL Express from Portugal to Germany. Perhaps it got damaged along the way?

What are the most thermal stable and least problematic solutions for the bed ?

i wanted to print a 3 or 4 point kinematic mount like the Hevort V2 without the need of a subframe . only 3x sfu1204 Spindles and a mgn12 or 15 rail behind to eliminate the ply of the floating mount (without FK/BK Blocks).

option 1: borosilikat plate 400x400mm without flex plate or similar
option 2. Aluminium Plate, 10-20mm thick with precision ground surface to +0.025 to -0.025 and flex plate or something like that

option 3 the same precision plate , only with a DIY coating with Ultem Pellets (PEI) solved in dichloromethane