• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

rrf3 trigger g30 s-1 problem

Scheduled Pinned Locked Moved
Duet Hardware and wiring
4
6
285
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    luca-f13
    last edited by 24 Dec 2020, 09:45

    Hello everyone I wish you happy holidays and to not let you get bored during Christmas I ask you my problem

    I went from release 2.05 to 3.1.1 in release 2.05 the commands to calibrate the Z 0 with my bltouch thinking it was child's play having already run it a thousand times.
    then I turn on the printer
    I launch the commands:
    g92 z0
    g1 z10
    g30 s-1

    as part of doing the check the error comes out

    G30 S-1
    Error: Z probe was not triggered during probing move

    cosa sto sbagliando?
    allego config.g
    config.g

    undefined 1 Reply Last reply 24 Dec 2020, 18:45 Reply Quote 0
    • undefined
      PCR
      last edited by 24 Dec 2020, 10:08

      post you config.g

      1 Reply Last reply Reply Quote 0
      • undefined
        luca-f13
        last edited by 24 Dec 2020, 10:17

        è allegato

        eccolo comunque

        ; Configuration file for Duet Maestro (firmware version 3)
        ; executed by the firmware on start-up
        ;
        ; generated by RepRapFirmware Configuration Tool v3.1.10 on Thu Dec 24 2020 09:57:02 GMT+0100 (Ora standard dell’Europa centrale)

        ; General preferences
        G90 ; send absolute coordinates...
        M83 ; ...but relative extruder moves
        M550 P"draw2-200" ; set printer name

        ; Network
        M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
        M586 P0 S1 ; enable HTTP
        M586 P1 S0 ; disable FTP
        M586 P2 S0 ; disable Telnet

        ; Drives
        M569 P0 S1 ; physical drive 0 goes forwards
        M569 P1 S0 ; physical drive 1 goes backwards
        M569 P2 S1 ; physical drive 2 goes forwards
        M569 P3 S0 ; physical drive 3 goes backwards
        M569 P4 S1 ; physical drive 4 goes forwards
        M584 X0 Y1 Z2 E3:4 ; set drive mapping
        M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
        M92 X100.00 Y100.00 Z400.00 E120.20:120.20 ; set steps per mm
        M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
        M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
        M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
        M906 X1000 Y1000 Z1400 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
        M84 S30 ; Set idle timeout

        ; Axis Limits
        M208 X0 Y0 Z0 S1 ; set axis minima
        M208 X220 Y220 Z200 S0 ; set axis maxima

        ; Endstops
        M574 X1 S1 P"!^xstop" ; configure active-high endstop for low end on X via pin !^xstop
        M574 Y1 S1 P"!^ystop" ; configure active-high endstop for low end on Y via pin !^ystop
        M574 Z1 S2 ; configure Z-probe endstop for low end on Z

        ; Z-Probe
        M950 S0 C"^zprobe.mod" ; create servo pin 0 for BLTouch
        M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
        G31 P500 X-28 Y-39.5 Z0.842 ; set Z probe trigger value, offset and trigger height
        M557 X20:200 Y20:200 S45 ; define mesh grid

        ; Heaters
        M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
        M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
        M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
        M140 H0 ; map heated bed to heater 0
        M143 H0 S100 ; set temperature limit for heater 0 to 100C
        M308 S1 P"e0temp" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin e0temp
        M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
        M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
        M143 H1 S280 ; set temperature limit for heater 1 to 280C
        M308 S2 P"e1temp" Y"thermistor" T100000 B3950 ; configure sensor 2 as thermistor on pin e1temp
        M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
        M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
        M143 H2 S280 ; set temperature limit for heater 2 to 280C

        ; Fans
        M950 F0 C"!fan0" Q500 ; create fan 0 on pin !fan0 and set its frequency
        M106 P0 S0 H0 T35 ; set fan 0 value. Thermostatic control is turned on
        M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
        M106 P1 S1 H1:2 T30 ; set fan 1 value. Thermostatic control is turned on
        M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
        M106 P2 S1 H2:1 T30 ; set fan 2 value. Thermostatic control is turned on

        ; Tools
        M563 P0 S"anteriore" D0 H1 F0:1 ; define tool 0
        G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
        M563 P1 S"posteriore" D1 H2 F0:2 ; define tool 1
        G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
        G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

        ; Custom settings
        ; DISPLAY
        M575 P1 S1 B57600
        ; config override.g
        M501

        1 Reply Last reply Reply Quote 0
        • undefined
          luca-f13
          last edited by 24 Dec 2020, 16:39

          NO ONE HAS UNDERSTOOD WHERE WRONG

          1 Reply Last reply Reply Quote 0
          • undefined
            Phaedrux Moderator @luca-f13
            last edited by 24 Dec 2020, 18:45

            @luca-f13 said in rrf3 trigger g30 s-1 problem:

            G30 S-1
            Error: Z probe was not triggered during probing move

            Does it trigger with a G30?

            Can you send M122 and M98 P"config.g" and post the results?

            Z-Bot CoreXY Build | Thingiverse Profile

            undefined 1 Reply Last reply 24 Dec 2020, 21:30 Reply Quote 0
            • undefined
              dc42 administrators @Phaedrux
              last edited by 24 Dec 2020, 21:30

              Does the bltouch pin deploy when you send M401 and retract when you send M402 ?

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              2 out of 6
              • First post
                2/6
                Last post
              Unless otherwise noted, all forum content is licensed under CC-BY-SA