*****OH MY GOD *****
I found the problem is neither electronic nor electrical the problem nor software
now I hope you don't get mad the problem is with the heater block holder.
the two heater block holders were made of two different materials one in steel and one in aluminum so the heat was struggling to spread in one case and in the other it spread quickly
I am very angry but at least I solved it.
thanks to everyone for the help
@Phaedrux said in duet maestro fw 2,05:
@luca-f13 said in duet maestro fw 2,05:
how do I access the configurator?
https://configtool.reprapfirmware.org/
This may prove useful as well since it's been so long.
https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet
thank you, you were very kind
@droftarts said in duet maestro fw 2,05:
if you still have access to DWC
how do I access the configurator??? DWC
@droftarts I should have the dwc somewhere if I remember how to access it. anyway yes I was referring to doing a firmware update to rrf 3.xxx I don't know which one
Now I'll try to access DWC and then we'll see, thank you
I own a Duet Maestro and I haven't had a hand in it for several years. Having decided to make substantial changes to the printer, I would like to know how to update the software while still having version 2.05 of the firmware.
I have BL Touch installed on the printer. Could I have problems doing this update?
where do I find the files to update?
thanks in advance for your answers.
NO ONE HAS UNDERSTOOD WHERE WRONG
è allegato
eccolo comunque
; Configuration file for Duet Maestro (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Thu Dec 24 2020 09:57:02 GMT+0100 (Ora standard dell’Europa centrale)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"draw2-200" ; set printer name
; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E120.20:120.20 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1400 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X220 Y220 Z200 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"!^xstop" ; configure active-high endstop for low end on X via pin !^xstop
M574 Y1 S1 P"!^ystop" ; configure active-high endstop for low end on Y via pin !^ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; Z-Probe
M950 S0 C"^zprobe.mod" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-28 Y-39.5 Z0.842 ; set Z probe trigger value, offset and trigger height
M557 X20:200 Y20:200 S45 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M308 S2 P"e1temp" Y"thermistor" T100000 B3950 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S280 ; set temperature limit for heater 2 to 280C
; Fans
M950 F0 C"!fan0" Q500 ; create fan 0 on pin !fan0 and set its frequency
M106 P0 S0 H0 T35 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1:2 T30 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H2:1 T30 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 S"anteriore" D0 H1 F0:1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"posteriore" D1 H2 F0:2 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
; Custom settings
; DISPLAY
M575 P1 S1 B57600
; config override.g
M501
Hello everyone I wish you happy holidays and to not let you get bored during Christmas I ask you my problem
I went from release 2.05 to 3.1.1 in release 2.05 the commands to calibrate the Z 0 with my bltouch thinking it was child's play having already run it a thousand times.
then I turn on the printer
I launch the commands:
g92 z0
g1 z10
g30 s-1
as part of doing the check the error comes out
G30 S-1
Error: Z probe was not triggered during probing move
cosa sto sbagliando?
allego config.g
config.g
*****OH MY GOD *****
I found the problem is neither electronic nor electrical the problem nor software
now I hope you don't get mad the problem is with the heater block holder.
the two heater block holders were made of two different materials one in steel and one in aluminum so the heat was struggling to spread in one case and in the other it spread quickly
I am very angry but at least I solved it.
thanks to everyone for the help
@engikeneer
I have 3950 thermistors but using those proposed in the menu no one gives the possibility to the heater h1 to reach 210 degrees for the calibration test I have tried all those he offers me and this was the only one that allows me to finish the test
yes the two thermistors detected the same ambient temperature and also as values detected with the multimeter
no the h2 heater is the one that reaches 210 degrees in one minute the problem is h1 which takes about 7 minutes to reach the temperature with great difficulty
I am as perplexed as you are because there is no reason for these differences now I have ordered new heaters that I have just received in the afternoon I try to do everything with new ones then I will let you know the result
I am grateful for your precious help
@Phaedrux
they are two separate elements
PRUSAnew.PDF