Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Printing

    Scheduled Pinned Locked Moved
    Example setups and prints
    3
    13
    700
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Vetiundefined
      Veti
      last edited by

      @Dodger said in Printing:

      confConfiguration file for Duet 0.6 (firmware version 1.21)

      what duet do you have?
      apparently you selected duet 1 in the config tool, yet you write you have a duet 2.

      what firmware version are you running?
      if you are starting new and you have a duet 2 you should update to firmware 3.11.
      see https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
      do not forget to update the wifi firmware and the duet web control.

      easiest is to update using bossa if you have a very old version.

      then go through these steps.
      https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

      Dodgerundefined 1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator @Dodger
        last edited by

        @Dodger said in Printing:

        I cannot open the web page

        How are you trying to connect?
        What IP address does the Duet have?
        As this is a wifi, how have you added the SSID and password?

        Z-Bot CoreXY Build | Thingiverse Profile

        Dodgerundefined 1 Reply Last reply Reply Quote 0
        • Dodgerundefined
          Dodger @Veti
          last edited by

          @Veti the config may say it is for a duet o.6 but has been heavily modified. My firmware is 2.05

          1 Reply Last reply Reply Quote 0
          • Dodgerundefined
            Dodger @Phaedrux
            last edited by

            @Phaedrux Long, rather weary, story. I thought I had fried my ethernet duet 2 so bought a wifi one. After a while I got a config file that appeared to do what it should so put it back in the ethernet board. I connected through YAT and for the first time got an IP address, I have now connected direct to my router and the USB cable and the web console actually opens but there is an error message. "Failed to get file list"" directory 0:/macros not found

            Vetiundefined 1 Reply Last reply Reply Quote 0
            • Vetiundefined
              Veti @Dodger
              last edited by

              @Dodger said in Printing:

              directory 0:/macros

              just create that folder on the sd card
              see
              https://duet3d.dozuki.com/Wiki/SD_Card

              Dodgerundefined 1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                When you have a USB terminal up please send M122 and M98 P"config.g" and post the results.

                What do you have on your SD card? It sounds like you're missing the directory structure. Are you perhaps also missing the web interface files as well?

                https://duet3d.dozuki.com/Wiki/SD_Card#Section_Creating_the_file_structure

                Z-Bot CoreXY Build | Thingiverse Profile

                Dodgerundefined 1 Reply Last reply Reply Quote 0
                • Dodgerundefined
                  Dodger @Phaedrux
                  last edited by

                  @Phaedrux Yes I am probably missing something . I have inputted 'Duet2CombinedFirmware.bin' and confirmed that I have 2.05.1 entered. I have also loaded 'iap4e.bin'but I think need a web control input.

                  I suspect that my sys file is in a bit of a mess so will start from the beginning

                  1 Reply Last reply Reply Quote 0
                  • Dodgerundefined
                    Dodger @Veti
                    last edited by

                    @Veti OK so I create a folder but where do the files for that folder come from,?

                    Vetiundefined 1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti @Dodger
                      last edited by

                      @Dodger

                      thats where your macros go

                      Dodgerundefined 1 Reply Last reply Reply Quote 0
                      • Dodgerundefined
                        Dodger @Veti
                        last edited by

                        @Veti thanks that seems to have done it

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA