New stable firmware bundle 3.2 released

PeterH1500

Thank you for your hard work in producing this update.

Unfortunately, I have a problem when attempting to install RRF 3.2 that results in the following error message -

Error: M997: In-application programming binary "Duet2CombinedIAP.bin" not found.

Sure enough, a file named "Duet2CombinedIAP.bin" is not present in the downloaded "Duet2and3Firmware-3.2.zip".

Please could you advise what I should do?

I have a Duet 2 WiFi successfully running RRF3.1.1, & I've updated to DWC3.2. The "Duet2and3Firmware-3.2.zip" successfully uploads & unzips and I'm asked if I wish to install the new firmware.

Veti

@PeterH1500 said in New stable firmware bundle 3.2 released:

Error: M997: In-application programming binary "Duet2CombinedIAP.bin" not found.

its here
https://github.com/Duet3D/RepRapFirmware/releases/tag/3.0

it was part of the 3.0 update. if you went with bossa update, you might have missed it.

PeterH1500

@Veti Thank you. That worked (confirmed by M122).

I'd assumed from the upgrade instructions (Users running RepRapFirmware 3.0 or later should be able to upgrade by uploading file Duet2and3Firmware-3.2.zip. The individual files are also included here in case of difficulty.) that everything needed would either be in the "Duet2and3Firmware-3.2.zip" or in list . The list does not include a copy of "Duet2CombinedIAP.bin" and it doesn't seem to have been retained on my DUET SD card from my previous update to RRF3.0. But, my problem solved in double quick time. Thanks again.

MartinNYHC

Very nice that the PanelDue can be updated now via GCODE

A Former User

I like the "colour-coding" the most -> So much better when you have to put in a ton of comments if the client want´s it that way BIG THANKS

Dr_Ju_Ju

Thank you, the update went well, just dragging & dropping the combined zip file onto the UI, just 2 'niggles', 1. the UI 'lost' the dark theme, & 2. clicking on the new "Files \ Display" icon in the left hand side, results in an error message:
"Failed to get file list
Directory 0:/menu not found"
neither of which is biggie & easily sorted !!

jmshep

Upgraded from 3.2RC and all went well except my webcam settings in DWC were corrupted. Amended missing / additional text and now working as before.

achrn

Thank you.

A minor thing (not really a problem, so not requiring anew thread, I think): if you run a heater tune for the bed, the consiole now gets a message e.g.:

09/01/2021, 12:52:41 	Edit the M307 H0 command in config.g to match this. Omit the V parameter if the heater is not powered from VIN.
09/01/2021, 12:52:41 	Auto tuning heater 0 completed after 3 idle and 5 tuning cycles in 2931 seconds. This heater needs the following M307 command:
                        M307 H0 R0.243 C1266.3 D46.33 S1.00 V24.1

However, since the bed heater defaults to bang-bang, I think this should be advising to use a command that includes a B0 (assuming that's still the behaviour, if not, https://duet3d.dozuki.com/Wiki/Gcode#Section_M307_Set_or_report_heating_process_parameters needs an update).

amjm22

How long does it take to update the firmware? Mine has been going on for 40 minutes

dc42

It should be much quicker than that. I suggest you try refreshing the DWC browser page. If it still says that firmware updates are being installed, reboot the Duet.

amjm22

@dc42 Thanks! I held my breath, restarted and it came back on... Things were touch and go for a moment!

I appreciate all of the support, You guys are amazing

dc42

@amjm22 said in New stable firmware bundle 3.2 released:

@dc42 Thanks! I held my breath, restarted and it came back on... Things were touch and go for a moment!

I appreciate all of the support, You guys are amazing

Did the upgrade succeed? Use M115 to check the firmware version, or look in the Machine Specific tab of DWC.

amjm22

@dc42 Yes, it worked! Thanks

amjm22

When installing The Webserver to 3.2 I get this error -

RepRapFirmware for Duet 3 MB6HC version 3.2 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)

1/10/2021, 11:39:15 AM Failed to upload materialdesignicons-webfont.4187121a.woff2
Operation failed (Reason: Access to the path '/opt/dsf/sd/www/fonts/materialdesignicons-webfont.4187121a.woff2' is denied.)

Has anyone seen this before?

Tapetenhobel

Hi,
I update from a Duet2 Wifi to the new mini+ and hooked it to a raspberry pi.
A friend and me are currently developing a multi-Platform print monitor and I've used queries via /rr_status?type=2 and so on before, but with DWC running on the pi I only get a 404:Not found when I try to query DWC. It was running fine on the Duet2 with the beta and RC-versions. I also didn't found anything in the release notes regarding this.
Do I miss something?

Thanks

resam

@Tapetenhobel not really a v3.2 problem, or is it?

I think you are looking for the new API when running in "SBC mode" with DuetSoftwareFramework:
https://github.com/Duet3D/DuetSoftwareFramework#get-machinestatus

Phaedrux

@amjm22 How are you updating? If using the SBC you should be using sudo apt update/upgrade method.

amjm22

@Phaedrux - sudo apt update/upgrade. I did that, I'm still on Duet Web Control 3.1.1

Thanks for your reply

amjm22

@amjm22 I did again and it worked! unreal

Tapetenhobel

@resam
Cool, thanks