Artillery Genius Duet 2 Wifi Configuration

[Phaedrux]

@d0minik96 said in Artillery Genius Duet 2 Wifi Configuration:

tried to move the motors and when i move one axis all axis move. and not only that. i kinda switches directions.

Maybe post a video of what is happening as well as your current config.g and homing files.

[d0minik96]

Also Extruder temp is shown as 200 °C.

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Sat Jan 23 2021 18:37:34 GMT+0100 (Mitteleuropäische Normalzeit)
 
; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"Dominik's 3D"                           ; set printer name
M669 K2                                        ; select CoreXY mode
 
; Network
M551 P"test"                                   ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet
 
; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 Z16 I0                                    ; configure microstepping without interpolation
M350 X16 Y16 E16 I1                            ; configure microstepping with interpolation
M92 X80.121 Y80.121 Z399.78 E445.00              ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E300.00           ; set maximum instantaneous speed changes (mm/min)
M203 X1200.00 Y1200.00 Z150.00 E240.00        ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z20.00 E1500.00           ; set accelerations (mm/s^2)
M906 X1050 Y1050 Z1050 E600 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout
 
; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X220 Y220 Z250 S0                         ; set axis maxima
 
; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                            ; configure active-high endstop for low end on Z via pin zstop
 
; Z-Probe
M950 S0 C"exp.heater3"                         ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z2.5                            ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20                       ; define mesh grid
 
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; sensor 1
;M308 S1 P"spi.cs1" Y"rtd-max31865"             ; configure sensor 1 as thermocouple via CS pin spi.cs1
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S300                                   ; set temperature limit for heater 1 to 300C
 
; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                           ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1 T45                              ; set fan 2 value. Thermostatic control is turned on
 
; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C
 
; Custom settings are not defined
 
; Miscellaneous
M501                                           ; load saved parameters from non-volatile memory

[Veti]

@d0minik96 said in Artillery Genius Duet 2 Wifi Configuration:

Also Extruder temp is shown as 200 °C

are you sure the thermistor setting is correct?

why do you have this commented out?
M308 S1 P"spi.cs1" Y"rtd-max31865"

[d0minik96]

@Veti i set it upo wrong with the configurator. it should be thermistor 1 in merlin like the heatbed. heatbed sensor shows 20°C so it works. Not sure what i did wrong with the extruder thermistor

[Veti]

is it 200 or 2000 ?

[d0minik96]

@Veti 2000

[d0minik96]

So i just did some try and error. I have 2 Z motors. They worked against each other. Now it they work right.

y axis works fine. When i move X-axis z Axis moves aswell. I move the motors without homing atm.
I plugged all motors off and tried each motor alone with the y axis. they worked all great. not sure why they move together when i move z or y axis alone in the dashboard. U have any suggestions what i can check ?

[Veti]

2000 means open circuit.

so check the wiring.

measure the resistance with a multimeter

[d0minik96]

@Veti ok!

[d0minik96]

@Veti Both Thermistors work now! Thank you very much

U have any idea why both x and z axis move when i try to move one of them ?

[Veti]

i could be because of mesh compensation

how are you moving the axis?

[d0minik96]

@Veti I just do the M564 S0 H0 Command so i can move axis without homing
and than i just go to dashboard and click on the bottons to move the axis manual. I did not active do a mesh bed compensation, is there a way to check in config if there is any setting done ?

[Veti]

in what way is the z axis moving when you move the x

[Veti]

post your current config.g m122 and a picture of your wiring

[d0minik96]

@Veti The movement of second axis is not random, if i move pos the second axis does as well. when i move neg. it moves neg. aswell.

M112:
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SN-6J9D2-3SD6S-9VT7M
Used output buffers: 3 of 24 (18 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73284 of which 24 recycled
Never used RAM 15312, free system stack 189 words
Tasks: NETWORK(ready,160) HEAT(blocked,309) MAIN(running,450) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:06:15 ago, cause: power up
Last software reset at 2021-01-29 19:39, reason: User, GCodes spinning, available RAM 15276, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 21.1, current 28.5, max 29.1
Supply voltage: min 24.1, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-29 20:09:26
Cache data hit count 464421949
Slowest loop: 6.16ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.17ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21RC2
  WiFi MAC address 40:f5:20:1d:c0:8e
  WiFi Vcc 3.45, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 16912
  WiFi IP address 192.168.178.160
  WiFi signal strength -51dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

[Veti]

did you plug in x motor into the second z header by accident?

WiFi firmware version 1.21RC2

you did not update your wifi firmware

[d0minik96]

Could this be the problem ? When i click on Compensation and Callibration it says: Compensation in use: none.

Im 100% Sure i use the right motor in the right plugs. Tested the connection like an hour ago and tested every motor while i plugged off all others

[Phaedrux]

Upload this zip file to the system tab in DWC.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip

[d0minik96]

@Phaedrux I will test it after installation!

[Veti]

post your current config