Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware

Hélder Rocha · 30 Jan 2021, 17:52

@Phaedrux Tks.... at the momment im with other problem. Forgot to include in the new config file the access point and now, i cant get access to it!

Phaedrux · 30 Jan 2021, 17:59

If it was added once before the SSID should be saved on the wifi module itself and sending M552 S1 should enable the module and it will try to connect to the strongest SSID it knows about.

If it doesn't seem to be doing that you can try re-adding it. Same steps as initial connection.

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

Hélder Rocha · 30 Jan 2021, 18:04

@Phaedrux I think i messed this up... it steel giving me the message that the access point is working, and i can connect to it, but i dont know why, im not ablet to accesse the IP... "page not work"

Phaedrux · 30 Jan 2021, 18:13

Are you sure the IP address is the same?

If you send M552 the Duet will respond with what the current IP address is.

What is the exact error message?

Hélder Rocha · 30 Jan 2021, 18:16

@Phaedrux yap....is the same

Hélder Rocha · 30 Jan 2021, 18:16

Could be anything in the new config i uploaded?

Veti · 30 Jan 2021, 18:17

@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:

@Phaedrux yap....is the same

that is not the exact error message

Phaedrux · 30 Jan 2021, 18:18

Try clearing your browser cache.

And if that doesn't work, I would check the /www folder on the SD card and replace the files there with a fresh copy of DWC.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/DuetWebControl-SD.zip

Hélder Rocha · 30 Jan 2021, 18:32

at the momment on YAT, it is sayng that the wifi module is connected to my home network! Do you know ohow to disable it, and reeturn to Duet access point?

Veti · 30 Jan 2021, 18:34

Send M552 S2 to start up in access point mode (if it is already running in station mode then you need to send M552 S0 first).

Hélder Rocha · 30 Jan 2021, 18:40

@Veti keeps saying "Enable to connect after i digit the IP on adress bar. I can stablish the access point, but cant access the DWC.

Hélder Rocha · 30 Jan 2021, 18:42

The blue signal on the board is lit

Phaedrux · 30 Jan 2021, 18:42

Are you wanting to run in access point mode where you connect to the Duet directly with your PC/phone? Or normal mode where the Duet connects to your home wifi network?

@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:

I can stablish the access point, but cant access the DWC.

In access point mode you need to connect to the Duet SSID with your PC.

Hélder Rocha · 30 Jan 2021, 18:50

@Phaedrux yes i know. After i upload my new config, i stoped having accesse to my DWC pannel. Because of that, i used M587 to privid me a different door to the DWC. Now i have a mess in my hands!!! I still can create a wifi signal from the Duet, the access point, but i cant open the DWC pannel. Says "Enable to connect".

Phaedrux · 30 Jan 2021, 18:53

It would help to see exactly what gcodes you are sending and what the responses are.

I still don't know if you're trying to use access point mode or not.

Hélder Rocha · 30 Jan 2021, 18:55

@Phaedrux i send the M552 S2 and i recieve the message:

"ok<LF> wifi module is providing access point DuetCr10, IP address 192.168.1.1<LF>

Veti · 30 Jan 2021, 18:56

@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:

192.168.1.1

and you are connecting to the access point and goint to http://192.168.1.1 ?

Phaedrux · 30 Jan 2021, 18:56

To access that IP address you must connect your PC to the wifi network DuetCr10 first. You won't have internet access when connected to that access point.

Hélder Rocha · 30 Jan 2021, 18:57

@Phaedrux im confuse. How do i connect to DuetCr10?

Hélder Rocha · 30 Jan 2021, 18:58

Ah...ok...i know that