Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Hélder Rocha
    • Profile
    • Following 0
    • Followers 0
    • Topics 4
    • Posts 136
    • Best 2
    • Controversial 0
    • Groups 0

    Hélder Rocha

    @Hélder Rocha

    2
    Reputation
    1
    Profile views
    136
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Hélder Rocha Unfollow Follow

    Best posts made by Hélder Rocha

    • RE: Issues at the end of printing!

      Yes, i read about that in this forum but i couldnt find that kind of hidden code. I used the m83 and it worked fine. Tks a lot Phaedrux

      posted in General Discussion
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @fcwilt said in BLTouch Config.:

      most recent v2 firmware

      Well i have the V2 2.05.01 at the momment!

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha

    Latest posts made by Hélder Rocha

    • RE: BLTouch Config.

      @Veti yes... is with "."

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @Veti it was not workig correctly either with the old firmware. After update the firmware, i already tried with 1.60 and it stops at 0,40mm.... the question is: Dont matter the value i define in G31 "Z", the probe will allways stop at 0,40 mm plus 5mm(because G1 Z5 F100 ) above the bed. If i down the nozzle by 5mm, in the DWC will show the "Z" Value defined on G31, but when i go measure with the wedge feeler, it is 0,40mm above the bed. Allways!

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      ; homeall.g
      ; called to home all axes
      ;
      ; generated by RepRapFirmware Configuration Tool v3.2.2 on Sun Jan 31 2021 16:45:05 GMT+0000 (Hora padrão da Europa Ocidental)
      G91 ; relative positioning
      G1 H2 Z5 F6000 ; lift Z relative to current position
      G1 H1 X-305 Y-305 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
      G1 H2 X5 Y5 F6000 ; go back a few mm
      G1 H1 X-305 Y-305 F240 ; move slowly to X and Y axis endstops once more (second pass)
      G90 ; absolute positioning
      G1 X200 Y150 F6000 ; go to first bed probe point and home Z
      G30 ; home Z by probing the bed

      ; Uncomment the following lines to lift Z after probing
      ;G91 ; relative positioning
      ;G1 Z5 F100 ; lift Z relative to current position
      ;G90 ; absolute positioning

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @Veti can you tell me how to use the </>? I dont know how and i´ll like to do it correctly!

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      the config you see, i have "Z" value at "0", because i put it to "0" before a leave my printer last night. I intent to restart the configuration today.

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @Veti i have done it several times...i´ve defined Z to 0.23, the first value obtained with G30 S-1. After restart the duet, and do homing, the zozzle stoped 0,40 mm above the bed, but the Z value on the DWC is 0,23mm!
      After that, i encreased the Z value 10 by 10 to check if the nozzle wold get closer to the bed! But nothing, it stays at 0,40mm all the times.

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @Hélder-Rocha "G30 S-1"

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      @Veti Hi, thank you for the reply.
      In the first point you mention, how do i determine the beta value?

      In the second point, yes, i know. I have allready stablish "z" with the value the DWC determinate after G30 S-. In fact, i´ve give it different vlues, seen the first time, it stys 0,40 above the bed. I tried to low the nozzle a litle, increasing the "Z" value, but it stays allways at 0,40... regardless the value i have on "Z"!

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: BLTouch Config.

      Hi good people. My firmware is allready updated and working fine. Some others things ill have to do in the Macros i have but it stays for later. Now, about my Bltouch i have the follow problem. Independently off the value i put in G31, after the probe is done, the nozzle allways stays at 0,40 mm from the bed!!! I´ll show here my config file, for you ti check if is there anything missplaced.

      Sorry, dont know how to use </>!

      ; Configuration file for Duet WiFi (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.2.2 on Sun Jan 31 2021 16:45:04 GMT+0000 (Hora padrão da Europa Ocidental)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"DuetCR10" ; set printer name
      M918 P1 E4 F2000000 ; configure direct-connect display

      ; Network
      M551 P"Stacus631" ; set password
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S0 ; physical drive 0 goes backwards
      M569 P1 S0 ; physical drive 1 goes backwards
      M569 P2 S1 ; physical drive 2 goes forwards
      M569 P3 S1 ; physical drive 3 goes forwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z400.00 E422.7 ; set steps per mm
      M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z800 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X300 Y300 Z400 S0 ; set axis maxima

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 P500 X-40 Y-10 Z0 ; set Z probe trigger value, offset and trigger height
      M557 X15:250 Y15:250 S20 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4700 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 R0.457 C360.7 D3.84 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 150C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M143 H1 S290 ; set temperature limit for heater 1 to 290C

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
      M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      posted in Duet Hardware and wiring
      Hélder Rochaundefined
      Hélder Rocha
    • RE: Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware

      Most problems are solved, but now i have this on YAT:

      Warning: IP 192.168.1.2 requested file 'R/A3EKIDA4MTg1NDgxYm...' from HTTP server, possibly a virus attack

      posted in Firmware installation
      Hélder Rochaundefined
      Hélder Rocha