• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Artillery Genius Duet 2 Wifi Configuration

Scheduled Pinned Locked Moved
Using Duet Controllers
artillery genius conversation
6
55
3.5k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    d0minik96
    last edited by 29 Jan 2021, 19:14

    Could this be the problem ? When i click on Compensation and Callibration it says: Compensation in use: none.

    Im 100% Sure i use the right motor in the right plugs. Tested the connection like an hour ago and tested every motor while i plugged off all others

    1 Reply Last reply Reply Quote 0
    • undefined
      Phaedrux Moderator
      last edited by 29 Jan 2021, 19:16

      Upload this zip file to the system tab in DWC.

      https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip

      Z-Bot CoreXY Build | Thingiverse Profile

      undefined 2 Replies Last reply 29 Jan 2021, 19:18 Reply Quote 0
      • undefined
        d0minik96 @Phaedrux
        last edited by 29 Jan 2021, 19:18

        @Phaedrux I will test it after installation!

        1 Reply Last reply Reply Quote 0
        • undefined
          Veti
          last edited by 29 Jan 2021, 19:19

          post your current config

          undefined 1 Reply Last reply 29 Jan 2021, 19:24 Reply Quote 0
          • undefined
            d0minik96 @Phaedrux
            last edited by 29 Jan 2021, 19:22

            @Phaedrux Reply how long does the installation normally take ? Now i cant connect. Does it save my Networksettings normally ?

            undefined 1 Reply Last reply 29 Jan 2021, 19:27 Reply Quote 0
            • undefined
              d0minik96 @Veti
              last edited by 29 Jan 2021, 19:24

              @Veti The current config is the one i posted a bit upper in this thread. did not change anything since than and i cant connect to my board due to the update right now

              1 Reply Last reply Reply Quote 0
              • undefined
                Phaedrux Moderator @d0minik96
                last edited by 29 Jan 2021, 19:27

                @d0minik96 said in Artillery Genius Duet 2 Wifi Configuration:

                @Phaedrux Reply how long does the installation normally take ? Now i cant connect. Does it save my Networksettings normally ?

                WiFi firmware version 1.21RC2

                I wonder if your wifi firmware was so old that behaviour has changed.

                You may need to connect with USB terminal to see what is happening. Use M122 to check if the wifi firmware was updated to 1.25.

                Then use M552 S1 to see if it will enable and connect.
                Use M587 to see a list of currently saved SSIDs
                use M588 S"*" to clear all curently saved SSIDs
                and then use M587 S"networkname" P"password" to readd your SSID

                Z-Bot CoreXY Build | Thingiverse Profile

                undefined 1 Reply Last reply 29 Jan 2021, 21:19 Reply Quote 0
                • undefined
                  d0minik96 @Phaedrux
                  last edited by 29 Jan 2021, 21:19

                  @Phaedrux M552 say Wifi is being started. But nothing happens and i cant connect. i have to wait until tomrrow to get my laptop in order to look on the sd card. Can i rescue the system somehow ?

                  undefined 1 Reply Last reply 29 Jan 2021, 21:52 Reply Quote 0
                  • undefined
                    Phaedrux Moderator @d0minik96
                    last edited by 29 Jan 2021, 21:52

                    @d0minik96 said in Artillery Genius Duet 2 Wifi Configuration:

                    Can i rescue the system somehow ?

                    @Phaedrux said in Artillery Genius Duet 2 Wifi Configuration:

                    You may need to connect with USB terminal to see what is happening.
                    Use M122 to check if the wifi firmware was updated to 1.25.
                    Then use M552 S1 to see if it will enable and connect.
                    Use M587 to see a list of currently saved SSIDs
                    use M588 S"*" to clear all curently saved SSIDs
                    and then use M587 S"networkname" P"password" to readd your SSID

                    Z-Bot CoreXY Build | Thingiverse Profile

                    undefined 1 Reply Last reply 30 Jan 2021, 23:39 Reply Quote 0
                    • undefined
                      d0minik96 @Phaedrux
                      last edited by 30 Jan 2021, 23:39

                      @Phaedrux didnt work, guess i have to do a reset tomorrow

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        d0minik96
                        last edited by 12 Mar 2021, 16:37

                        So i finally updated the software. It still does not work.

                        I unplugged my Z and y Motor, so just my x Motor is plugged in.
                        When i manual move the x axis in the dashboard: x- Axis moves like it should.
                        When i manual move the z axis in the dashboard (attention!: z Motors are unplugged!!!) : x axis moves aswell. Whats strange is, that in this state the Motor moves kinda slower and there appeared popup that says: response takes 2 long. See console. Console: Warning: motor phase A may be disconnected reported by driver(s) 2
                        Warning: motor phase B may be disconnected reported by driver(s) 2
                        ( I think this comes because z Motors are unplugged and it tries to move z Axis aswell.)

                        If i unplugg my X Motor and only plugg in one z axis: Z axis moves when i move manual z or x axis.

                        i definitely did not mess up the wiring of the motors. So im sure this is a software issue.
                        But i must admit my Board is not a original one, so it might be a hardware issue aswell.
                        I will try to repeat the reprap config tool. maybe i messed up some settings there.... if somebody got a tipp for me what i can check i would be very pleased. My 3d Printer is laying arround on my workbench for a long time now and i finally want to print again :*(

                        undefined 1 Reply Last reply 12 Mar 2021, 17:05 Reply Quote 0
                        • undefined
                          engikeneer @d0minik96
                          last edited by 12 Mar 2021, 17:05

                          @d0minik96 Looking at your config.g posted above, line 10:

                          M669 K2                                        ; select CoreXY mode
                          

                          That command sets your printer in 'Core XZ' configuration (like core xy, but with x&z). That's why you're getting the weird movement.

                          I believe the artillery genius is a cartesian (like a prusa?) so you want:

                          M669 K0 ; set cartesian mode
                          

                          For ref: https://duet3d.dozuki.com/Wiki/Gcode#Section_M669_Set_kinematics_type_and_kinematics_parameters

                          E3D TC with D3Mini and Toolboards.
                          Home-built CoreXY, Duet Wifi, Chimera direct drive, 2x BMG, 300x300x300 build volume
                          i3 clone with a bunch of mods

                          undefined 2 Replies Last reply 12 Mar 2021, 17:16 Reply Quote 2
                          • undefined
                            d0minik96 @engikeneer
                            last edited by 12 Mar 2021, 17:16

                            @engikeneer said in Artillery Genius Duet 2 Wifi Configuration:

                            M669 K0

                            Oh man! That's it! It works finally!!!! Thank you so much. I really lost my hope with this conversation!

                            1 Reply Last reply Reply Quote 1
                            • undefined
                              d0minik96 @engikeneer
                              last edited by 12 Mar 2021, 17:22

                              @engikeneer still i wonder why core xz is wrong.

                              i have a Baseplate that moves in y direction . and my extruder is moving in xz direction. ? Can you explain me why kartesian is the setting to take ?

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                Phaedrux Moderator
                                last edited by 12 Mar 2021, 17:46

                                This is coreXZ. It's very different. It's basically a coreXY rotated 90 degrees on it's end.

                                https://reprap.org/forum/read.php?2,377858

                                @engikeneer Good eye!

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 1
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA