• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Ringing on prints

Scheduled Pinned Locked Moved
Tuning and tweaking
9
28
1.9k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    RAM @hackinistrator
    last edited by RAM 13 Feb 2021, 19:29

    @hackinistrator here is the S3D printer profile I have.
    S3D Hypercube Profile

    @pkos thanks for the suggestions. I cant work out what it is. I have checked the belt tensions and I am not using them reinforced white belts with metal strands as I had read that they give problems.

    I have even gone back over the mounting points to make sure that nothing had come loose and that the idler pulleys were all freely spinning to the point I even printed new idler pulley mounts and changed them over.

    only thing I haven't done yet on the calibration things that you mentioned is the pressure advance tuning and the calibration slat.

    I will try the calibration Slat but I am still trying to get my head around the pressure advance tuning thing before I even attempt it.

    1 Reply Last reply Reply Quote 0
    • undefined
      pkos
      last edited by 13 Feb 2021, 19:53

      Right, then first make sure you do the slat - that makes sure you are printing square.

      Then, do extruder calibration, extrusion calibration and only once you have that - then attempt PA 🙂 If you have a direct drive, PA won't help much.

      Voron 2.4 (Duet 3 6HC + 3HC standalone), Voron SW (Duet 3 mini 5+ standalone), Voron Trident (Duet 3 mini 5+ standalone), Voron 0.1

      1 Reply Last reply Reply Quote 0
      • undefined
        hackinistrator
        last edited by hackinistrator 13 Feb 2021, 20:05

        HyperCube-CoreXY.TXT

        I slightly changed your profile , can you test it ?
        (rename file to .fff instead of txt)
        please print the cylinders one at a time , not both at the same time .

        for some reason your speed is set very slow at 20mm/s , why ?
        i changed it to 45mm/s and reduced acceleration , if you have some kind of issues . if its a problem set speed back to 20mm/s
        other changes should not effect your printer . the profile seems very old.

        undefined 1 Reply Last reply 13 Feb 2021, 20:38 Reply Quote 1
        • undefined
          RAM @hackinistrator
          last edited by 13 Feb 2021, 20:38

          @hackinistrator Oh damn it exported the TPU testing profile I was setting up and not the PLA. Sorry that was my fault I didn't realise it had done that.

          If you would prefer to look at how the PLA profile is for the printer it is here.

          HyperCube-CoreXYPLA.txt

          what makes you say the profile is old ?

          1 Reply Last reply Reply Quote 0
          • undefined
            hackinistrator
            last edited by 13 Feb 2021, 21:25

            are you using the latest s3d version ? (they didnt update in years and probably dead , but still your profile config looks like it was created before the latest version)

            if you have time try my profile for single cylinder .

            undefined 1 Reply Last reply 13 Feb 2021, 21:56 Reply Quote 0
            • undefined
              RAM @hackinistrator
              last edited by 13 Feb 2021, 21:56

              @hackinistrator yep I am using v4.1.2 which is the latest. I am more than happy to try a different slicer even though I am not familiar with other slicers. I did used to use Cura years ago when I 1st got my Hictop in clone but ended switching over to Simplify3D as I found I was getting better prints using it.

              I am doing the 20mm cylinder now and I will do the 40mm after to see what the difference is. So far it is looking really good. Haven't a clue what you changed but it seems to be doing the trick so far. Fingers crossed and it will have solved the issue.

              undefined 1 Reply Last reply 14 Feb 2021, 08:15 Reply Quote 0
              • undefined
                RAM @RAM
                last edited by 14 Feb 2021, 08:15

                @hackinistrator whatever you changed seems to have worked wonders. I will delete the other profile and run with what you have done for me.
                20210214_081110.jpg

                Only thing that I would like to do is try and minimise the seam line a bit more but if that is all I have to contend with I will gladly put up with that.

                If you have any other suggestions to improve it further I would be very grateful.

                1 Reply Last reply Reply Quote 0
                • undefined
                  Blacksheep99
                  last edited by 14 Feb 2021, 08:28

                  Give Prusaslicer a go. I’ve moved to it from Cura and I’m impressed with it

                  1 Reply Last reply Reply Quote 1
                  • undefined
                    hackinistrator
                    last edited by 14 Feb 2021, 09:49

                    i set very conservative acceleration and jerk setting in the profile i sent you (i thought you are limited to 20mm/s from your original profile) . in S3d those values are under post processing script , as this 150$ software didn't add simple acceleration and jerk settings 😠

                    i also think you should move away from s3d as they are going nowhere it seems .
                    for easy transition you can try ideamaker .

                    as much as i hate S3D as a company , i still find it useful for multi process and sequential printing .other then that , prusaslicer , ideamaker and cura , all of them much better now .

                    undefined 1 Reply Last reply 14 Feb 2021, 10:33 Reply Quote 1
                    • undefined
                      RAM @hackinistrator
                      last edited by 14 Feb 2021, 10:33

                      @hackinistrator yea the original was a TPU profile I was setting up but I didn't realise I had exported that profile, I will use what you sent me as it is so much nicer and seems to have removed that pause as well at the end of each move.

                      I will have a go using your settings but upping the printing speed to 70mms and also try prusa slicer and see how I get on with it.

                      I know Simplify3D were meant to be releasing a v5 but I am not paying again to do the upgrade and by the looks of it, the Prusa Community for the Slicer is really powering the slicer forward.

                      1 Reply Last reply Reply Quote 0
                      28 out of 28
                      • First post
                        28/28
                        Last post
                      Unless otherwise noted, all forum content is licensed under CC-BY-SA