• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.

Scheduled Pinned Locked Moved
Firmware installation
4
20
809
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    alankilian
    last edited by 1 Feb 2021, 20:55

    First Probe file from the macros folder:

    M117 Begin RostockMAX Autolevel Calibration
    M117 Heating Bed Please Wait
    M190 S60
    M104 S0
    M140 S0
    M117 Heat Off - Starting Autolevel Keep Clear
    M558 P5 I0 A1 S0.05 R0.4 H20 F2500
    G32
    M500
    M117 Re-Heating for Bed Mapping Please Wait Keep Clear
    M558 P5 I0 A1 S0.05 R0.4 H20 F2500 
    M190 S60
    M140 S0
    M106 P0 S0
    G29
    M500
    G28
    M84
    M375
    M117 End RostockMAX Autolevel Calibration
    

    SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

    undefined 1 Reply Last reply 1 Feb 2021, 20:59 Reply Quote 0
    • undefined
      alankilian
      last edited by 1 Feb 2021, 20:57

      I've NEVER really gotten a satisfactory workflow for:

      • calibrating after moving the machine
      • calibrating once-per-power-on
      • calibrating once-per-print.

      SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

      undefined undefined 2 Replies Last reply 1 Feb 2021, 21:01 Reply Quote 0
      • undefined
        Phaedrux Moderator @alankilian
        last edited by 1 Feb 2021, 20:59

        @alankilian The problem with that macro is that it has M558 commands formatted for RRF2. So if you intend to use that macro you need to update those M558 lines or remove them entirely.

        Running that macro could be part of the problem actually if it's altering your expected M558 from config.g

        Z-Bot CoreXY Build | Thingiverse Profile

        undefined 1 Reply Last reply 1 Feb 2021, 21:11 Reply Quote 0
        • undefined
          Phaedrux Moderator @alankilian
          last edited by 1 Feb 2021, 21:01

          @alankilian said in Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.:

          I've NEVER really gotten a satisfactory workflow for:

          • calibrating after moving the machine
          • calibrating once-per-power-on
          • calibrating once-per-print.

          I'm not a delta user so I'm next to useless there. though from what I gather people tend to home to the top, do a single G30 at the center of the bed, and then do G32 for a 6 factor calibration and maybe a G29 for a heightmap if the bed isn't perfectly flat.

          Other than that I can only point you here:

          https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer
          https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareDeltaPrinter

          Z-Bot CoreXY Build | Thingiverse Profile

          undefined 1 Reply Last reply 1 Feb 2021, 21:11 Reply Quote 1
          • undefined
            alankilian @Phaedrux
            last edited by 1 Feb 2021, 21:11

            @Phaedrux said in Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.:

            or remove them entirely

            When I have time I should go through the SeeMeCNC SD card contents and update them for RRF3 and send them back.

            SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

            1 Reply Last reply Reply Quote 0
            • undefined
              alankilian @Phaedrux
              last edited by 1 Feb 2021, 21:11

              @Phaedrux said in Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.:

              https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer
              https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareDeltaPrinter

              Are those RRF 3 applicable?

              SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

              undefined undefined 2 Replies Last reply 1 Feb 2021, 21:12 Reply Quote 0
              • undefined
                Phaedrux Moderator @alankilian
                last edited by 1 Feb 2021, 21:12

                They are delta applicable. 🤷

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators @alankilian
                  last edited by 2 Feb 2021, 07:25

                  @alankilian said in Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.:

                  I've NEVER really gotten a satisfactory workflow for:

                  • calibrating after moving the machine
                  • calibrating once-per-power-on
                  • calibrating once-per-print.

                  The workflow that I use on my delta is:

                  • Press the button on PanelDue that runs the preheat macro. This heats the bed to 60C and the nozzle to 190C.
                  • When it is hot, press the auto calibration button. My bed.g file will home the printer first if necessary.
                  • Print

                  Between prints I usually run the sequence again, but if I have several small prints to do then I skip it.

                  Some users put the G32 command in the start.g file or the slicer start Gcode.

                  HTH David

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 1
                  • undefined
                    thekarlmiller @alankilian
                    last edited by 4 May 2021, 18:50

                    @alankilian - did you come up with a working set of duet2 files for use with the SE300 ?
                    SeeMeCNC is REFUSING to tell me what the specs are for the SE300 so I can setup the e0temp and e0heat.
                    I can't figure out what type of temperature sensor it has or its Beta value or the heater parameters either. Very frustrating considering I supported them when they started up, and just paid for the SE300 but the most they would tell me is "change the parameters in config.g".

                    undefined 1 Reply Last reply 4 May 2021, 19:50 Reply Quote 0
                    • undefined
                      alankilian @thekarlmiller
                      last edited by 4 May 2021, 19:50

                      @thekarlmiller I got a few answers from them:

                      From Steve:
                      M307 H0 B0                                ; Heated Bed (H2)
                      M305 P0 T100000 B4388 R4700 C7.06e-8 H30 L0        ; Bed thermistor
                      
                      M305 P1 T100000 B4388 R4700 H30 L0        ; Hot end Thermistor
                      M563 P0 D0 H1                              ; Hot end (T0), drive (E0), heater (H1)
                      G10 P0 S0 R0                              ; Hot end operating and standby temperatures
                      
                      Also from Steve:
                      B57560G104F EPCOS / TDK | Mouser 
                      https://www.mouser.com/ProductDetail/EPCOS-TDK/B57560G104F/?qs=%2Fha2pyFaduhYMyMmNPiRCZBlFExy0IoMv%2FYmPx9ox2iWGLyJQlg7Pg%3D%3D 
                      

                      Here's my config.g but I haven't really worried about the temps. I always end up adjusting up or down for a particular print, so I don't really care that it's super accurate.

                      ; Configuration file for Duet WiFi (firmware version 3)
                      ; executed by the firmware on start-up
                      ;
                      ; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue Mar 09 2021 13:21:24 GMT-0500 (Eastern Standard Time)
                      
                      ; General preferences
                      G90                                                     ; send absolute coordinates...
                      M83                                                     ; ...but relative extruder moves
                      M550 P"alan"                                            ; set printer name
                      M665 R132.5 L291.06 B132.5 H400                         ; Set delta radius, diagonal rod length, printable radius and homed height
                      M666 X0 Y0 Z0                                           ; put your endstop adjustments here, or let auto calibration find them
                      
                      ; Network
                      M552 P0.0.0.0 S1                                        ; enable network and acquire dynamic address via DHCP
                      M586 P0 S1                                              ; enable HTTP
                      M586 P1 S0                                              ; disable FTP
                      M586 P2 S0                                              ; disable Telnet
                      
                      ; Drives
                      M569 P0 S1                                              ; physical drive 0 goes forwards
                      M569 P1 S1                                              ; physical drive 1 goes forwards
                      M569 P2 S1                                              ; physical drive 2 goes forwards
                      M569 P3 S1                                              ; physical drive 3 goes forwards
                      
                      ; Testing external driver
                      ;M569 P5 S1 T4:4:4:4                                     ; physical drive 5 goes forwards
                      ;M584 X0 Y1 Z2 E3 U5                                     ; set drive mapping
                      ;M350 X16 Y16 Z16 E16 U16 I1                             ; configure microstepping with interpolation
                      ;M92 X100.00 Y100.00 Z100.00 U100.00 E91.00              ; set steps per mm
                      ;M566 X1200.00 Y1200.00 Z1200.00 U1200 E1200.00          ; set maximum instantaneous speed changes (mm/min)
                      ;M203 X18000.00 Y18000.00 Z18000.00 U18000E1200.00       ; set maximum speeds (mm/min)
                      ;M201 X1000.00 Y1000.00 Z1000.00 U1000E1000.00           ; set accelerations (mm/s^2)
                      ;M906 X1000 Y1000 Z1000 E800 U1000I30                    ; set motor currents (mA) and motor idle factor in per cent
                      
                      M584 X0 Y1 Z2 E3                                        ; set drive mapping
                      M350 X16 Y16 Z16 E16 I1                                 ; configure microstepping with interpolation
                      M92 X100.00 Y100.00 Z100.00 E91.00                      ; set steps per mm
                      M566 X1200.00 Y1200.00 Z1200.00 E1200.00                ; set maximum instantaneous speed changes (mm/min)
                      M203 X18000.00 Y18000.00 Z18000.00 E1200.00             ; set maximum speeds (mm/min)
                      M201 X1000.00 Y1000.00 Z1000.00 E1000.00                ; set accelerations (mm/s^2)
                      M906 X1000 Y1000 Z1000 E800 I30                         ; set motor currents (mA) and motor idle factor in per cent
                      
                      M84 S30                                                 ; Set idle timeout
                      
                      ; Axis Limits
                      M208 Z0 S1                                              ; set minimum Z
                      
                      ; Endstops
                      M574 X2 S1 P"xstop"                                     ; configure active-high endstop for high end on X via pin xstop
                      M574 Y2 S1 P"ystop"                                     ; configure active-high endstop for high end on Y via pin ystop
                      M574 Z2 S1 P"zstop"                                     ; configure active-high endstop for high end on Z via pin zstop
                      
                      ; Z-Probe
                      M558 P1 C"zprobe.in" H5 F60000 T6000                    ; set Z probe type to unmodulated and the dive height + speeds
                      G31 P500 X0 Y0 Z0.1                                     ; set Z probe trigger value, offset and trigger height
                      M557 R132 S20                                           ; define mesh grid
                      
                      ; Heaters
                      M308 S0 P"bedtemp" Y"thermistor" T100000 B4388 C7.06e-8 ; configure sensor 0 as thermistor on pin bedtemp
                      M950 H0 C"bedheat" T0                                   ; create bed heater output on bedheat and map it to sensor 0
                      M307 H0 B1 S1.00                                        ; enable bang-bang mode for the bed heater and set PWM limit
                      M140 H0                                                 ; map heated bed to heater 0
                      M143 H0 S120                                            ; set temperature limit for heater 0 to 120C
                      M308 S1 P"e0temp" Y"thermistor" T100000 B4385           ; configure sensor 1 as thermistor on pin e0temp
                      M950 H1 C"e0heat" T1                                    ; create nozzle heater output on e0heat and map it to sensor 1
                      M307 H1 B0 S1.00                                        ; disable bang-bang mode for heater  and set PWM limit
                      M143 H1 S280                                            ; set temperature limit for heater 1 to 280C
                      
                      ; Fans
                      M950 F0 C"fan0" Q500                                    ; create fan 0 on pin fan0 and set its frequency
                      M106 P0 S0 H-1                                          ; set fan 0 value. Thermostatic control is turned off
                      M950 F1 C"fan1" Q500                                    ; create fan 1 on pin fan1 and set its frequency
                      M106 P1 S1 H1 T45                                       ; set fan 1 value. Thermostatic control is turned on
                      
                      ; Tools
                      M563 P0 D0 H1 F0                                        ; define tool 0
                      G10 P0 X0 Y0 Z0                                         ; set tool 0 axis offsets
                      G10 P0 R0 S0                                            ; set initial tool 0 active and standby temperatures to 0C
                      
                      ; Custom settings
                      M501                                                    ; Load config-overrides.g
                      T0                                                      ; Select tool zero
                      
                      ; Miscellaneous
                      M575 P1 S1 B57600                                       ; enable support for PanelDue
                      

                      And, after tuning, my config-override.g:

                      ; config-override.g file generated in response to M500 at 2021-02-19 14:01
                      ; This is a system-generated file - do not edit
                      ; Delta parameters
                      M665 L291.060:291.060:291.060 R143.801 H400.348 B132.5 X0.025 Y-0.081 Z0.000
                      M666 X-0.047 Y-0.016 Z0.062 A0.00 B0.00
                      ; Heater model parameters
                      M307 H0 R0.105 C920.580:920.580 D9.08 S1.00 V13.0 B0
                      M307 H1 R3.939 C97.142:97.142 D5.78 S1.00 V13.0 B0
                      ; Workplace coordinates
                      G10 L2 P1 X0.00 Y0.00 Z0.00
                      G10 L2 P2 X0.00 Y0.00 Z0.00
                      G10 L2 P3 X0.00 Y0.00 Z0.00
                      G10 L2 P4 X0.00 Y0.00 Z0.00
                      G10 L2 P5 X0.00 Y0.00 Z0.00
                      G10 L2 P6 X0.00 Y0.00 Z0.00
                      G10 L2 P7 X0.00 Y0.00 Z0.00
                      G10 L2 P8 X0.00 Y0.00 Z0.00
                      G10 L2 P9 X0.00 Y0.00 Z0.00
                      M486 S-1
                      

                      I don't think my mech bed heigh compensation works well at all, I just move the part around on the bed until it's OK, and use baby-stepping until I get up to about 0.55mm every time I start.

                      I had it working much better with RRF 2.05, but I jumped in to RRF 3 and haven't spent the time to figure out how to get things working again.

                      I just have too many "real" things to print to worry about it.

                      SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                      undefined 1 Reply Last reply 6 May 2021, 19:53 Reply Quote 1
                      • undefined
                        thekarlmiller @alankilian
                        last edited by 6 May 2021, 19:53

                        @alankilian said in Duet2/Ethernet Update from 2.05 to 3.2 went perfectly.:

                        B57560G104F

                        Thank you very much @alankilian . This is a huge help.
                        Your answer actually highlights one of my difficulties...
                        The NTC thermistor you provided has Beta values indicated on its product page of (4066 K, 4036 K, 4085 K), and the datasheet has them as (4072, 4036, 4092) and the product page values aren't even represented in the datasheet.
                        M308 commands in your config.g set the thermistor Beta value as 4385. I am not saying that it isn't correct, but I don't yet know how to determine how to setup these thermistors for the Duet firmware. BTW - I am currently using v3.2.2.
                        The other value I don't get is the T100000 - shouldn't that be T104000?
                        How did you determine the C value for the bed thermistor?
                        Thank you again, Karl

                        undefined 1 Reply Last reply 6 May 2021, 20:05 Reply Quote 0
                        • undefined
                          alankilian @thekarlmiller
                          last edited by alankilian 5 Jun 2021, 20:06 6 May 2021, 20:05

                          @thekarlmiller I got the bed from Steve at SeeMeCNC:

                          From Steve:
                          M307 H0 B0                                    ; Heated Bed (H2)
                          M305 P0 T100000 B4388 R4700 C7.06e-8 H30 L0   ; Bed thermistor
                          

                          T100000 is right because these thermisters have a reistance of 100,000 Ohms at 25 degrees C.

                          But like I said I haven't checked at ALL to see if these are right.

                          I just fire it up and print.
                          And then adjust the temps until the parts come out right.

                          SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA