Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Thermistor,PT100, PT1000

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    21
    1.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Auréundefined
      Auré
      last edited by Auré

      Hello, so I have this on my config.g but the toolboard don't see the thermistor 😕

      M308 S1 P"121.temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin 121.temp0
      M950 H1 C"121.out0" T1 ; create nozzle heater output on 121.out0 and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M143 H1 S280 ; set temperature limit for heater 1 to 280C

      I have chek the thermistor with a multimeter and it's ok

      Reprap core XY, Ender 3 upgraded.

      If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
      A quote from Jacques Rouxel

      1 Reply Last reply Reply Quote 0
      • Auréundefined
        Auré
        last edited by

        I found this

        I change a command line with:

        M308 S1 P"121.temp0" Y"thermistor" T100000 B4725 C7.06e-8

        But don't work

        Reprap core XY, Ender 3 upgraded.

        If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
        A quote from Jacques Rouxel

        1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          Can you send M115 and M115 B121 and confirm that the firmware version on both the mainboard and toolboard match?

          Z-Bot CoreXY Build | Thingiverse Profile

          Auréundefined 1 Reply Last reply Reply Quote 0
          • Auréundefined
            Auré @Phaedrux
            last edited by

            @phaedrux said in Thermistor,PT100, PT1000:

            M115 B121

            Yep:

            m115.jpg

            Console:

            m115 console.jpg

            M115 B121:

            m115 b121.jpg

            Reprap core XY, Ender 3 upgraded.

            If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
            A quote from Jacques Rouxel

            jay_s_ukundefined 1 Reply Last reply Reply Quote 0
            • jay_s_ukundefined
              jay_s_uk @Auré
              last edited by

              @auré you're running out of sync firmware. Try running M997 B121

              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

              Auréundefined 1 Reply Last reply Reply Quote 0
              • Auréundefined
                Auré @jay_s_uk
                last edited by Auré

                @jay_s_uk said in Thermistor,PT100, PT1000:

                M997 B121

                Ok I send M997 B121:

                update tool.jpg

                The thermistore not work

                I would like stop the fan and I have new error:

                fan.jpg

                Reprap core XY, Ender 3 upgraded.

                If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
                A quote from Jacques Rouxel

                1 Reply Last reply Reply Quote 0
                • Auréundefined
                  Auré
                  last edited by Auré

                  For the fan I found this post

                  I add F1:

                  M563 P0 D0 H1 F0 F1 ; define tool 0

                  And now the fan control work.

                  But not the thermistor.

                  I don't know why but now the thermistor on the toolboard work.....

                  I have only add F1

                  Reprap core XY, Ender 3 upgraded.

                  If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
                  A quote from Jacques Rouxel

                  jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                  • jay_s_ukundefined
                    jay_s_uk @Auré
                    last edited by

                    @auré post your full config and send M115 B121 to confirm 3.2.2 is on the toolboard

                    Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                    Phaedruxundefined 1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator @jay_s_uk
                      last edited by

                      @jay_s_uk said in Thermistor,PT100, PT1000:

                      send M115 B121 to confirm 3.2.2 is on the toolboard

                      Looks like he is now.

                      Full config.g would be nice.

                      Z-Bot CoreXY Build | Thingiverse Profile

                      1 Reply Last reply Reply Quote 0
                      • Auréundefined
                        Auré
                        last edited by

                        I post tomorrow the config.g thank you for your help good night 🙂

                        Reprap core XY, Ender 3 upgraded.

                        If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
                        A quote from Jacques Rouxel

                        1 Reply Last reply Reply Quote 0
                        • Auréundefined
                          Auré
                          last edited by

                          Hello,

                          ; Configuration file for Duet 3 (firmware version 3)
                          ; executed by the firmware on start-up
                          ;
                          ; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Jun 04 2021 20:14:20 GMT+0200 (heure d’été d’Europe centrale)

                          ; General preferences
                          G90 ; send absolute coordinates...
                          M83 ; ...but relative extruder moves
                          M550 P"Duet 3" ; set printer name
                          M552 S1
                          M669 K1 ; select CoreXY mode

                          ; Drives
                          G4 S1 ;wait for expansion boards to start
                          M569 P0.0 S0 ; physical drive 0.0 goes forwards
                          M569 P0.1 S0 ; physical drive 0.1 goes forwards
                          M569 P0.3 S0 ; physical drive 0.3 goes forwards
                          M569 P0.4 S0 ; physical drive 0.4 goes forwards
                          M569 P0.5 S0 ; physical drive 0.5 goes forwards
                          M569 P121.0 S1 ; physical drive 121.0 goes forwards
                          M584 X0.0 Y0.1 Z0.3:0.4:0.5 E121.0 ; set drive mapping
                          M671 X-30,109:171.1:372.309 Y-10,413:367,797:-10,413 S50
                          M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                          M92 X160.00 Y160.00 Z800.00 E335.40 ; set steps per mm
                          M566 X1200.00 Y1200.00 Z30.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                          M203 X18000.00 Y18000.00 Z1800.00 E1200.00 ; set maximum speeds (mm/min)
                          M201 X1600.00 Y1600.00 Z100.00 E250.00 ; set accelerations (mm/s^2)
                          M906 X1000 Y1000 Z1200 E840 I30 ; set motor currents (mA) and motor idle factor in per cent
                          M84 S30 ; Set idle timeout

                          ; Axis Limits
                          M208 X0 Y0 Z0 S1 ; set axis minima
                          M208 X365 Y365 Z335 S0 ; set axis maxima

                          ; Endstops
                          M574 X1 S1 P"121.io1.in" ; configure active-high endstop for low end on X via pin 121.io1.in
                          M574 Y1 S1 P"io0.in" ; configure active-high endstop for low end on Y via pin io0.in
                          M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                          ; Z-Probe
                          M950 S0 C"121.io0.out" ; create servo pin 0 for BLTouch
                          M558 P9 C"^121.io0.in" H15 F120 T9000 ; set Z probe type to bltouch and the dive height + speeds
                          G31 P500 X3 Y-41 Z2.5 ; set Z probe trigger value, offset and trigger height
                          M557 X15:215 Y15:195 S20 ; define mesh grid

                          ; Heaters
                          M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
                          M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                          M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                          M140 H0 ; map heated bed to heater 0
                          M143 H0 S100 ; set temperature limit for heater 0 to 100C
                          M308 S1 P"121.temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin 121.temp0
                          M950 H1 C"121.out0" T1 ; create nozzle heater output on 121.out0 and map it to sensor 1
                          M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                          M143 H1 S280 ; set temperature limit for heater 1 to 280C

                          ; Fans
                          M950 F0 C"121.out1" Q500 ; create fan 0 on pin 121.out1 and set its frequency
                          M106 P0 S0 H T45 ; set fan 0 value. Thermostatic control is turned on
                          M950 F1 C"121.out2" Q500 ; create fan 1 on pin 121.out2 and set its frequency
                          M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

                          ; Tools
                          M563 P0 D0 H1 F0 F1 ; define tool 0
                          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                          ; Custom settings are not defined

                          ; Miscellaneous
                          M501 ; load saved parameters from non-volatile memory
                          M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

                          Reprap core XY, Ender 3 upgraded.

                          If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
                          A quote from Jacques Rouxel

                          jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                          • jay_s_ukundefined
                            jay_s_uk @Auré
                            last edited by

                            @auré said in Thermistor,PT100, PT1000:

                            ; Drives
                            G4 S1 ;wait for expansion boards to start

                            can you try increasing the G4 S1 to G4 S4 to give it a bit longer for the toolboard to be ready?

                            Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                            Auréundefined 1 Reply Last reply Reply Quote 0
                            • Auréundefined
                              Auré @jay_s_uk
                              last edited by

                              @jay_s_uk said in Thermistor,PT100, PT1000:

                              can you try increasing the G4 S1 to G4 S4 to give it a bit longer for the toolboard to be ready?

                              Yes thank you, I told myself that I had to extend the time because when I start the printer with DWC open, sometimes I have error communication of bus, but I forgot.
                              I think you're right 4 second it's ok.

                              Reprap core XY, Ender 3 upgraded.

                              If you keep trying, you'll eventually succeed. So: the more you fail, the more likely you are to succeed.
                              A quote from Jacques Rouxel

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA