Config for the Pinda v2 ,need help!

; PINDA2
;
M558 P5 C"zprobe.in" H1.5 F1000 T12000 A3 ; set Z probe to PINDA2
M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950 ; temperature of PINDA2

T3P3Tony · 12 Oct 2021, 08:10

@lui2004 that looks correct and the config matches the wiring. As always when you test the trigger for the first time first confirm not is triggering as expected by manually lowering the Z axis so it's not the expected trigger height and checking the z probe is shown as switching in DWC

lui2004 · 12 Oct 2021, 10:12

@t3p3tony

after i do a Dynamic test

the pinda v2 wont stop it will crash into the bed

T3P3Tony · 12 Oct 2021, 10:25

@lui2004 if you move the probe down manually do you see the Zprobe indication on DWC change. What is it showing?

lui2004 · 12 Oct 2021, 11:31

@t3p3tony

the pinda wont trigger because i have a pei surface.

i have insert some Aluminum foil under the pei i now it will work.

which surface is good without Aluminum foil under pei ?

T3P3Tony · 12 Oct 2021, 11:36

@lui2004 whats the PEI surface mounted on? I suppose most people using PINDA style probes an aluminium bed.

lui2004 · 10 Dec 2021, 13:01

@t3p3tony

aluminium bed with pei

this is my heightmap:

 RepRapFirmware height map file v2 generated at 2021-10-12 14:59, min error -0.093, max error 0.125, mean 0.003, deviation 0.049
axis0,axis1,min0,max0,min1,max1,radius,spacing0,spacing1,num0,num1
X,Y,10.00,220.00,10.00,220.00,-1.00,20.00,20.00,11,11
      0,      0,      0,      0,      0,      0,      0,      0,      0,      0,      0
      0,      0,      0,  0.008, -0.000,  0.091,  0.057, -0.005,  0.050,  0.050,  0.007
      0,      0,      0, -0.000, -0.025,  0.082,  0.087,  0.050,  0.032,  0.091, -0.009
      0,      0,      0, -0.018,  0.025,  0.116,  0.125,  0.012,  0.007,  0.082, -0.025
      0,      0,      0, -0.025,  0.016,  0.116,  0.125, -0.018,  0.032, -0.005, -0.050
      0,      0,      0, -0.043, -0.025,  0.041,  0.025, -0.009, -0.018,  0.025, -0.084
      0,      0,      0, -0.050, -0.075, -0.034, -0.018, -0.000, -0.000, -0.000, -0.059
      0,      0,      0, -0.050, -0.038, -0.034, -0.021, -0.018, -0.018,  0.037, -0.059
      0,      0,      0, -0.055, -0.050, -0.043,  0.025, -0.018, -0.034, -0.055, -0.093
      0,      0,      0, -0.063, -0.034,  0.032,  0.025,  0.016, -0.009,  0.020, -0.050
      0,      0,      0, -0.030, -0.025,  0.007, -0.000,  0.025,  0.025,  0.050,  0.041

lui2004 · 13 Oct 2021, 19:16

I bought a new surface !

what is important to calibrate the pinda V2 ?

lui2004 · 14 Oct 2021, 03:00

This is my actuall config.g

 ; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
 
; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves
 
; Network
M550 P"Ender 5"                          ; Set machine name
M552 S1                                  ; Enable network
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet
 
; Drives
M569 P0 S1                               ; Physical drive 0 goes forwards
M569 P1 S1                               ; Physical drive 1 goes forwards
M569 P2 S0                               ; Physical drive 2 goes backwards
M569 P3 S1                              ; Physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1							; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E288.30                     ; set steps per mm
M566 X600.00 Y600.00 Z60.00 E300.00                  ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z600.00 E6000.00              ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1400 I30                         ; set motor currents (mA) and motor idle factor in per cent
M84 S30       
 
 
; Axis Limits
M208 X0 Y0 Z0 S1                                     ; set axis minima
M208 X235 Y235 Z250 S0                               ; set axis maxima
 
; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 									   ; configure Z-probe endstop for low end on Z
 
;Filament Sensors
M591 D0 P2 C"!e0_stop" S1   			   ;Extruder 1(0)
 
 
 
; PINDA2
;M558 P5 C"^zprobe.in" H1.5 F1000 T12000 A3 ; set Z probe to PINDA2
M558 K0 P8 C"^zprobe.in" I1 H2 F1000 T6000 A20 S0.005 ; set Z probe type to effector and the dive height + speeds, max number of probes per point, tolerance(MM)
M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950 ; temperature of PINDA2
G31 P500 X52.7 Y18 Z1.775                  ; set Z probe trigger value, offset and trigger height
M557 X10:210 Y10:210 S20                       ; define mesh grid
;M557 X41.2:219 Y15:195 S20
;M671 X28.8:198.8:198:28.8 Y24:24:194:194 P0.5
M557 X10:220 Y10:220 S20
 
 
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 								   ; set temperature limit for heater 1 to 300C
M307 H1 B0 S1.00           
 
; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on
 
; Tools
M563 P0 D0 H1                            ; Define tool 0 S3D
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C
 
; Automatic saving after power loss is not enabled
 
; Custom settings are not configured
M575 P1 S1 B57600 ; enable support for PanelDue
M572 D0 S0.05 ; Pressure Advance PLA
;M572 D0 S0.08 ; Pressure Advance PLA
M207 S1.50 R0 F2100 T2100 Z0 ; Firmware Retraction P0 S0.45 R0 F2100 T2100 Z0 ; Firmware Retraction
M204 P500 T2000
T0 ; Sets Tool0 as default
 
M501

homeall.g

 ; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:12 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head 4mm
G1 H1 X-240 Y-240 F3000 ; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600; move slowly 6mm in +X and +Y directions
G1 H1 X-10 Y-10 ; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 ; back to absolute mode
G1 X57.3 Y92 F2000 ; put head over the centre of the bed, or wherever you want to probe
G30 ; lower head, stop when probe triggered and set Z to trigger height

; homex.g

 ; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
G1 H1 X-240 F3000 ; move up to 240mm in the +X direction, stopping if the homing switch is triggered
G1 X-4 F600 ; move slowly 4mm in the -X direction
G1 H1 X10 ; move slowly 10mm in the +X direction, stopping at the homing switch
G1 H2 Z-4 F200 ; lower the head again
G90 ; back to absolute mode

homey.g

 ; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
G1 H1 Y-240 F3000 ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 X4 F600 ; move slowly 4mm in the +X direction
G1 H1 X-10 ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 H2 Z-4 F200 ; lower the head again
G90 ; back to absolute mode

homez.g

 ; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:37 GMT+0200 (Mitteleuropäische Sommerzeit)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G90               ; absolute positioning
G1 X57.3 Y92 F6000 ; go to first probe point
G30               ; home Z by probing the bed

thanks for help

lui2004 · 14 Oct 2021, 09:23

Hi

Is there a how to ,to set z offset on different temperature? Like in marlin?

	RepRapFirmware height map file v2 generated at 2021-10-12 14:59, min error -0.093, max error 0.125, mean 0.003, deviation 0.049
	axis0,axis1,min0,max0,min1,max1,radius,spacing0,spacing1,num0,num1
	X,Y,10.00,220.00,10.00,220.00,-1.00,20.00,20.00,11,11
	0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
	0, 0, 0, 0.008, -0.000, 0.091, 0.057, -0.005, 0.050, 0.050, 0.007
	0, 0, 0, -0.000, -0.025, 0.082, 0.087, 0.050, 0.032, 0.091, -0.009
	0, 0, 0, -0.018, 0.025, 0.116, 0.125, 0.012, 0.007, 0.082, -0.025
	0, 0, 0, -0.025, 0.016, 0.116, 0.125, -0.018, 0.032, -0.005, -0.050
	0, 0, 0, -0.043, -0.025, 0.041, 0.025, -0.009, -0.018, 0.025, -0.084
	0, 0, 0, -0.050, -0.075, -0.034, -0.018, -0.000, -0.000, -0.000, -0.059
	0, 0, 0, -0.050, -0.038, -0.034, -0.021, -0.018, -0.018, 0.037, -0.059
	0, 0, 0, -0.055, -0.050, -0.043, 0.025, -0.018, -0.034, -0.055, -0.093
	0, 0, 0, -0.063, -0.034, 0.032, 0.025, 0.016, -0.009, 0.020, -0.050
	0, 0, 0, -0.030, -0.025, 0.007, -0.000, 0.025, 0.025, 0.050, 0.041

	; Configuration file for Duet WiFi (firmware version 1.21)
	; executed by the firmware on start-up
	;
	; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)

	; General preferences
	G90 ; Send absolute coordinates...
	M83 ; ...but relative extruder moves

	; Network
	M550 P"Ender 5" ; Set machine name
	M552 S1 ; Enable network
	M586 P0 S1 ; Enable HTTP
	M586 P1 S0 ; Disable FTP
	M586 P2 S0 ; Disable Telnet

	; Drives
	M569 P0 S1 ; Physical drive 0 goes forwards
	M569 P1 S1 ; Physical drive 1 goes forwards
	M569 P2 S0 ; Physical drive 2 goes backwards
	M569 P3 S1 ; Physical drive 3 goes forwards
	M584 X0 Y1 Z2 E3 ; set drive mapping
	M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
	M92 X80.00 Y80.00 Z400.00 E288.30 ; set steps per mm
	M566 X600.00 Y600.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
	M203 X9000.00 Y9000.00 Z600.00 E6000.00 ; set maximum speeds (mm/min)
	M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
	M906 X800 Y800 Z800 E1400 I30 ; set motor currents (mA) and motor idle factor in per cent
	M84 S30


	; Axis Limits
	M208 X0 Y0 Z0 S1 ; set axis minima
	M208 X235 Y235 Z250 S0 ; set axis maxima

	; Endstops
	M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
	M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
	M574 Z1 S2 ; configure Z-probe endstop for low end on Z

	;Filament Sensors
	M591 D0 P2 C"!e0_stop" S1 ;Extruder 1(0)



	; PINDA2
	;M558 P5 C"^zprobe.in" H1.5 F1000 T12000 A3 ; set Z probe to PINDA2
	M558 K0 P8 C"^zprobe.in" I1 H2 F1000 T6000 A20 S0.005 ; set Z probe type to effector and the dive height + speeds, max number of probes per point, tolerance(MM)
	M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950 ; temperature of PINDA2
	G31 P500 X52.7 Y18 Z1.775 ; set Z probe trigger value, offset and trigger height
	M557 X10:210 Y10:210 S20 ; define mesh grid
	;M557 X41.2:219 Y15:195 S20
	;M671 X28.8:198.8:198:28.8 Y24:24:194:194 P0.5
	M557 X10:220 Y10:220 S20


	; Heaters
	M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
	M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
	M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
	M140 H0 ; map heated bed to heater 0
	M143 H0 S120 ; set temperature limit for heater 0 to 120C
	M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8; configure sensor 1 as thermistor on pin e0temp
	M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
	M143 H1 S280 ; set temperature limit for heater 1 to 300C
	M307 H1 B0 S1.00

	; Fans
	M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
	M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
	M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
	M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

	; Tools
	M563 P0 D0 H1 ; Define tool 0 S3D
	G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
	G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

	; Automatic saving after power loss is not enabled

	; Custom settings are not configured
	M575 P1 S1 B57600 ; enable support for PanelDue
	M572 D0 S0.05 ; Pressure Advance PLA
	;M572 D0 S0.08 ; Pressure Advance PLA
	M207 S1.50 R0 F2100 T2100 Z0 ; Firmware Retraction P0 S0.45 R0 F2100 T2100 Z0 ; Firmware Retraction
	M204 P500 T2000
	T0 ; Sets Tool0 as default

	M501

	; homeall.g
	; called to home all axes
	;
	; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:12 GMT+0200 (Mitteleuropäische Sommerzeit)
	G91 ; relative mode
	G1 H2 Z4 F200 ; raise head 4mm
	G1 H1 X-240 Y-240 F3000 ; move up to 240mm in the -X and -Y directions until the homing switches are triggered
	G1 H2 X4 Y4 F600; move slowly 6mm in +X and +Y directions
	G1 H1 X-10 Y-10 ; move up to 10mm in the -X and -Y directions until the homing switches are triggered
	G90 ; back to absolute mode
	G1 X57.3 Y92 F2000 ; put head over the centre of the bed, or wherever you want to probe
	G30 ; lower head, stop when probe triggered and set Z to trigger height

	; homex.g
	; called to home the X axis
	;
	; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
	G91 ; relative mode
	G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
	G1 H1 X-240 F3000 ; move up to 240mm in the +X direction, stopping if the homing switch is triggered
	G1 X-4 F600 ; move slowly 4mm in the -X direction
	G1 H1 X10 ; move slowly 10mm in the +X direction, stopping at the homing switch
	G1 H2 Z-4 F200 ; lower the head again
	G90 ; back to absolute mode

	; homey.g
	; called to home the Y axis
	;
	; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
	G91 ; relative mode
	G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
	G1 H1 Y-240 F3000 ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
	G1 X4 F600 ; move slowly 4mm in the +X direction
	G1 H1 X-10 ; move slowly 10mm in the -X direction, stopping at the homing switch
	G1 H2 Z-4 F200 ; lower the head again
	G90 ; back to absolute mode

	; homez.g
	; called to home the Z axis
	;
	; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:37 GMT+0200 (Mitteleuropäische Sommerzeit)
	G91 ; relative positioning
	G1 H2 Z5 F6000 ; lift Z relative to current position
	G90 ; absolute positioning
	G1 X57.3 Y92 F6000 ; go to first probe point
	G30 ; home Z by probing the bed