• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Rotating Magnetic Sensor - Keeps Pausing Printer

Scheduled Pinned Locked Moved Solved
Filament Monitor
9
151
9.5k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    wouldstain @T3P3Tony
    last edited by 3 Nov 2021, 18:18

    @t3p3tony

    about to run test @250C. Will post console output (assuming it pauses)

    config.g attached. modified slightly from previous to account for addition of garolite sheet on build plate.

    WS_110321_config.g

    1 Reply Last reply Reply Quote 0
    • undefined
      T3P3Tony administrators @wouldstain
      last edited by 3 Nov 2021, 18:46

      @wouldstain said in Rotating Magnetic Sensor - Keeps Pausing Printer:

      I can certainly dial it down if you think it would make a difference.

      no i don't - that was just an question seeing it at 235.

      www.duet3d.com

      undefined 1 Reply Last reply 3 Nov 2021, 18:48 Reply Quote 0
      • undefined
        wouldstain @T3P3Tony
        last edited by 3 Nov 2021, 18:48

        @t3p3tony gotcha.
        Just ran it at 250C. got this at less than 6%:

        Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 130 agc 75, measured sensitivity 26.29mm/rev, min 1% max 107% over 136.1mm

        same cube.

        undefined 1 Reply Last reply 3 Nov 2021, 18:55 Reply Quote 0
        • undefined
          T3P3Tony administrators @wouldstain
          last edited by 3 Nov 2021, 18:55

          @wouldstain I printed that on the test rig:
          5ed4bee5-8bcc-4ab8-b129-6ee48d774e88-image.png

          That was before I got your config so i need to change to your config.

          Can you try printing one of the drywall anchors in PLA with the PLA settings to see if you get the same issue (trying to see if its related to the PA/retract settings which are different). Also a short print to recreate the issue would be good.

          www.duet3d.com

          undefined undefined 3 Replies Last reply 3 Nov 2021, 18:56 Reply Quote 0
          • undefined
            T3P3Tony administrators @T3P3Tony
            last edited by 3 Nov 2021, 18:56

            I also need to switch the test rig back to Duet 2 from Duet 3 mini.

            www.duet3d.com

            1 Reply Last reply Reply Quote 0
            • undefined
              wouldstain @T3P3Tony
              last edited by wouldstain 11 Mar 2021, 20:01 3 Nov 2021, 19:57

              @t3p3tony

              Drywall anchor @ 250C:

              Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 130 agc 75, measured sensitivity 219.24mm/rev, min 6% max 128% over 19.5mm

              only got about 2% into it before stopping.

              PLA_250C_Drywall_Anchor.gcode

              FYI also have PETG printing at -.15 offset via babysteps so I did reset it for PLA.

              undefined 1 Reply Last reply 3 Nov 2021, 20:09 Reply Quote 0
              • undefined
                alankilian @wouldstain
                last edited by 3 Nov 2021, 20:09

                @wouldstain

                My printer has (0,0) in the center.
                Is there an easy way for me to provide an offset so I can try printing your .gcode?

                Or can you slice it centered on (0,0) for me to test with?

                SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                undefined undefined 2 Replies Last reply 3 Nov 2021, 20:35 Reply Quote 0
                • undefined
                  wouldstain @alankilian
                  last edited by 3 Nov 2021, 20:35

                  @alankilian
                  Not sure how that would be possible as slicer is set up for my railcore rig.
                  Center is somewhere around 150,150.

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    wouldstain @T3P3Tony
                    last edited by 3 Nov 2021, 21:04

                    @t3p3tony Ran another print at 195C just to test.
                    got about 60% through it then stopped:

                    m591 d0
                    Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 130 agc 75, measured sensitivity 28.51mm/rev, min -25% max 130% over 132.7mm

                    undefined 2 Replies Last reply 3 Nov 2021, 21:37 Reply Quote 0
                    • undefined
                      T3P3Tony administrators @alankilian
                      last edited by 3 Nov 2021, 21:30

                      @alankilian

                      @dc42 used this to offset the prints so they can br printed with e bed centered on 0,0

                      ; Remove the following line if your bed isn't centred on X0 Y0
                      G10 L2 P1 X-150 Y-150

                      offsets the coordinate system by 150mm in both X and Y.

                      Use with caution!

                      www.duet3d.com

                      undefined 1 Reply Last reply 3 Nov 2021, 23:44 Reply Quote 0
                      • undefined
                        T3P3Tony administrators @wouldstain
                        last edited by 3 Nov 2021, 21:37

                        @wouldstain thanks for the reports.

                        Can you confirm the changes between PETG and PLA in your setup:

                        1. Print temperature (don't think this matters as long as prints are working)
                        2. Print Speed?
                        3. Retraction distance (looks like 2mm in both files)?
                        4. PA setting? (looks like PLA = M572 D0 S0.06, PETG = M572 D0 S0.07?)
                        5. Anything else?

                        Cheers

                        www.duet3d.com

                        undefined 1 Reply Last reply 4 Nov 2021, 19:04 Reply Quote 0
                        • undefined
                          alankilian @T3P3Tony
                          last edited by 3 Nov 2021, 23:44

                          @t3p3tony

                          Thanks for the offset infor.

                          Neither Sinplify3D nor my online GCODE viewer pay attention to G10, so I was unable to figure it out myself.

                          Printing PLA at 210C I get:

                          Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 28.80mm/rev, allow 60% to 160%, check every 3.0mm, version 3, mag 130 agc 117, measured sensitivity 24.51mm/rev, min 94% max 113% over 171.5mm

                          SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                          1 Reply Last reply Reply Quote 1
                          • undefined
                            T3P3Tony administrators @wouldstain
                            last edited by 4 Nov 2021, 10:01

                            @wouldstain tested this on a Duet 2 with my current config:

                            Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 24.78mm/rev, allow 0% to 150%, check every 3.0mm, version 3, mag 132 agc 60, measured sensitivity 24.58mm/rev, min 96% max 110% over 190.2mm
                            Finished printing file 0:/gcodes/pla_250c_drywall_anchor.gcode, print time was 0h 14m

                            www.duet3d.com

                            undefined 1 Reply Last reply 4 Nov 2021, 11:37 Reply Quote 0
                            • undefined
                              T3P3Tony administrators @T3P3Tony
                              last edited by T3P3Tony 11 Apr 2021, 11:38 4 Nov 2021, 11:37

                              @wouldstain and now with your config (except for removing the bits that don't apply to the test rig):

                              Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 131 agc 60, measured sensitivity 24.52mm/rev, min 95% max 111% over 190.2mm
                              Finished printing file 0:/gcodes/pla_250c_drywall_anchor.gcode, print time was 0h 14m

                              That is with a Hermera. I will switch back to the titan as well for a further test.

                              www.duet3d.com

                              undefined 1 Reply Last reply 4 Nov 2021, 12:01 Reply Quote 0
                              • undefined
                                T3P3Tony administrators @T3P3Tony
                                last edited by 4 Nov 2021, 12:01

                                @wouldstain and now with the Titan:

                                Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 129 agc 59, measured sensitivity 23.78mm/rev, min 95% max 106% over 180.9mm
                                Finished printing file 0:/gcodes/pla_250c_drywall_anchor.gcode, print time was 0h 14m

                                So can't reproduce this with your setup on my extruders. can you do me a favour and print a PETG print (the drywall anchor) and then print the PLA print (same as before) without making changes in between other than temperature an PA as needed and see if you get the differences you have seen earlier between PETG settings and PLA.

                                www.duet3d.com

                                1 Reply Last reply Reply Quote 0
                                • undefined
                                  wouldstain @T3P3Tony
                                  last edited by 4 Nov 2021, 19:04

                                  @T3P3Tony

                                  Ran this using a different spool of PETG only because its what I had loaded this morning (Atomic Starry Night).

                                  1. Temp
                                    PETG: 235 start, 230 other layers
                                    PLA: 235 start, 230 other layers

                                  2. Print Speed:
                                    PETG: 60 perim / 80 infill
                                    PLA: 60 perim / 80 infill

                                  3. Retraction settings:
                                    PETG: 7mm / 25mm/sec
                                    PLA: 2mm / 25mm/sec

                                  4. PA settings (in this instance):
                                    PETG: .06
                                    PLA: .07

                                  5. Z offset for PETG = -.15

                                  Really not a lot of difference.

                                  I have tried adjusting all of the above settings when printing with PLA with no improvement.

                                  undefined 1 Reply Last reply 4 Nov 2021, 20:23 Reply Quote 0
                                  • undefined
                                    wouldstain @wouldstain
                                    last edited by 4 Nov 2021, 20:23

                                    @wouldstain Was actually able to successfully print a drywall anchor in both PETG and PLA using the PETG setting (including Z offset) however, was unable to complete 20mm calibration cube in PLA using same settings.

                                    undefined undefined 2 Replies Last reply 4 Nov 2021, 20:45 Reply Quote 0
                                    • undefined
                                      T3P3Tony administrators @wouldstain
                                      last edited by 4 Nov 2021, 20:45

                                      @wouldstain ahh ok the difference I missed in original PETG file you shared was the 7mm retractions, however the 2mm on PLA is working well in my tests.

                                      Would be good to see the actual results reported by M591 for the PETG and PLA drywall prints that worked and the PLA cube that did not.

                                      www.duet3d.com

                                      undefined 1 Reply Last reply 5 Nov 2021, 22:18 Reply Quote 0
                                      • undefined
                                        wouldstain @wouldstain
                                        last edited by wouldstain 11 Apr 2021, 22:54 4 Nov 2021, 22:41

                                        @wouldstain

                                        had a couple successful PLA prints on the drywall anchor using the PETG settings.
                                        1x1, 1x2. failed on 2x3.

                                        Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 26.50mm/rev, allow 1% to 200%, check every 3.0mm, version 3, mag 130 agc 75, measured sensitivity 26.60mm/rev, min -30% max 111% over 443.4mm

                                        there does not seem to be any rhyme or reason to it.

                                        I am going to switch back to PETG as I have something else I need to print.

                                        BTW I've had the same problem with several different spools of PLA from different manufacturers.

                                        I had been experiencing this with PETG but far less frequently but have not had an occurrence since installing the beta+1 version as instructed.

                                        Just to make things more interesting, I'm seeing this in the console in several locations:

                                        G28
                                        Error: G0/G1: insufficient axes homed
                                        File 0:/gcodes/Drywall_Anchor_PLA_2x3_Test.gcode selected for printing

                                        i tested and verified that the endstops are working.

                                        Please let me know what to try next.

                                        alankilianundefined 1 Reply Last reply 5 Nov 2021, 15:25 Reply Quote 0
                                        • alankilianundefined
                                          alankilian @wouldstain
                                          last edited by 5 Nov 2021, 15:25

                                          I've been printing a few smallish things the last couple of days and it seems that the magnetic filament monitor is really working for me now!

                                          Duet3D rotating magnet filament monitor v3 on pin e0stop, enabled, sensitivity 28.80mm/rev, allow 60% to 160%, check every 3.0mm, version 3, mag 130 agc 119, measured sensitivity 25.90mm/rev, min 96% max 104% over 3793.7mm
                                          

                                          Thanks for working on this again.

                                          I can do test-prints if anyone has suspicious files.

                                          SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                                          1 Reply Last reply Reply Quote 0
                                          111 out of 151
                                          • First post
                                            111/151
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA