• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

M566 P1 vs pressure advance

Scheduled Pinned Locked Moved
Beta Firmware
4
25
937
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    PCR @AlexTh
    last edited by 23 Nov 2021, 10:30

    @alexth you have to tune PA with the specific jerk settings and policy.

    undefined 1 Reply Last reply 23 Nov 2021, 10:34 Reply Quote 0
    • undefined
      AlexTh @PCR
      last edited by 23 Nov 2021, 10:34

      @pcr I can't find the PA value, because the perimeter prints well, and only the beginning of the line with high underextrusion.

      undefined 1 Reply Last reply 23 Nov 2021, 10:39 Reply Quote 0
      • undefined
        PCR @AlexTh
        last edited by 23 Nov 2021, 10:39

        @alexth which printer? A PA value of 0,1 is quite high

        undefined undefined 2 Replies Last reply 23 Nov 2021, 10:39 Reply Quote 0
        • undefined
          PCR @PCR
          last edited by 23 Nov 2021, 10:39

          @pcr for a direct drive

          1 Reply Last reply Reply Quote 0
          • undefined
            AlexTh @PCR
            last edited by AlexTh 23 Nov 2021, 10:43

            @PCR
            Flying Bear 5
            Long direct
            ~10 cm

            20211117_124318.jpg

            undefined 1 Reply Last reply 23 Nov 2021, 10:45 Reply Quote 0
            • undefined
              PCR @AlexTh
              last edited by 23 Nov 2021, 10:45

              @alexth start with S0 and increase?

              undefined 2 Replies Last reply 23 Nov 2021, 10:47 Reply Quote 0
              • undefined
                AlexTh @PCR
                last edited by AlexTh 23 Nov 2021, 10:47

                @pcr I've tried different values. Can't set up.

                But I'll try again

                1 Reply Last reply Reply Quote 0
                • undefined
                  AlexTh @PCR
                  last edited by 23 Nov 2021, 11:18

                  @pcr M572 D0 S0.07 is a more appropriate value, there is no underextrusion at the beginning of the line, but the outer corners of the model are slightly outward. For the perimeter, this value is not ideal.

                  undefined 1 Reply Last reply 23 Nov 2021, 11:27 Reply Quote 0
                  • undefined
                    PCR @AlexTh
                    last edited by 23 Nov 2021, 11:27

                    @alexth please print a tuning tower from S0 to S0.1 and show the pictures

                    undefined 1 Reply Last reply 23 Nov 2021, 12:14 Reply Quote 0
                    • undefined
                      AlexTh @PCR
                      last edited by 23 Nov 2021, 12:14

                      @pcr Give me a link to the test

                      undefined 1 Reply Last reply 23 Nov 2021, 12:22 Reply Quote 0
                      • undefined
                        PCR @AlexTh
                        last edited by 23 Nov 2021, 12:22

                        @alexth https://duet3d.dozuki.com/Wiki/Pressure_advance
                        or
                        https://forum.duet3d.com/topic/25764/pressure-advance-tuning-with-conditional-g-code?_=1635840827943

                        1 Reply Last reply Reply Quote 0
                        24 out of 25
                        • First post
                          24/25
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA