Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    DWC displaying text only

    Scheduled Pinned Locked Moved
    General Discussion
    3
    26
    807
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jay_s_ukundefined
      jay_s_uk @brian
      last edited by

      @brian M122 not M112

      Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

      1 Reply Last reply Reply Quote 0
      • brianundefined
        brian @brian
        last edited by brian

        @brian Final result after completing the connecting instructions, and still cant get DWC on pc.

        M112<CR>
        M112
        M112
        Emergency Stop! Reset the controller to continue.ok
        RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.02(RTOS) dated 2018-12-24b1

        Executing config.g...Error: Bad command: ++
        HTTP is enabled on port 80
        FTP is disabled
        TELNET is disabled

        Done!
        RepRapFirmware for Duet 2 WiFi/Ethernet is up and running.
        WiFi module started
        WiFi module is connected to access point TELUS008
        M115 S-1
        FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.02(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-12-24b1
        ok
        M552 S-0
        ok
        WiFi module is idle
        M552 S-0
        ok
        M552
        WiFi module is idle
        ok
        M587 S"TELUSxx87" P"5n6w6xxxcc"
        ok
        M552 S1
        ok
        WiFi module is connected to access point TELUS0087, IP address 192.168.1.66

        1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          Send M122 please.

          And can you share your config.g?

          Z-Bot CoreXY Build | Thingiverse Profile

          brianundefined 1 Reply Last reply Reply Quote 0
          • brianundefined
            brian @Phaedrux
            last edited by

            @phaedrux yes

            ++;MY update june 16 2018 for pellet extruder
            ; Configuration file for Duet WiFi (firmware version 2.0) Wifi not working, z endstop not working
            ; executed by the firmware on start-up
            ;
            ; generated by RepRapFirmware Configuration Tool on Tue Jun 20 2017 17:30:36 GMT-0700 (Pacific Daylight Time)

            ; General preferences***********************
            M111 S0 ; Debugging off
            G21 ; Work in millimetres
            G90 ; Send absolute coordinates...
            M83 ; ...but relative extruder moves
            M555 P2 ; Set firmware compatibility to look like Marlin
            M208 X0 Y0 Z0 S1 ; Set axis minima
            M208 X420 Y430 Z650 S0 ; Set axis maxima
            M564 H0 ; must be here to allow movements before homing ...wtf

            ; Endstops -my not working model******************
            ;M574 X1 Y1 S1 ; Define active high microswitches took out Z1 maybe cant have both-nope
            ;M558 P1 X0 Y0 Z1 H-3 F320 T5000 R0 ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed ;5000mm/min, no recovery time
            ;M557 X25:175 Y25:175 S25 ; Define mesh grid
            ;G31 P500 X0 Y0 Z not here; Set Z probe trigger value, offset and trigger height HIGHER numbers moves bed CLOSER to nozzle-well it used to, nothing
            ;G30 ;does move bed up to trigger height* try z-2 or something-didnt home didnt go up

            ; Endstops -T3P3Tony****************************
            ;
            ; Set Z height from build plate*********************

            M574 X1 Y1 S1 ; try remove Z0-didnt help, try Y2 flipped wires and work, now x not working trying X2
            M558 P1 H3 F200 T1000 ;smart IR Z probe, (H)dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min travel speed was 5000 testing at 1000
            G31 X0 Y0 Z0.4 P500 ; *****1.20 for 0.4 nozzle 2.0 for 0.9 HIGHER num puts bed CLOSER to nozzle! 1/1/21
            ;setting z height, command bed up to nozzle, run G92 Z0, set z to 0 in above line, repeat then run M114 to get offset

            ; Drives*********************************************
            M569 P0 S1 ; Drive 0 goes forwards
            M569 P1 S1 ; Drive 1 goes forwards
            M569 P2 S1 ; Drive 2 goes forwards
            M569 P3 S1 ; Drive 3 goes forwards; **below set microstepping to 64 from 128 now next line reduce steps by half x1272 y1284 z 6400-which worked!!!!
            M350 X32 Y32 Z16 E32 I0 ; Configure microstepping without interpolation---below line was Z3200 Z3500=10% too much
            by measuring 100mm with yardstick 3150 appears exactly correct!

            ; STEPS **************************************

            M92 X322.5 Y322.5 Z1307.8 E1300 ; ** (247 recreus E w/1.8 stepper, 500 for 0.9 stepper)(x636 642-1.8 steppers) 1360-dyze pro E-steps per mm trying y645 to correct printed(Z 3200 for 1,8 steppers try 5100 for 0.9 z,sy 2020 added 30 to 5100 to try reduce nozzle drag) 642 change for x y 5130 z (e1143 worked good for 1.0 LH), (e4000 good for 0.4LH) and (e1250 try 1750 too much for 0.6 LH) (try 700 for 0,9 Nozzle

            M566 X100 Y100 Z100 E50 ; Set maximum instantaneous speed changes (mm/min); I changed from 900 x y (@12 prints very slowly)june 1 2018 120 z400 original ju27 2021 reduced E60 to E50
            M203 X4800 Y4800 Z200 E1000 ; Set maximum speeds (mm/min)
            M201 X600 Y600 Z100 E100 ; Set accelerations (mm/s^2) ; I changed from 1000 x y to 300 and now 200 and now lets try 300 june1 2018 Oct 600 xy 600

            ;POWER ******************

            M906 X855 Y855 Z1800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent *** tried 2000 works great but gets really hot 1800 hot, 1700 skips
            M84 S30 ; Set idle timeout

            ; Heaters
            M143 S300 ; Set maximum heater temperature to 300C
            M140 H-1 ; Disable heated bed
            ;M305 P1 X201 ; (board v0.4)
            M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
            M305 P2 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
            M307 H1 A350 C500 D50 B1; I added this line for pellet extruder C500 gives more timeout time; re-ativated as too many timeouts

            ; Tools
            M563 P0 D0 H1 ; Define tool 0
            G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
            G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

            ; Network
            M550 PBRIAN'S Build 2 ; Set machine name
            M552 S1 ; Enable network
            ; Access point is configured manually via M587 by the user
            M586 P0 S1 ; Enable HTTP
            M586 P1 S0 ; Disable FTP
            M586 P2 S0 ; Disable Telnet

            ; Fans changed p1 and p2 to S0 from S1 to see if they will work
            M106 P1 S0 I0 F500 H1 T50 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
            M106 P1 S0 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
            M106 P2 S0 I0 F500 H1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

            ; Miscellaneous
            T0 ; Select first tool

            Phaedruxundefined 1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator @brian
              last edited by

              @brian said in DWC displaying text only:

              ++;MY update june 16 2018 for pellet extruder

              You've got a ++ before the ; for the comment which is causing that bad command error.

              Executing config.g...Error: Bad command: ++

              @brian said in DWC displaying text only:

              @brian Ok, i replaced all the www files on the sd card, but this has not made a difference. (that is on the new sd card)

              What version of DWC files did you use? You'd need to match the files to your firmware version.

              @brian said in DWC displaying text only:

              RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.02(RTOS) dated 2018-12-24b1

              It looks like you're on 2.02 which is quite old now.

              Z-Bot CoreXY Build | Thingiverse Profile

              brianundefined 1 Reply Last reply Reply Quote 0
              • brianundefined
                brian @Phaedrux
                last edited by

                @phaedrux said in DWC displaying text only:

                version of DWC files

                Have deleted the ++ in config.g

                Version of DWC files; not sure version, but dated 2018, i think from when i installed the firmware, should be same install

                Is 3.3 the latest and can i update just by copying files to sdcard?

                1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator
                  last edited by

                  For firmware 2.02 I think you'd want to use these DWC files.

                  https://github.com/Duet3D/RepRapFirmware/releases/download/2.02/DuetWebControl-1.22.6.zip

                  Updating to 3.3 would take a bit more doing. Let's see if we can resolve the DWC displaying correctly first.

                  Can you send M122 and post the results? Not M112.

                  Z-Bot CoreXY Build | Thingiverse Profile

                  brianundefined 1 Reply Last reply Reply Quote 0
                  • brianundefined
                    brian @Phaedrux
                    last edited by

                    @phaedrux agree, fix this first.

                    M122 Diagnostic RepRepFirmware for duet 2
                    WiFi/Ethernet version 2.20(RTOS)running on Duet
                    WiFi 1.02 or later Board ID: then the id number

                    brianundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
                    • brianundefined
                      brian @brian
                      last edited by

                      @brian updated www files from your link. no change

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator @brian
                        last edited by

                        @brian said in DWC displaying text only:

                        M122 Diagnostic RepRepFirmware for duet 2
                        WiFi/Ethernet version 2.20(RTOS)running on Duet
                        WiFi 1.02 or later Board ID: then the id number

                        That's all that comes with it? There should be a longer diagnostic report.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        brianundefined 1 Reply Last reply Reply Quote 0
                        • brianundefined
                          brian @Phaedrux
                          last edited by

                          @phaedrux i just got that from Panel Due, i will run Yat and see. BTW heres screenshot of my Home Router showing the ip address when i turn on printer.
                          Home Network showing 66 is printer.jpg

                          brianundefined 1 Reply Last reply Reply Quote 0
                          • brianundefined
                            brian @brian
                            last edited by

                            @brian

                            RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.02(RTOS) dated 2018-12-24b1

                            Executing config.g...Error: Bad command: ++
                            HTTP is enabled on port 80
                            FTP is disabled
                            TELNET is disabled

                            Done!
                            RepRapFirmware for Duet 2 WiFi/Ethernet is up and running.
                            WiFi module started
                            WiFi module is connected to access point TELUS008
                            M122
                            === Diagnostics ===
                            RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
                            Board ID: 08DGM-956GU-DGMSN-6JKF2-3S86Q-TBRRH
                            Used output buffers: 1 of 20 (4 max)
                            === RTOS ===
                            Static ram: 25524
                            Dynamic ram: 98480 of which 0 recycled
                            Exception stack ram used: 288
                            Never used ram: 6780
                            Tasks: NETWORK(ready,1428) HEAT(blocked,1232) MAIN(running,3844) IDLE(ready,200)
                            Owned mutexes:
                            === Platform ===
                            Last reset 00:00:36 ago, cause: power up
                            Last software reset time unknown, reason: Unknown, spinning module Platform, available RAM 6408 bytes (slot 1)
                            Software reset code 0x00b0 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0042380f BFAR 0xe000ed38 SP 0x20001ef4 Task 0x5754454e
                            Stack: 004450eb 00446c74 01000000 00000001 0040607f 200187cc a5a5a501 a5a5a5a5 20018a58 00000000 00000001 00000001 200099bc a5a5a5a5 a5a5a5a5 a5a5a5a5 00407a81 00000000 00000000 20001f48 00000014 3fff0300 00000000
                            Error status: 0
                            Free file entries: 10
                            SD card 0 detected, interface speed: 12.0MBytes/sec
                            SD card longest block write time: 0.0ms, max retries 0
                            MCU temperature: min 33.2, current 35.9, max 35.9
                            Supply voltage: min 0.2, current 0.4, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
                            Driver 0: ok, SG min/max not available
                            Driver 1: ok, SG min/max not available
                            Driver 2: ok, SG min/max not available
                            Driver 3: ok, SG min/max not available
                            Driver 4: ok, SG min/max not available
                            Date/time: 1970-01-01 00:00:00
                            Cache data hit count 114777159
                            Slowest loop: 1.08ms; fastest: 0.06ms
                            I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
                            === Move ===
                            Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
                            Scheduled moves: 0, completed moves: 0
                            Bed compensation in use: none
                            Bed probe heights: 0.000 0.000 0.000 0.000 0.000
                            === Heat ===
                            Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
                            Heater 1 is on, I-accum = 0.0
                            === GCodes ===
                            Segments left: 0
                            Stack records: 1 allocated, 0 in use
                            Movement lock held by null
                            http is idle in state(s) 0
                            telnet is idle in state(s) 0
                            file is idle in state(s) 0
                            serial is ready with "M122" in state(s) 0
                            aux is idle in state(s) 0
                            daemon is idle in state(s) 0
                            queue is idle in state(s) 0
                            autopause is idle in state(s) 0
                            Code queue is empty.
                            === Network ===
                            Slowest loop: 15.74ms; fastest: 0.00ms
                            Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                            HTTP sessions: 0 of 8

                            • WiFi -
                              Network state is running
                              WiFi module is connected to access point
                              Failed messages: pending 0, notready 0, noresp 0
                              WiFi firmware version 1.23
                              WiFi MAC address 84:0d:8e:b2:37:d2
                              WiFi Vcc 3.45, reset reason Turned on by main processor
                              WiFi flash size 4194304, free heap 24256
                              WiFi IP address 192.168.1.66
                              WiFi signal strength -32dBm, reconnections 0, sleep mode modem
                              Socket states: 0 0 0 0 0 0 0 0
                              ok
                            Phaedruxundefined 1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator @brian
                              last edited by

                              @brian said in DWC displaying text only:

                              SD card 0 detected, interface speed: 12.0MBytes/sec

                              Thanks. 12MB/s would indicate there is a problem with the SD card interface. It should be 20MB/s for the Duet 2.

                              When and where did you purchase the Duet? Firmware version 2.02 would indicate it's a bit old?

                              Z-Bot CoreXY Build | Thingiverse Profile

                              brianundefined 1 Reply Last reply Reply Quote 0
                              • brianundefined
                                brian @Phaedrux
                                last edited by brian

                                @phaedrux I purchased it a couple years ago, my second, as the first had many problems. I got it from Spool3D in canada, it is listed as a supplier on the duet3d site.

                                1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator
                                  last edited by

                                  Unfortunately that is well out of warranty, but occasionally we have refurbished boards we can offer at reduced cost on exchange. Please contact roland@duet3d.com to enquire about availability and include a link to this thread.

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  brianundefined 1 Reply Last reply Reply Quote 0
                                  • brianundefined
                                    brian @Phaedrux
                                    last edited by

                                    @phaedrux ok, thanks for all your help

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA