• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

I could use some help

Scheduled Pinned Locked Moved
Duet Hardware and wiring
11
682
63.5k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    fcwilt @A Former User
    last edited by 28 Jun 2022, 21:40

    @mac said in I could use some help:

    @fcwilt I homed again, it went forwards again, and smashed into the adjustment cap again.

    This makes no sense at all.

    OK here is a thought. Perhaps the forwards move is the G1 Y110 at the end of the file.

    So lets try this:

    • jog the bed back to somewhere in the middle of it's travel
    • execute a G91
    • execute a G1 H1 Y-10 which should be a 10mm move. It's not far enough to smack into anything but it will tell us in what direction the G1 H1 Y-10 command moves the bed.

    Thanks.

    Frederick

    ? 1 Reply Last reply 28 Jun 2022, 21:44 Reply Quote 0
    • undefined
      fcwilt @A Former User
      last edited by 28 Jun 2022, 21:41

      @mac said in I could use some help:

      @fcwilt

      What if I change the code to what's below?

      G1 H1 Y 360 F3600
      G1 Y15
      G1 H1 Y=10 F360
      G90
      G1 Y110 F3600

      You are faster than me. I just posted a little test to verify if the G1 H1 move is actually going in the correct direction.

      Frederick

      1 Reply Last reply Reply Quote 0
      • ?
        A Former User @fcwilt
        last edited by 28 Jun 2022, 21:44

        @fcwilt G1 H1 Y-10 moved the bed 10mm towards the END STOP!

        ? 1 Reply Last reply 28 Jun 2022, 21:44 Reply Quote 0
        • ?
          A Former User @A Former User
          last edited by 28 Jun 2022, 21:44

          @fcwilt Interestingly, Y is saying 0.0

          ? 1 Reply Last reply 28 Jun 2022, 21:45 Reply Quote 0
          • ?
            A Former User @A Former User
            last edited by 28 Jun 2022, 21:45

            @fcwilt I did it again, now Y's saying -10

            ? 1 Reply Last reply 28 Jun 2022, 21:46 Reply Quote 0
            • ?
              A Former User @A Former User
              last edited by 28 Jun 2022, 21:46

              @fcwilt I changed the end to Y-20. The bed went towards the rear 20mm. Y is reporting -30mm.

              ? 1 Reply Last reply 28 Jun 2022, 21:49 Reply Quote 0
              • ?
                A Former User @A Former User
                last edited by 28 Jun 2022, 21:49

                @fcwilt according to my measurements, and my inches to millimeter calculator, if I change the number to Y-92.075mm, the foot of the bed will touch the end-stop.

                ? undefined 2 Replies Last reply 28 Jun 2022, 21:52 Reply Quote 0
                • ?
                  A Former User @A Former User
                  last edited by 28 Jun 2022, 21:52

                  @fcwilt hmmmm, the bed's being weird. I'm sending G1 H1 Y-92 , but the bed is inching towards the end stop instead of going straight for it.

                  And Y is now 0.0 again, whereas it was -30.

                  ? undefined 2 Replies Last reply 28 Jun 2022, 21:55 Reply Quote 0
                  • undefined
                    fcwilt @A Former User
                    last edited by 28 Jun 2022, 21:54

                    This post is deleted!
                    1 Reply Last reply Reply Quote 0
                    • ?
                      A Former User @A Former User
                      last edited by 28 Jun 2022, 21:55

                      @fcwilt okay, I've gone back to telling the board to move the bed back 10mm at a time (Y-10). It's working again. Y is at -10.0. It's also (I jogged it twice more), about 5mm from the end stop now.

                      ? 1 Reply Last reply 28 Jun 2022, 21:57 Reply Quote 0
                      • ?
                        A Former User @A Former User
                        last edited by 28 Jun 2022, 21:57

                        @fcwilt I've moved the bed back to the center of the 452mm's. That's 9 inches (of 18). Y is reporting 100.00 now.

                        ? 1 Reply Last reply 28 Jun 2022, 21:57 Reply Quote 0
                        • ?
                          A Former User @A Former User
                          last edited by 28 Jun 2022, 21:57

                          @fcwilt I have to run an errand. I'll be back in an hour.

                          undefined 1 Reply Last reply 28 Jun 2022, 22:01 Reply Quote 0
                          • undefined
                            fcwilt @A Former User
                            last edited by 28 Jun 2022, 22:00

                            @mac said in I could use some help:

                            @fcwilt hmmmm, the bed's being weird. I'm sending G1 H1 Y-92 , but the bed is inching towards the end stop instead of going straight for it.

                            And Y is now 0.0 again, whereas it was -30.

                            The change to Y=0 should be because the endstop was triggered.

                            The post move behavior of a G1 H1 move is to set the axis position to the min or max value specified in the M208 for that axis.

                            Since the endstop for this axis is specified to be at the low end, the min value is used, and that is just what you are seeing.

                            Was the move, while slow, smooth and even?

                            It could because you did not specify an F parameter for the move. In that case it uses the speed set by the last F parameter that was executed.

                            You could try it all again but this time include, say, F3600 in the G1 H1 moves.

                            Frederick

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              fcwilt @A Former User
                              last edited by 28 Jun 2022, 22:01

                              @mac said in I could use some help:

                              @fcwilt I have to run an errand. I'll be back in an hour.

                              Sounds good. I have a chore to do as well.

                              Be safe.

                              Frederick

                              undefined 1 Reply Last reply 28 Jun 2022, 22:57 Reply Quote 0
                              • undefined
                                Nightowl @fcwilt
                                last edited by 28 Jun 2022, 22:57

                                @fcwilt
                                I've got to hand it to you, Frederick. You have tha patience of Job.

                                Few things are more dangerous than taking the advice of someone who thinks he knows what he's doing.
                                I'm still on my learning curve, so take everything I say with caution!

                                RatRig 1075, Duet3 MB6HC, Sorotec SFM 1000 PV-ER milling motor, Hobbyist

                                undefined 1 Reply Last reply 28 Jun 2022, 23:03 Reply Quote 0
                                • undefined
                                  fcwilt @Nightowl
                                  last edited by 28 Jun 2022, 23:03

                                  @nightowl said in I could use some help:

                                  @fcwilt
                                  I've got to hand it to you, Frederick. You have tha patience of Job.

                                  Uh... I like a challenge?

                                  Frederick

                                  ? undefined 2 Replies Last reply 28 Jun 2022, 23:08 Reply Quote 1
                                  • ?
                                    A Former User @fcwilt
                                    last edited by 28 Jun 2022, 23:08

                                    @fcwilt

                                    G91
                                    G1 H1 Y-220 F3600

                                    Send
                                    FC869CF0-602B-45C5-AE1C-328E3AC3E21F.jpeg

                                    undefined ? 2 Replies Last reply 28 Jun 2022, 23:09 Reply Quote 0
                                    • undefined
                                      fcwilt @A Former User
                                      last edited by 28 Jun 2022, 23:09

                                      @mac

                                      Hey mac,

                                      What am I seeing?

                                      Did something work as expected for once? 😉

                                      Frederick

                                      ? 1 Reply Last reply 28 Jun 2022, 23:27 Reply Quote 0
                                      • ?
                                        A Former User @A Former User
                                        last edited by 28 Jun 2022, 23:23

                                        @fcwilt @droftarts @alankilian @Nightowl

                                        link text

                                        undefined 1 Reply Last reply 28 Jun 2022, 23:27 Reply Quote 0
                                        • undefined
                                          fcwilt @A Former User
                                          last edited by 28 Jun 2022, 23:27

                                          @mac said in I could use some help:

                                          @fcwilt @droftarts @alankilian @Nightowl

                                          link text

                                          Hey mac,

                                          Nice but G1 H2 is not the same as G1 H1.

                                          To make use of the endstop for homing, you have to use G1 H1.

                                          Frederick

                                          ? 2 Replies Last reply 28 Jun 2022, 23:31 Reply Quote 0
                                          455 out of 682
                                          • First post
                                            455/682
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA