duet 3 6hc and raspberry p3b+
-
@sgk m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-9P63L-DJ3S0-7J1F8-3S46T-TVKH9
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162760 of which 48 recycled
Exception stack ram used: 224
Never used ram: 75580
Tasks: ETHERNET(blocked,844) NETWORK(ready,1972) HEAT(blocked,1200) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,204) MAIN(running,4952) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:04:04 ago, cause: power up
Last software reset time unknown, reason: User, spinning module LinuxInterface, available RAM 74824 bytes (slot 1)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 24.5, current 36.0, max 36.1
Supply voltage: min 24.0, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: standstill, reads 15483, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 15484, writes 14 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 15484, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 15485, writes 14 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 15485, writes 14 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 15489, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2022-08-26 18:45:34
Slowest loop: 4.51ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.65ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8- Ethernet -
State: establishingLink
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 647, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 1
Last transfer: 15ms ago
RX/TX seq numbers: 19844/19844
SPI underruns 4, overruns 1
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.4.1
Failed to deserialize the following properties: - Spindle -> Int32 from 10000.0000000
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 1
Full transfers per second: 40.80, max time between full transfers: 182.3ms, max pin wait times: 30.7ms/23.8ms
Codes per second: 0.01
Maximum length of RX/TX data transfers: 3176/308
- Ethernet -
-
@sgk M98 P "config.g"
Error: M98: non-empty string expected -
@sgk I hooked everything up like the picture here
-
@sgk said in duet 3 6hc and raspberry p3b+:
@sgk M98 P "config.g"
Error: M98: non-empty string expectedYou've got a space between P and "
-
@sgk said in duet 3 6hc and raspberry p3b+:
Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Update your Pi and firmware with sudo apt update and sudo apt upgrade from the pi terminal.
-
@phaedrux yes ok
-
@phaedrux hello the same nothing works neither the fans nor the motors
-
Did you re-run
M98 P"config.g"?
Is this a coreXY?Have you seen this?
-
@phaedrux i have blv yes I read but before I had a duet 2 now I installed a duet 3 and I have a lot of worries for that I ask for help I'm sorry I'm lost with it
-
@phaedrux
yes i launched M98 P"config.g" -
@phaedrux
I have the impression that there is something wrong because when I start the fans nothing lights up and the motor lights up but it advances step by step very slowly 1 cm by a cm -
@sgk look home
video.mp4 -
@sgk i have this.
-
What version of firmware does it have now?
Did you update on the Pi?
What version of DWC does it show it has? -
@phaedrux Board: Duet 3 MB6HC (MB6HC)
DSF Version: 3.4.1
Firmware: RepRapFirmware for Duet 3 MB6HC 3.1.1 (2020-05-19b2) -
I did the update with pi but now the motors don't work very well and the fans still don't work says it all
-
@phaedrux that's when I do home x and the same for home yvideo 2.mp4
-
@sgk said in duet 3 6hc and raspberry p3b+:
DSF Version: 3.4.1
Firmware: RepRapFirmware for Duet 3 MB6HC 3.1.1 (2020-05-19b2)You have a mismatch. When the pi updated the duet firmware didn't get updated at the same time. Please send M997 to initiate a manual firmware update and then check again with M115.
-
@phaedrux 27/08/2022 00:28:39 m115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.4.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2022-06-01 21:09:12
27/08/2022 00:28:22 Connection established
27/08/2022 00:28:22 CORS disabled
27/08/2022 00:28:22 CORS disabled
27/08/2022 00:28:22 CORS disabled
27/08/2022 00:28:22 Error: M552: Network-related commands are not supported when using an attached Single Board Computer
27/08/2022 00:28:16 m997
27/08/2022 00:21:32 Connection established -
Ok, so now when you send M122 you should see matching firmware and DCS versions of 3.4.1.
Now in DWC can you check the DWC version?
