Some strange things with Superslicer and Duet.

TomasL

@phaedrux No supports, just two whels for the bed adustment, 20mm in dia and 4 mm high.
It was finished after som 26 layers or so.

Phaedrux

Can you share the gcode file?

TomasL

@phaedrux Yes
JusterRatt_0.15mm_PLA_MK2.5_1h25m.gcode
And the STL
JusterRatt.stl

Why cant I upload it as a ZIP-file?

oliof

@tomasl look here, line 40342, filament specific end gcode

G1 Z33.95 ; Move print head up

So that's where that comes from. And peeking at the HEIGHT comments, 33.95/0.15 = 226

So that's that.

TomasL

@oliof
I found this row in the "Printer Setting Custom G-codes"

M107 ; turn off fan
{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; Move print head up
G1 X0 Y200 F3000 ; home X axis

Should it be commented out?

droftarts

@tomasl said in Some strange things with Superslicer and Duet.:

{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; Move print head up

Just add an "E" at the beginning of the comment, then the line will be ignored, eg:

{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ;E Move print head up

Ian

Phaedrux

@tomasl said in Some strange things with Superslicer and Duet.:

Why cant I upload it as a ZIP-file?

The forum software doesn't allow it. Possibly because you never know what's actually inside a zip file.

RogerPodacter

i noticed on my new RatRig printer, any STL i slice with SuperSlicer, the Duet Web Interface always says 1 of 900 layers printing. the 900 never changes, no matter which Gcode i load to the Duet 3 Mini 5+. Its weird but i just assumed it was a bug in the slicer.

Phaedrux

@rogerpodacter said in Some strange things with Superslicer and Duet.:

i noticed on my new RatRig printer, any STL i slice with SuperSlicer, the Duet Web Interface always says 1 of 900 layers printing. the 900 never changes, no matter which Gcode i load to the Duet 3 Mini 5+. Its weird but i just assumed it was a bug in the slicer.

Can you share an example gcode file?

RogerPodacter

@phaedrux I should have clarified, this is on the mobile web version when i connect with my iPhone 11 Pro. Attached gcode and screenshot. Duet Web.jpg y_max_endstop_slider_3.1 Extended Direct Mount_0.2mm_PLA_6m.gcode

Phaedrux

@rogerpodacter I think it's the same issue as above. Z moves in the end gcode that don't have ;E in the comment so they are getting picked up as normal print Z moves.

G1 Z10 F600 ; Move print head up
G1 X5 Y240 F15000 ; present print
G1 Z78 F600 ; Move print head further up
G1 Z180 F600 ; Move print head further up

Add ;E to the comments on those Z moves in the slicer end gcode and those Z moves will be ignored by DWC.

RogerPodacter

@phaedrux thanks, i revised my custom end gcode which is where those lines were coming from and seems to fix the issue.

{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ;END Move print head up{endif}
G1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ;END present print
{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ;END Move print head further up{endif}
{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ;END Move print head further up{endif}
M140 S0 ; turn off heatbed
M104 S0 ; turn off temperature
;M107 ; turn off fan
M84 X Y E ; disable motors