Mesh leveling for multiple extruders
-
I can see setting different Z values based on each extruder but not for bed leveling? A crooked bed is a crooked bed. once you know how to flatten it then all of the extruders should use the same map. Unless the y gantries aren't parallel with each other, in that case I would indicate them in to all be parallel.
-
So, don't bother? – use one mesh from any arbitrary tool (tool 1 is easiest) and then just set the Z offset for the rest. I supposes I was trying to get a bit more out of the fact that each tool has a piezo in it
-
I stopped using mesh bed leveling long ago, just make sure your bed is flat, the piezo probe will ensure you always have the correct Z-height, the rest should not be needed
-
I stopped using mesh bed leveling long ago, just make sure your bed is flat, the piezo probe will ensure you always have the correct Z-height, the rest should not be needed
so what do you do instead for auto bed leveling? G32? I'm using it for lead screw compensation. I'm figuring g29 to create a mesh. It's a large bed 610mm – flat as it gets -- very small sag in the center -- the probe measures 0.1mm diff between center and edges.
-
yes only G32, I have a i3 like setup and the 2 screw calibration works flawless in combination with the piezo sensor.
Whenever I startup the printer I will do a G32 because the motors will be out of sync anyway.
My first layer is always correct now since I use this feature.
If you have a flat bed then G29 is really useless… -
yes only G32, I have a i3 like setup and the 2 screw calibration works flawless in combination with the piezo sensor.
Whenever I startup the printer I will do a G32 because the motors will be out of sync anyway.
My first layer is always correct now since I use this feature.
If you have a flat bed then G29 is really useless…how many points to do you use for G32 (in bed.g I suppose)
-
only 2 as I have 2 leadscrews…
-
only 2 as I have 2 leadscrews…
yea, that's only enough to sync up the lead screws, and that requires manually leveling the bed – sorta defeats the purpose of having a probe IMO.
I just want to get it close by eye and then let software compensate for the rest -
The probe is needed for accurate leadscrew compensation.
I do use G29 to check that the bed is leveled, once the bed is leveled you never need to do it again. -
so I guess, manually send the head to different spots and adjust – thought of that, but I basically have it pretty level as is -- but the machine is too big and bed is too big to get it perfect, and I'm after perfect -- I ran G29 on it 2 weeks ago -- and I had the entire bed STD was ~0.2mm -- so I have it close already. I'll try it again tonight now that things are more stable and secure. I now have glass secured to the aluminum, so all mechanicals are done. Time to level and calibrate the extruders for XYZ offsets
-
…................. I now have glass secured to the aluminum, so all mechanicals are done. ..................
Is the glass toughened? I found out the hard way that the toughening process causes the glass to distort so plain float glass is better.
-
…................. I now have glass secured to the aluminum, so all mechanicals are done. ..................
Is the glass toughened? I found out the hard way that the toughening process causes the glass to distort so plain float glass is better.
I use borosilicate glass with PEI attached on top – never use plain glass on a heated bed, especially this big -- last thing I need is this thing to crack from heat. And it's flat -- absolutely flat, got it direct from the manufacturer who basically invented the process of creating borosilicate sheets -- they made it custom to my spec (if you're in US, they're the place to go for borosilicate glass, not some reseller who gets it from who knows where)
-
Lovely discovery yesterday – my Y gantries were not parallel -- out by 5 mm -- took some minor disassembly, and some end stop adjustments but now parallel to as low as my caliper measures.
