Upgrading after 1.5yrs

jay_s_uk

@tsitalon1 can you reupload the 3.3 zip file then try again?

tsitalon1

@jay_s_uk said in Upgrading after 1.5yrs:

3.3 zip file then try

Won't re-apply 3.3 now, same error, even though I'm already on 3.3:

Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.3 (2021-06-15)
Duet WiFi Server Version: 1.25

I'm using the Duet2CombinedFirmware.bin file

dc42

@tsitalon1 upload file Duet2_SDiap32_WiFiEth.bin from the release to your Duet; then you should be able to upgrade to 3.4.x.

jay_s_uk

@tsitalon1 I meant use the combinedduet2and3.zip or whatever it's called

tsitalon1

Worked now on:

Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.5 (2022-11-30)
Duet WiFi Server Version: 1.27

Thank you both !

Now to see if things still work...

tsitalon1

Looks like i lost my extruder after the upgrades:

; Heaters
M308 S0 P"bed_temp" Y"thermistor" R4700 T100000 B3950 				; define bed temperature sensor
M143 H0 S120                                                        ; Set temperature limit for heater 0 to 120C
M308 S1 P"e0_temp" Y"thermistor" T100000 B4815 C7.06e-8 R4700 		; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M140 H0 ; the bed heater is heater 0
M143 H1 S280                   				             			; Set temperature limit for heater 1 to 280C
M307 H1 R2.546 C123.4 D3.51 S1.00

; Fans

M950 F0 C"fan0" Q125                           						; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 						; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           						; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              						; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                           						; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H0 T30                              						; set fan 2 value. Thermostatic control is turned on



; Tools
M563 P0 D0 H1 S"HotEnd"                                             ; Define tool 0
G10 P0 X0 Y0 Z0                                                     ; Set tool 0 axis offsets
G10 P0 R0 S0                                                        ; Set initial tool 0 active and standby temperatures to 0C

T3P3Tony

@tsitalon1 send M98 P"config.g" to run your config.g file after the machine has booted it will show you which command(s) have errors in them.

tsitalon1

@T3P3Tony No errors noted:

tsitalon1

M122 only listing one heater, but I see nothing wrong with my heater section in Config.g:

=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===

; Heaters
M308 S0 P"bed_temp" Y"thermistor" R4700 T100000 B3950 				; define bed temperature sensor
M143 H0 S120                                                        ; Set temperature limit for heater 0 to 120C
M308 S1 P"e0_temp" Y"thermistor" T100000 B4815 C7.06e-8 R4700 		; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M140 H0 ; the bed heater is heater 0
M143 H1 S280                   				             			; Set temperature limit for heater 1 to 280C
M307 H1 R2.546 C123.4 D3.51 S1.00

tsitalon1

Figured it out, 3.3 release notes listed this:

All extruders must be declared explicitly using M584. In previous firmware versions, one default extruder was assign to driver 3.

Once I input M584 E3 in my config.g, it now listed both heaters and my extruder... off to a test print