• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Scanning Z probe support in RRF 3.5

Scheduled Pinned Locked Moved
Beta Firmware
23
128
10.1k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    flyscha @jay_s_uk
    last edited by flyscha 1 May 2024, 14:25 5 Jan 2024, 14:24

    @jay_s_uk Ok thanks! Are you using an SBC?

    undefined 2 Replies Last reply 5 Jan 2024, 14:26 Reply Quote 0
    • undefined
      jay_s_uk @flyscha
      last edited by 5 Jan 2024, 14:26

      @flyscha no, standalone

      Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

      1 Reply Last reply Reply Quote 0
      • undefined
        jay_s_uk @flyscha
        last edited by 5 Jan 2024, 14:27

        @flyscha if you're using DWC to upload it should ask you to update. if you're pulling the SD card and loading the file you'll need to send M997 B69

        Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

        undefined 1 Reply Last reply 5 Jan 2024, 14:33 Reply Quote 1
        • undefined
          flyscha @jay_s_uk
          last edited by 5 Jan 2024, 14:33

          @jay_s_uk Thank you! I for sure ran the M997 B69 after replacing the .bin file on the SD card last night, but maybe something got mixed up when moving bin files around.

          I'll try it all again tonight. Much appreciated!

          undefined 1 Reply Last reply 6 Jan 2024, 05:41 Reply Quote 1
          • undefined
            flyscha @flyscha
            last edited by 6 Jan 2024, 05:41

            @jay_s_uk I tried over and over and over and somehow FINALLY the firmware updated! I must have tried 5 or 6 times, and it just so happened to stick. I won't speak too loudly or else it may scare it back to the previous version.

            @dc42 The new firmware was absolutely the fix for me! Now when I run the M122 diagnostics, I get 0 I2C bus errors. Every now and then there are a few naks (always 0 or 3), but that's about it.

            When sending the G29 command, I now get scanning probe coefficients, and the entire bed scans without any stops, errors, or hiccups.

            Thanks for everyone's help!

            undefined 1 Reply Last reply 6 Jan 2024, 11:56 Reply Quote 0
            • undefined
              dc42 administrators @flyscha
              last edited by 6 Jan 2024, 11:56

              @flyscha I'm glad it's working for you.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • undefined
                becky9
                last edited by 10 Jan 2024, 12:48

                Where can I get the scanning probe in the UK at the moment? Looked on E3D & Ooznest can't see it x

                undefined 1 Reply Last reply 12 Jan 2024, 16:26 Reply Quote 0
                • undefined
                  tkamsker
                  last edited by 11 Jan 2024, 09:26

                  @dc42 said in Scanning Z probe support in RRF 3.5:

                  https://www.youtube.com/watch?v=969s3J8EEyM

                  Hi i might being late to that thread but i have an (several) duet 2 boards and i would love to upgrade my E3D tool changer to that Z-Probe so question how is that possible ? i see all infos refer to Duet 3 board ,. i would love to not totally rework my printers thx thomas

                  undefined undefined 2 Replies Last reply 11 Jan 2024, 09:42 Reply Quote 0
                  • undefined
                    jay_s_uk @tkamsker
                    last edited by 11 Jan 2024, 09:42

                    @tkamsker it doesn't support duet 2 boards as it requires CAN-FD (which the duet 2 doesn't support)

                    Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      dc42 administrators @tkamsker
                      last edited by dc42 1 Nov 2024, 15:29 11 Jan 2024, 15:29

                      @tkamsker also we have run out of flash memory space in Duet 2. After 3.5 I expect to move Duet 2 and Maestro firmware to "bug fixes only" maintenance status because it doesn't have enough flash or RAM space for significant new features.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 3
                      • undefined
                        T3P3Tony administrators @becky9
                        last edited by 12 Jan 2024, 16:26

                        @becky9 we are working on it, in the meantime if you drop an email to sales@duet3d.com we should be able to help.

                        www.duet3d.com

                        1 Reply Last reply Reply Quote 0
                        127 out of 128
                        • First post
                          127/128
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA