• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Duet3D announces new tool board at FormNext

Scheduled Pinned Locked Moved
General Discussion
25
107
8.8k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    Edkirk
    last edited by 9 Jan 2024, 13:11

    New Duet3D tool board up and running on Voron Trident, with Tap on Z axis for homing and bed leveling. Micro Swiss NG extruder, E3d heater and nozzle.20240109_053911.jpg

    1 Reply Last reply Reply Quote 2
    • undefined
      Edkirk
      last edited by 11 Jan 2024, 00:28

      Are there plans for a Delta Smart Effector with built-in Tool Board, I would install on my Delta?

      undefined 1 Reply Last reply 11 Jan 2024, 00:32 Reply Quote 0
      • undefined
        demonio669 @Edkirk
        last edited by 11 Jan 2024, 00:32

        @Edkirk +1 I also want this board!!

        undefined 1 Reply Last reply 11 Jan 2024, 17:56 Reply Quote 0
        • undefined
          dc42 administrators @demonio669
          last edited by 11 Jan 2024, 17:56

          @demonio669 @Edkirk please see https://forum.duet3d.com/topic/34657/combined-smart-effector-and-tool-board-for-delta-printers.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • undefined
            jltx
            last edited by 21 Jan 2024, 16:24

            Does the tool board come with uncrimped pins or do I need to source those myself? e3d told me the leads on the Roto extruder are 1m long so I would need to remove 90% of the wire and reposition the connectors to use this tool board mounted locally.

            undefined 1 Reply Last reply 22 Jan 2024, 17:39 Reply Quote 0
            • undefined
              T3P3Tony administrators @jltx
              last edited by 22 Jan 2024, 17:39

              @jltx the leads on the Roto and Revo that are directly connected are very short and those plug directly into the Roto Toolboard. E3d provides extension cables to take them out to 1m.

              Crimps and connectors are provided to handle the JST connectors which are not part of the Roto Extruder, or Revo hotend, for example a part cooling fan.

              www.duet3d.com

              1 Reply Last reply Reply Quote 0
              • undefined
                soran28h
                last edited by 23 Jan 2024, 11:55

                Lets see, nearest competitor is the BD sensor, runs around $30 plus many weeks delay to get shipped here. And a toolboard, either the Ebb36 or fly run around $45+. Then I would get to integrate it into the controller board/Raspberry Pi ecosystem ( Pi boards are dropping in price but still expensive ) that is needed along with the work needed to control all the parts. Make sure you RTFM before you ask any questions if you get stuck. And praise Klipper to high heaven on any post.

                1 Reply Last reply Reply Quote 0
                • undefined
                  Edkirk
                  last edited by Edkirk 24 Jan 2024, 13:55

                  I have the board up and running, I am getting low on the little white connector pins. They are very fragile and I almost out. Where can I get some more of the metal connectors? Are they the same as used on the Smart Effector? Thanks, Ed

                  undefined 1 Reply Last reply 24 Jan 2024, 19:16 Reply Quote 0
                  • undefined
                    dc42 administrators @Edkirk
                    last edited by dc42 24 Jan 2024, 19:16

                    @Edkirk they are JST PH2.0 connectors. You can buy the shells and pins from the usual electronic component distribution companies, and on Amazon, eBay etc.

                    The version 4 Smart Effector uses the same crimp pins.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    undefined 1 Reply Last reply 24 Jan 2024, 21:00 Reply Quote 0
                    • undefined
                      Edkirk @dc42
                      last edited by 24 Jan 2024, 21:00

                      @dc42 Great, Thank you. I am using the new tool board on a full size extruder/hot end. Awesome combination. I am thinking about getting another one for my delta/smart effector, sure cleans up the wiring and much more convenient and easier to work with. Thanks, Ed

                      undefined 1 Reply Last reply 25 Jan 2024, 09:28 Reply Quote 0
                      • undefined
                        droftarts administrators @Edkirk
                        last edited by 25 Jan 2024, 09:28

                        @Edkirk A description of the pins and their connector type is here: https://docs.duet3d.com/Duet3D_hardware/Duet_3_family/Duet_3_Roto_Toolboard#description-of-connections

                        I have also added them here: https://docs.duet3d.com/en/User_manual/Troubleshooting/Parts#connectors-used-on-duet-3-roto-toolboard

                        Ian

                        Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA