Issue with Heater 1 Predicted Maximum Temperature Warning

droftarts

@R006 said in Issue with Heater 1 Predicted Maximum Temperature Warning:

So this will not affect the printing or the machine?

No, it's just a warning to say if you set it to a high temperature, while turning off limits such as M143 and M570, or the heater suffers from thermal runaway (possibly if there's a wiring fault), things are going to get very hot!

Ian

R006

@droftarts
okay,
Is there any way to re-solved this (like electronic end)?

droftarts

@R006 Can you post the exact error message? I misread your first post, where you said:

Heater 1 has reached a predicted ...

The usual error message is something like:

Warning: Heater 1 predicted maximum temperature at full power is 589°C

Obviously these are two quite different things. You should only get the message at startup. As far as I'm aware there's no way to disable it. It's just a warning. The only way to avoid it is to fit a lower power heater, and retune the heater.

Ian

R006

@droftarts
Warning: Heater 1 predicted maximum temperature at full power is 589°C
okay

Phaedrux

The warning is telling you what temperature it calculates as the maximum that could be reached in a failure condition where power was stuck on. It's up to you do mitigate that with a thermal fuse that could physically cut power to the heater when a temperature has been reached. They usually only cost a few cents and are used in everyday appliances that have heaters like kettles or toasters.

R006

@Phaedrux @droftarts :

thank you for the clarification. I will try for fuse, before that I have couple of questions more:

If this warning appears, then it must appear every time for that machine or heater , right ?
Is it possible to reduce "S" value in M307, so that it never uses 100% PWM & may not cause this effect?

note: My concerns is to remove this warning, so that client does not mis interpret this as a problem with the extruder heating.

droftarts

@R006 said in Issue with Heater 1 Predicted Maximum Temperature Warning:

If this warning appears, then it must appear every time for that machine or heater , right ?

As far as I know, there's no way to remove the warning message. However, it only shows at startup, and as it is a warning, it will disappear after 5 seconds. And you will only see it on the PanelDue or in DWC if you are already connected.

Is it possible to reduce "S" value in M307, so that it never uses 100% PWM & may not cause this effect?

That may remove the warning (though I'm not sure it will), but then your heater will take a lot longer to heat up, as it is using less power. It also doesn't protect you from a MOSFET or wiring failure, where the hot end would receive 100% power, and hit the temperature predicted.

The only real way around this is to fit a less powerful heater. But then, again, it will take longer to heat up.

Ian

R006

@droftarts
Okay,
I have two machine with same heater. but this warning message appears only in one machine. heater watt is 50.
So can i do something with its resistor value.

deckingman

@R006 If you get a warning that a heater could potentially reach a dangerous temperature, then the safest way to address this is to use a less powerful heater. Then if say a MOSFET failed, the heater would get hot, but not dangerously so.

droftarts

@R006 Are both machines running the same firmware version? Check in config.g what the M307 command is for each heater; they are probably different. If you have M501 in config.g, also check config-override.g for M307.

The code for the warning is here: https://github.com/Duet3D/RepRapFirmware/blob/1f1ce4c1adbce5bc32e141a1940c697b71e02c22/src/Heating/Heater.cpp#L237

The firmware makes a prediction, based on M307 parameters, what the highest temperature is. If this is higher than the maximum heater temperature (set by M143) - ambient temperature, then multiplied by 1.5 plus 50, you get the warning.

Ian

R006

@droftarts
Thank you.
After changing the 50W heater to a 40W heater, the warning no longer appears on one machine, but it should still be showing on the other machine. Now, I want to add a comment about this in RRF 3.4b3, but I am encountering multiple errors.

Building file: ../src/GPIO/GpOutPort.cpp
Building file: ../src/GCodes/GCodeBuffer/BinaryParser.cpp
Invoking: Cross G++ Compiler
Invoking: Cross G++ Compiler
arm-none-eabi-g++ -std=gnu++17 -D__SAME70Q20B__ -DRTOS -DDUET3_V06 -D_XOPEN_SOURCE -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\common\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\cmsis\same70\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\arm\CMSIS\5.4.0\CMSIS\Core\Include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\preprocessor" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\header_files" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\drivers" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Hardware\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\portable\GCC\ARM_CM7\r0p1" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RRFLibraries\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CANlib\src" -O2 -Wall -c -mcpu=cortex-m7 -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -mno-unaligned-access -ffunction-sections -fdata-sections -fno-threadsafe-statics -fno-rtti -fexceptions -nostdlib -Wundef -Wdouble-promotion -Werror=return-type -Wsuggest-override -fsingle-precision-constant "-Wa,-ahl=GpOutPort.s" -fstack-usage -MMD -MP -MF"src/GPIO/GpOutPort.d" -MT"src/GPIO/GpOutPort.o" -o "src/GPIO/GpOutPort.o" "../src/GPIO/GpOutPort.cpp"
arm-none-eabi-g++ -std=gnu++17 -D__SAME70Q20B__ -DRTOS -DDUET3_V06 -D_XOPEN_SOURCE -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\common\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\cmsis\same70\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\arm\CMSIS\5.4.0\CMSIS\Core\Include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\preprocessor" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\header_files" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\drivers" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Hardware\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\portable\GCC\ARM_CM7\r0p1" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RRFLibraries\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CANlib\src" -O2 -Wall -c -mcpu=cortex-m7 -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -mno-unaligned-access -ffunction-sections -fdata-sections -fno-threadsafe-statics -fno-rtti -fexceptions -nostdlib -Wundef -Wdouble-promotion -Werror=return-type -Wsuggest-override -fsingle-precision-constant "-Wa,-ahl=BinaryParser.s" -fstack-usage -MMD -MP -MF"src/GCodes/GCodeBuffer/BinaryParser.d" -MT"src/GCodes/GCodeBuffer/BinaryParser.o" -o "src/GCodes/GCodeBuffer/BinaryParser.o" "../src/GCodes/GCodeBuffer/BinaryParser.cpp"
../src/Hardware/ExceptionHandlers.cpp: In function 'void SoftwareReset(SoftwareResetReason, const uint32_t*)':
../src/Hardware/ExceptionHandlers.cpp:86:9: error: 'ResetProcessor' was not declared in this scope
Finished building: ../src/Hardware/I2C.cpp
86 | ResetProcessor();
| ^~~~~~~~~~~~~~
../src/Hardware/ExceptionHandlers.cpp: In function 'void OutOfMemoryHandler()':
../src/Hardware/ExceptionHandlers.cpp:92:57: error: 'GetStackPointer' was not declared in this scope
92 | SoftwareReset(SoftwareResetReason::outOfMemory, GetStackPointer());
| ^~~~~~~~~~~~~~~
../src/Hardware/ExceptionHandlers.cpp: In function 'void Terminate()':
../src/Hardware/ExceptionHandlers.cpp:286:61: error: 'GetStackPointer' was not declared in this scope
286 | SoftwareReset(SoftwareResetReason::terminateCalled, GetStackPointer());
| ^~~~~~~~~~~~~~~

../src/Hardware/ExceptionHandlers.cpp: In function 'void __cxa_pure_virtual()':
../src/Hardware/ExceptionHandlers.cpp:296:66: error: 'GetStackPointer' was not declared in this scope
296 | SoftwareReset(SoftwareResetReason::pureOrDeletedVirtual, GetStackPointer());
| ^~~~~~~~~~~~~~~
../src/Hardware/ExceptionHandlers.cpp: In function 'void __cxa_deleted_virtual()':
../src/Hardware/ExceptionHandlers.cpp:301:66: error: 'GetStackPointer' was not declared in this scope
301 | SoftwareReset(SoftwareResetReason::pureOrDeletedVirtual, GetStackPointer());
| ^~~~~~~~~~~~~~~
Building file: ../src/GCodes/GCodeBuffer/ExpressionParser.cpp
../src/Hardware/ExceptionHandlers.cpp: In function 'void OutOfMemoryHandler()':
../src/Hardware/ExceptionHandlers.cpp:93:1: warning: 'noreturn' function does return
93 | }
| ^
../src/Hardware/ExceptionHandlers.cpp: In function 'void Terminate()':
../src/Hardware/ExceptionHandlers.cpp:287:1: warning: 'noreturn' function does return
287 | }
| ^
../src/Hardware/ExceptionHandlers.cpp: In function 'void __cxa_pure_virtual()':
../src/Hardware/ExceptionHandlers.cpp:297:1: warning: 'noreturn' function does return
297 | }
| ^
../src/Hardware/ExceptionHandlers.cpp: In function 'void cxa_deleted_virtual()':
../src/Hardware/ExceptionHandlers.cpp:302:1: warning: 'noreturn' function does return
302 | }
| ^
Invoking: Cross G++ Compiler
make[1]: *** [src/Hardware/subdir.mk:33: src/Hardware/ExceptionHandlers.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Finished building: ../src/Hardware/NonVolatileMemory.cpp
arm-none-eabi-g++ -std=gnu++17 -D__SAME70Q20B -DRTOS -DDUET3_V06 -D_XOPEN_SOURCE -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\common\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\cmsis\same70\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\arm\CMSIS\5.4.0\CMSIS\Core\Include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\preprocessor" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\utils\header_files" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CoreN2G\src\SAM4S_4E_E70\asf\sam\drivers" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Hardware\SAME70" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RepRapFirmware\src\Networking\LwipEthernet\Lwip\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\include" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\FreeRTOS\src\portable\GCC\ARM_CM7\r0p1" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\RRFLibraries\src" -I"C:\Users\rishita.butala\eclipse-workspace\Firmware_updatedM109\CANlib\src" -O2 -Wall -c -mcpu=cortex-m7 -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -mno-unaligned-access -ffunction-sections -fdata-sections -fno-threadsafe-statics -fno-rtti -fexceptions -nostdlib -Wundef -Wdouble-promotion -Werror=return-type -Wsuggest-override -fsingle-precision-constant "-Wa,-ahl=ExpressionParser.s" -fstack-usage -MMD -MP -MF"src/GCodes/GCodeBuffer/ExpressionParser.d" -MT"src/GCodes/GCodeBuffer/ExpressionParser.o" -o "src/GCodes/GCodeBuffer/ExpressionParser.o" "../src/GCodes/GCodeBuffer/ExpressionParser.cpp"

Finished building: ../src/Hardware/IoPorts.cpp

Finished building: ../src/Hardware/SoftwareReset.cpp

Finished building: ../src/GPIO/GpInPort.cpp

Finished building: ../src/GPIO/GpOutPort.cpp

Finished building: ../src/GCodes/GCodeBuffer/BinaryParser.cpp

Finished building: ../src/GCodes/GCodeBuffer/ExpressionParser.cpp

make: *** [makefile:98: all] Error 2
"make -j8 all" terminated with exit code 2. Build might be incomplete.

10:55:51 Build Failed. 8 errors, 8 warnings. (took 46s.991ms)

Phaedrux

@R006 said in Issue with Heater 1 Predicted Maximum Temperature Warning:

Now, I want to add a comment about this in RRF 3.4b3, but I am encountering multiple errors.

Best to start a new thread about your build errors.